Kelvinator FCCS181QWA, FCCS161QWA, FCCS071QWA, KCNF180QWA, KCNF160QWA Owner’s Manual

COMMERCIAL CHEST FREEZER

TABLE OF CONTENTS

Product Registration .............................................................. 2

Important Safety Instructions ................................................ 2

First Steps .................................................................................. 3

Appliance Start=up ................................................................. 5

Features ................................................................................ 6

Care and Cleaning ..................................................... 6

Energy=Saving Tips ........................................................ 8

Power Failure ..................................................................... 8

Before You Call .............................................................. 9

Wiring Diagram ..................................................................... 11

Warranty ........................................................................... 12

READ AND SAVE THESE INSTRUCTIONS A01063901(August2014)

Product Registration

Read and Save These Instructions

These instructions include information
which is intended to assure the operator of
correct installation, operation and service.
Before attempting installation, adjustment or

maintenance, be certain of the following:

• That you have read and fully understand
the instructions.

That you have all the tools required and are
trained to use them.

That you have met all installation and
usage restrictions and are familiar with the

functions and operations of the unit.
That you follow all instructions exactly

as given.

All the fittings, measurements, recommendations
and procedures are significant. Substitutions

and approximations must be avoided. Improper
handling, maintenance, installation and

adjustment, or service attempted by anyone
other than a qualified technician, may void the
future warranty claims and cause damage to the

unit and/or result in injury to the operator and/
or bystanders.

Record your Model and
Serial Numbers

Record the model number and serial number of
this appliance in the space provided below (the

serial plate is located inside the
cabinet compartment).

Model Number:
Serial Number:
Purchase Date:

Register Your Product
Theself-addressedPRODUCTREGISTRATION

CARD(shownabove)should be filledincompletely,

signedandreturnedto theaddressprovided.

Important Safety Instructions

Read all instructions before using
this appliance,

For Your Safety

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of
this unit or any other appliance. Read product

Child Safety

• Destroy carton, plastic bags, and any
exterior wrapping material immediately
after the appliance is unpacked. Children

should never use these items for play.
Cartons covered with rugs, bedspreads,

plastic sheets or stretch wrap may
become airtight chambers and can

quickly cause suffocation.

• Remove all staples from the carton.
Staples can cause severe cuts, and destroy

finishes if they come in contact with other
appliances or furniture.

• An empty, discarded ice box, refrigerator,
or freezer is a very dangerous attraction
to children.

• Remove and discard any spacers used to
secure the shelves during shipping. Small

.............................objects are a choke hazard to ch!!dren ..........................

Proper Disposal of Appliance

Risk of Child Entrapment

Child entrapment and suffocation are not

problems of the past. 3unked or abandoned
refrigerators or freezers are still dangerous

- even if they will sit for "just a few days" If
you are getting rid of your old refrigerator or

freezer, please follow the instructions below to

p prevent accidents:

Remove the lid.
Have the refrigerant

removed by a

qualified technician.

Important Safety Instructions

Electrical Information Other Precautions

These guidelines must be followed to ensure • NEVER unplug the appliance by
that safety mechanisms in the design of this pulling on the power cord. Always grip

app!iance will operate proper! y............................................... the plug firmly and pull straight out from

not

Avoid fire hazard or electric shock. Do
an extension cord or an adapter plug. Do not

remove any prong from the power cord.... ...............

_rounaln_ type Turning the control to "OFF" turns off the
wall receptacle compressor but does not disconnect power to

Do not, under "_
any circumstances,]

grounQlng prong. /

use

Power supply

cord w!.th3-prong
grounamg p_ug

the receptacle.

• To avoid electrical shock, unplug the
appliance before cleaning.

First Steps

Refer to the serial plate for correct electrical
rating. The power cord of the appliance

is equipped with a three-prong grounding
plug for protection against shock hazards.

It must be plugged directly into its own
properly grounded three-prong receptacle,
protected with a 15-amp time delay fuse

or circuit breaker. The receptacle must
be installed in accordance with the local

codes and ordinances. Consult a qualified
electrician. Receptacles with Ground
Fault Circuit Interrupters (GFCI) are

NOT RECOMMENDED. DO NOT USE AN
EXTENSION CORD OR AN ADAPTER PLUG.

* If the voltage varies by 10 percent or more,

appliance performance may be affected.
Operating the appliance with insufficient

power can damage the compressor. Such
damage is not covered under the warranty.

If you suspect your voltage is high or low,
consult your power company for testing.

* To prevent the appliance from being turned

off accidentally, do not plug the unit into an
outlet controlled by a wall switch or pull cord.

* DO NOT pinch, knot, or bend the power cord

in any manner.

Inspection for Damage

Inspect the underside of the cabinet and
packaging for damage, similar to what can

be caused with a forklift. If hidden damage
is found after uncrating, immediately call the
delivery carrier and request an inspection. Retain

all packaging and crating materials until the
inspection is complete.

Parts and Accessories

* Using a utility knife with a sharp, short

blade, cut along the perimeter of the carton
as indicated.

* Lift the carton off the product.
* Remove the package containing the casters

from the unit.

3

First Steps

The following tools are required to assemble and install the casters to the unit:

A Wrench (1) _ _

B Screws (16) _ _ _

C Casters (4)

Caster Set-up

1. With an assistant, tilt the unit until it is resting on its back. Take care to protect the back from
being scratched during this process.

2. Using the wrench provided and the sixteen (16) screws, install all four (4) casters in the tapped
holes in the bottom of the unit. Tighten the screws securely.

3. With an assistant, tilt the unit back up onto its casters.

4. To prevent unintended movement, block casters once the unit is in place.

Appliance Placement

Leave a three (3) inch space on all sides and the back of the cabinet for ease of installation, proper air
circulation and electrical connections. Choose a place that is near a grounded electrical outlet. For the
most efficient operation, the appliance should be located where surrounding temperatures will not drop

below 40OF (5oc) or exceed 110OF(43oc). Additional compressor heaters are not recommended.

Insulation

The insulated space of this cabinet is sealed to maintain peak efficiency. DO NOT drill holes in the
cabinet. Holes drilled in the cabinet may destroy that seal and damage electrical wiring located in the

insulated space. It may also pierce and damage the sealed refrigeration system in the insulated space.

DAHAGED ELECTRICAL WIRING OR WET INSULATION CAUSED BY DRILLING WILL VOID
THE WARRANTY,

Glass Lid Hodels

• There are two (2) glass lids, a smaller one that fits in the lower track of the ice cream freezer
and a larger one that fits in the upper track. The lower track has two (2) round retaining studs
and the upper has four (4) round retaining studs.

Install the lower glass first. Again, the lower glass is the smaller of the two. It has a flexible vinyl
seal and a lock plate. The flexible seal should be facing up and positioned on the end away from

the two round retaining studs. Place the panel in the center and slide along the lower track until it
is secure under the two retaining studs.

Place the upper glass panel over the lower glass panel already in place. Slide it over the lower
lid past the flexible seal. You will notice a slight resistance with the lower lid gasket. Slide the
upper panel under the four studs on the upper track of the frame.

When properly installed, there is a seal formed by the flexible vinyl seal between the two glass lids.

4