KEMET C052C109D1G5CA User Manual
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630020
CERAMIC MOLDED AXIAL & RADIAL
PERFORMANCE CHARACTERISTICS
GENERAL
Working Voltage:
C0G – 50, 100 & 200 Volts
X7R – 50, 100 & 200 Volts
Temperature Characteristics:
C0G – 0 ±30 PPM/°C from -55°C to +125°C
X7R – ±15% from -55°C to +125°C
Capacitance Tolerance:
C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%
(±0.5 pF is tightest available tolerance)
X7R – ±10%, ±20%, -0 +100%, -20% +80%
Construction:
Monolithic block of ceramic dielectric with interdigitated
internal electrodes, encapsulated in a molded case, and
having axial or radial leads. Meets flame test requirements
of UL Standard 94V-0.
Terminal Strength:
EIA-198 Method 303 Condition A (2.2 kg)
ELECTRICAL
Capacitance:
Within specified tolerance when measured with 1 volt rms
at 1 kHz (1000 pF or less at 1 MHz for C0G).
Dissipation Factor:
25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).
C0G – .15% maximum
X7R – 2.5% maximum
Insulation Resistance:
After 2 minutes electrification at 25°C and rated voltage
C0G – 100K megohms or 1000 megohm - µF, whichever
is less.
X7R – 100K megohms or 1000 megohm - µF, whichever
is less.
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current limited
to 50 mA at 25°C.
Life Test:
2000 hours at 200% of rated voltage at 125°C. Post-Test
limits at 25°C are:
Capacitance Change:
C0G – less than 3% or 0.25 pF, whichever is higher
X7R – ±20% of initial value
Dissipation Factor:
C0G – .25% maximum
X7R – 3.0% maximum
查询C052C109D1G5CA供应商
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
ENVIRONMENTAL
Moisture Resistance:
MIL-STD-202, Method 106, or EIA-198, Method 204,
Condition A, except 20 cycles.
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
Immersion Cycling:
MIL-STD-202, Method 104, Condition B. Post-Test limits
at 25°C are:
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Solderability:
MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2
seconds.
Resistance to Soldering Heat:
MIL-STD-202, Method 210, Condition B (260°C, 10 secs).
Depth of immersion — to a minimum of .050" from the
capacitor body.
Lead Material:
Axial: Solder-coated copper clad steel
Radial: Solder-coated copper standard; 100% tin plated optional
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 21
CERAMIC MOLDED/AXIAL & RADIAL - STANDARD
Lead Dia.
.025
(+.004
-.002)
S
H
1.25
Min.
W
Center Line of leads
within .030" of Center
Line of case.
H
1.25
Min.
L
S
W
.045
Max.
L
C052 C062,
C512,
& C522
Lead Dia.
.025
(+.004
-.002)
DIMENSIONS—INCHES & (MILLIMETERS)
CASE MILITARY
SIZE EQUIVALENT STYLES
LD C
C114 .160 ± .010 (4.06 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)
C124 .250 ± .010 (6.35 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)
C192 .390 ± .010 (9.91 ± .25) .140 ± .010 (3.56 ± .25) .025, +.004, -.001 (.64, +.10, -.025)
C202 .500 ± .020 (12.70 ± .51) .250 ± .015 (6.35 ± .38) .025, +.004, -.001 (.64, +.10, -.025)
C222 .690 ± .030 (17.53 ± .76) .350 ± .020 (8.89 ± .51) .025, +.004, -.001 (.64, +.10, -.025)
CAPACITOR OUTLINE DRAWINGS — (AXIAL LEADS)
CC75, CCR75
CK12, CKR11
CC76, CCR76
CK13, CKR12
CC77, CCR77
CK14, CKR14
CC78, CCR78
CK15, CKR15
CC79, CCR79
CK16, CKR16
CAPACITOR OUTLINE DRAWINGS — (RADIAL LEADS)
DIMENSIONS—INCHES & (MILLIMETERS)
MILITARY S
CASE EQUIVALENT H L W LEAD
SIZE STYLES HEIGHT LENGTH WIDTH SPACING
C052 .190 ± .010 (4.83 ± .25) .190 ± .010 (4.83 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)
C062 .290 ± .010 (7.37 ± .25) .290 ± .010 (7.37 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)
C512 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .140 ± .010 (3.56 ± .25) .400 ± .020 (10.16 ± .51)
C522 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .240 ± .010 (6.10 ± .25) .400 ± .020 (10.16 ± .51)
CC05, CCR05
CK05, CKR05
CC06, CCR06
CK06, CKR06
CC07, CCR07
CC08, CCR08
For packaging information, see pages 39, 40 and 41.
Ceramic Molded
Axial/Radial - Standard
1.50 Min.
(38.10)
1.50 Min.
(38.10)
DL
C
CERAMIC MOLDED/AXIAL & RADIAL - STANDARD
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630022
RADIAL CAPACITOR MARKING
C052C & C062C STANDARD MARKING
100V
K
0511
Voltage
KEMET
Date Code
BACK
C062
X7R
104K
FRONT
Style
Temperature Characteristic
Capacitance, Capacitance Tolerance
C512 & C522 STANDARD MARKING
KEMET
C512X7R
105K 50V
0532
KEMET
SIZE and Temperature Characteristic
Capacitance, Capacitance Tolerance, Voltage
Date Code
ORDERING INFORMATION
**
C
052
C
102
K
R
2
C
5
A
CERAMIC
*CASE SIZE
(See Table Below)
SPECIFICATION
Standard
C — Standard
CAPACITANCE
In picofarad code: First two digits are significant
figures and third is number of zeroes following
(except 9 indicates division by 10). Examples:
0.1 F = 100,000 pF = 104 and 9.1 pF = 919.
See tables for Standard Values.
CAPACITANCE TOLERANCE
Standard
M— ±20%
K — ±10%
J — ±5%
Standard tolerances for each Series are
shown in the repetitive parts lists.
*CASE SIZES
RADIAL AXIAL
C052 C114
C062 C124
C512 C192
C522 C202
C222
Others
H — ±3%
G — ±2%
F — ±1%
D — ±.5 pF
WORKING
VOLTAGE
1 — 100
2 — 200
5 — 50
**Part Number Example: C052C102K2R5CA (14 digits – no spaces)
F AILURE RATE
A — Not Applicable (Std.)
LEAD MA TERIAL
C — Standard
T — 100% Tin plated
(C052, C062 only)
INTERNAL CONSTRUCTION
5 — Standard
TEMPERATURE CHARACTERISTIC
Cap. Change With Temp.
KEMET EIA Temp. DC Bias
Designator Equivalent Range, °C Volta ge
G C0G -55 to ±30
(Ultra (NPO) +125 ppm/°C
Stable)
R X7R -55 to ±15%
(Stable) +125
Measured
Without
STANDARD C114C, C124C, C192C, C202C & C222C
AXIAL CAPACITOR MARKING
KC0G
101J
200V
0512
KEMET, Temperature Characteristic
Capacitance, Capacitance Tolerance
Voltage
Date Code
Loading...