MEDMASTER CLEANSCENE™
MRI/Imaging Suite Luminaires
CSMRI SERIES
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
1
PREP INSTALLATION SURFACE
• Disconnect power to all circuits before
wiring system.
• Install in accordance with all national,
state, and local codes.
• Do not connect to an ungrounded supply.
Flange Mounting
• Wiring connections must be made internal
to the enclosure.
• Failure to install unit on a mechanically-
sound surface may result in personal injury,
physical damage, or potential re hazard.
• Use installation procedures appropriate for
an environment involving MRI and sensitive
electronic equipment.
• Read all markings and labels to ensure
correct installation of the power supply.
Supplemental instructions may be located
on the enclosure, in addition to this
instruction sheet, regarding orientation, or
mounting restrictions.
• Read instructions provided with the
MedMaster™ MRIPS-312 external power
supply for proper installation and electrical
connection to the lighting system.
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
GENERAL
• Read instructions provided with the
MedMaster™ MRIPS-312 external power
supply for proper installation and electrical
connection to the lighting system.
INSTALLATION INSTRUCTIONS
• The CleanScene MRI™ lighting system
contains sensitive electronics. Take care
to avoid damage by improper handling or
static electricity discharge (ESD). Either
type of damage could render the
system inoperable.
Lightbox Mounting Procedure
CleanScene MRI™ lightboxes are designed
for either 1” or 1½” (G10 or G15
respectively—see product label) T-bar grid
systems with vertical grid T thickness of less
than ¼”. Grid systems can be installed with
standard 24” x 24”, 24” x 48” or 48” x 48”
centerline grid spacing.
Use the following procedure to install the
lightbox(es) into the ceiling grid:
• Unpack products from the shipping carton.
• Determine where lightbox(es) will be
mounted and note the desired orientation
of graphic images within room.
INSTALLATION INSTRUCTIONS
GENERAL
• Lift lightbox(es) into ceiling structure using
a recommended minimum of two able-
bodied individuals.
• Lay lightbox(es) into grid.
• Attach support wires between hanger
brackets and ceiling support structure.
• Mount and wire the MRIPS-312 external
power supply per the procedures provided
in the supplementar conduit and DC wiring
to an MRI room EMI lter sized to the
load of the power supply (supplied by
others).completely enclosed in grounded
aluminum conduit. Any gaps, regardless
of size, must be closed and/or wrapped in
copper foil tape.
2
NOTE: For installations with a multiple-
conguration (the image is divided among
multiple lightboxes), make sure lightbox is
oriented toproduce a continuous image.
• It is recommended that the door remain
attached to the lightbox housing during
installation. This will prevent damage to
internal components, particularly the LED
light sources. All electrical connections are
accessible through the external junction
box located on the top of the
lightbox housing.
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
• If a 0-10V dimmer is to be connected,
install at this time. Dimmer must be
installed outside the shielded MRI
environment with an intermediate MRI
room EMI lter to the luminaire(s). Kenall
recommends using a Leviton
®
IllumaTech
IP710 series dimmer or Grak Eye GRX-TVI
control interface. Contact Kenall for
suitability of using an alternate sink-type
0-10V dimmer.
™
CSMRI_F-3732_050813
INSTALLATION INSTRUCTIONS
3
INSTALLATION INSTRUCTIONS
• After the luminaires are mounted and
secured, labeled and color coded for easy
identication.
• Run the 24VDC supply from the EMI lter
to luminaires(s) using at least 18 AWG
wires. Class 1 wiring is required. Make sure
wiring is completely enclosed in grounded
aluminum conduit. Any gaps, regardless
of size, must be closed and/or wrapped in
copper foil tape. Special attention should
be paid to the wiring entry point into the
shielded space. See Fig. 2.
• Make DC supply and (optional) dimmer
control connections within each luminaire.
Cap gray and violet leads if dimmer is
not connected.
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
INSTALLATION INSTRUCTIONS
4
INSTALLATION INSTRUCTIONS
• Using at least an 18 AWG wire, ground
the last housing in the sequence to the
shielded ceiling. This can be done by
fastening the wire to one of the luminaire’s
junction box screws.
• Reinstall all provided bracketry and internal
enclosures provided with the luminaire.
These parts are critical to the overall EMI
shielding of the system.
• Connect power to external power supply
and test for proper operation of lighting
system. Make sure all LEDs are lit and
dimming operation works as intended (if
connected).
• Test operation of lighting during MRI
machine idle mode and during
scanning operations.
• Fill out the Installation Registration Form
(attached to MRIPS-312 instruction sheet)
and fax to Kenall at (847) 360-1781.
II. Door Opening, Closing and
Removal Procedure
NOTE: OPENING THE DOOR DURING
NORMAL INSTALLATION IS NOT NECESSARY.
ALL WIRING SHOULD BE ACCESSED
THROUGH THE EXTERNAL JUNCTION BOX
MOUNTING AT THE TOP OF THE
LIGHTBOX HOUSING.
Opening the Door
• Unfasten all door screws. The screws
contain a captive washer which prevents it
from falling out of the door. Only unfasten
to thepoint where the screw is disengaged
from the xture housing. Door will now
hang freely about 1½” below the housing.
• Test operation of lighting during MRI
machine idle mode and during
scanning operations.
• Disengage spring clips from xture housing
on one side of the door. This will allow the
door to pivot down (see WARNING)
WARNING: DO NOT ALLOW THE DOOR TO
SWING DOWN FREELY. SERIOUS PERSONAL
OR PROPERTY DAMAGE MAY
OCCUR. PIVOT DOOR SLOWLY UNTIL IT
RESTS VERTICALLY.
• Perform internal maintenance with door
hanging vertically. To change graphic image
the door will need to be removed.
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
Removing the Door
• Open door following instructions in the
previous section.
• CSMRI24 and CSMRI44: With door hanging
vertically, grasp sides of door frame and
lift vertically to disengage the door catch
hooks from the housing. The door is now
detached from the lightbox. See Figure 3.
INSTALLATION INSTRUCTIONS
Installing the Door (CSMRI22)
• Lift door by spring clips on one side.
• Engage spring clips on one side to
hang vertically.
Closing the Door
• With catch hooks (clips for CSMRI22)
properly engaged into housing, swing door
from the bottom end, up until the spring
clips on the opposite side meet the
housing ange. Figure 4 - Door Assembly
• Squeeze spring clips and insert into slots
on housing ange (located near the lens
gasket). Door will now hang horizontally
below the lightbox approximately 1½”.
5
• CSMRI22 only: This product contains
four (4) spring clips to retain the door
after removing the screws. To remove
door,disengage the remaining spring clips.
• Lay door at on a protected surface while
performing maintenance.
• If the intent of removing the door is to
change the graphic image, please refer
to Section IV.
Installing the Door (CSMRI24 and CSMRI44)
• Lift door with the catch arms upward.
• Hook catch arms into housing ange so
that catch arms rest on housing ange and
engage the mating slots on the housing.
• The door should now hang freely. Check for
proper engagement of catch hooks before
closing door.
• Push up on one side of the door so that
the captive lens screws meet the cage nuts
attached to the housing.
• Fasten lens screws into place by working
around the perimeter. No specic fastening
order is required.
Check to ensure that all screws are
adequately tightened to maintain ratings
on xture. All screws should be equally
torqued—do not over-torque.
IV. Changing the Graphic Image Panel
The graphic panel may need to be changed
periodically due to desired change
of appearance and/or UV degradation. Use
the following procedure to replace
the graphic panel.
• Unfasten and remove door following the
procedure in Section III.
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
NOTE: HANDLING THE GRAPHIC PANEL
SHOULD BE DONE IN A CLEAN, DUST-FREE
ENVIRONMENT TO PREVENT
TRAPPED PARTICLES BETWEEN THE CLEAR
OUTER LENS AND THE GRAPHIC PANEL.
HANDLE WITH EXTREME CARE BY
USING PROTECTIVE MEASURES. SOLVENTS
AND OILS FROM THE SKIN MAY
PERMANENTLY DAMAGE THE IMAGE.
• Remove hex nuts from all four (4) retaining
brackets on the back side of the door. See
Figure 4.
• Remove retaining brackets and existing
graphic panel.
• Check for dust and contaminants on
the clear lens surface. Clean if necessary
following procedure in Section V.
• Install new graphic panel.
• Reinstall retaining brackets. Make sure
internal hinge/spring clips are installed on
opposite sides of each other and, when
installed into the lightbox, will put the
image in the correct orientation.
INSTALLATION INSTRUCTIONS
• Fasten all hex nuts to retainer brackets.
Torque all fasteners equally to 12 lb-in.
• Reinstall door and fasten lens screws
V. Cleaning the Lens and Graphic Panel
Use the following procedure to properly clean
the graphic panel and clear, acrylic outer lens.
This should be done in a clean, dust-free
environment to avoid additional
contamination. The back side of the graphic
panel is a sensitive photographic lm. Handle
withextreme care. Avoid contact with
solvents and oils from the skin as they may
permanently damage the image.
• Remove graphic panel from door.
• Gently wipe down image with a clean,
damp micro-ber cloth. Hard wiping and
abrasive cloths will scratch the lm and
clear lens.
• For heavier smudges and residue, use a
diluted mild dish soap solution. Afterward,
rinse-off solution with a clean, damp
microber cloth.
• Dry panels with a clean, dry
micro-ber cloth.
6
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
INSTALLATION INSTRUCTIONS
CUSTOMER SERVICE
For technical assistance, call 1-800-4KENALL (1-800-453-6255).
WARRANTY
Kenall reserves the right to issue credit, repair, or replace the defective merchandise, at its discretion, upon
notication and conrmation by its local representative of the defect. Kenall also reserves the right to test and
examine the defective product if the defect is questionable and to deny the warranty herein for any product
altered, improperly installed, installed in applications for which it is not intended. This includes operation in
ambient temperatures above stated limits for any length of time. Failure by electrical surge shall not be covered
under warranty.
Kenall assumes no responsibility for labor or freight costs incurred in connection with the installation, removal, or
replacement of products determined to be defective or any other consequential or incidental damages arising from
the use of the product. Kenall’s entire liability on any claim of loss or damage resulting from a defective product is
limited to the replacement price of the product.
7
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
INSTALLATION INSTRUCTIONS
CUSTOMER ACKNOWLEDGEMENT
Customer acknowledges that these Installation Instructions are part of the product specification, and that the
attached Installation Registration Form will be provided to the installer to sign and return to Kenall after
installation is complete. This signed release is required by Kenall before order will be released into production.
Signature: _________________________________ Date: _________________________________
Print Name: _______________________________ Company Name:__________________________
• Disconnect power to all circuits before wiring system.
• Install in accordance with all national, state, and local codes.
• Do not connect to an ungrounded supply.
• Wiring connections must be made internal to the enclosure.
• Failure to install unit on a mechanically-sound surface may result in personal injury, physical damage, or potential
fire hazard.
• Use installation procedures appropriate for an environment involving MRI and sensitive electronic equipment.
• Read all markings and labels to ensure correct installation of the power supply. Supplemental instructions may be
located on the enclosure, in addition to this instruction sheet, regarding orientation, or mounting restrictions.
• Read instructions provided with the MedMaster
™
MRIPS-312 external power supply for proper installation and
electrical connection to the lighting system.
IMPORTANT SAFEGUARDS
To prevent MRI machine interference, all DC power and dimming signal wiring must be completely shielded within
grounded aluminum conduit and a suitable MRI room EMI filter must be installed on each line.
When using electrical equipment, basic safety precautions should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
SAVE THESE INSTRUCTIONS
8
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
INSTALLATION INSTRUCTIONS
DC supply power and dimming signal are NOT running through the same EMI lter. Check here
9
MRI INSTALLATION REGISTRATION FORM
For warranty purposes, please fill out this form and return to Kenall by fax at (847) 360-1781.
I certify that the lighting installation for the listed MRI suite location is completed per the provided
installation instructions and to the best of my abilities.
Please check off items to denote status:
Installation instruction sheets for MRIPS-312 power supply and individual luminaire(s) read
and followed.
MRIPS-312 power supply and EMI lters are located outside the shielded enclosure.
All DC supply wiring is completely enclosed within grounded aluminum conduit. Installation
has no ungrounded/unshielded portions of conduit or openings of any size or shape.
All dimming signal wiring is completely enclosed within grounded aluminum conduit.
Installation has no ungrounded/unshielded portions of conduit or openings of any size or
shape. Check here if dimming is not applicable:
MRI Room EMI lters for the 24VDC supply are of the type intended for MRI suites and are
sized to the electrical load.
if dimming is not applicable:
Lighting system fully tested (including dimming operation, if applicable) while MRI machine is
in idle and scan operation mode.
If any of these steps cannot be completed or you need technical assistance, please contact Kenall
Technical Support at 1-800-4KENALL (1-800-453-6255).
Electrical Contractor
Name: ___________________________________
City/State: ________________________________
Installation Site
Name: ___________________________________
City/State: ________________________________
Phone:___________________________________
FAX FORM TO (847) 360-1781
Installation Date: ___________________________
(Do not write below line)
Kenall Received By: ___________________________________ Received Date: ________________________________
www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031
CSMRI_F-3732_050813
Loading...