ASSEMBLY INSTRUCTION
TWO TONE COFFEE & ANTIQUE GREY FINISH 18” BUTTERFLY LEAF DINING TABLE
A
Table Top
1 pc
B
E F
Flat Washer
5/16”x22mm
8 pcs
Table Legs
4 pcs
Wrench
12.8mm
1 pc
C D
Hex Bolt
5/16”
8 pcs
Lock Washer
5/16”(M8)
8 pcs
1
This page lists all the contents included
in the box. Please take the time to identify
the hardware as well as the individual
components to this product. As you
unpack and prepare for assembly, place
the contents on a carpeted or padded
area to protect them from damage.
1
Turn the table top (A) upside down on a protective surface such as carpet or other soft material.
Place the Leg (B) to corner of Apron, then tighten the Flat Washer (E), Lock washer (D) and Hex Bolt (C)
using the Wrench (F) provided. Repeat the same for the other Legs. Set the Table (A) upright on its
Legs (B).
B
B
A
E
D
C
F
2
Unlock the hook underneath the table and pull the Table Top (A) wide open equally from both end.
Lift both leaves from the compartment.
A
A
B
3
Flip down the aprons and unfold leaf and place the leaf on the Table Top (A) surface carefully.
Push Table Top (A) from both ends to close. Lock the hook underneath the table.
A
B
CLEANING & CARE
Treat surface with care.Surface is resistant to scratches but is not scractch resistant.Clean surface with a
dry or damp soft cloth.Do not use abrasive cleaners. Hardware may loosen over time. Periodically check
that all connections are tight.
2
ASSEMBLY INSTRUCTION
TWO TONE COFFEE & ANTIQUE GREY FINISH SIDE CHAIR
A
Seat Box
1 pc
E
Drywall Screw
8x1"
6 pcs
I
Flat Washer
B
Chair Back
F
JCBC Screw
M6 x 40mm
2 pcs 8 pcs
J
Allen key
1 pc
C
Front Legs
2 pcs
G
JCBC Screw
M6 x 70mm
D
Hardseat
1 pc
H
Lock Washer
M6 x 13mm
10 pcs
M6.5 x 16.5mm
10 pcs
M4 x 2.1/2"
1 pc
This page lists all the contents included in the box. Please
take the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area to
protect them from damage.
1
1
Position the Chair Back (B) on a soft surface such as a carpet. Place the chair apron frame on to th
middle rail of the Chair Back (B) with the dowel fully inserted into the pre-drilled hole. Make sure that
the screw holes on the apron frame are facing down.
(Fig.1.1)
J
G
H
I
(Fig.1.2)
1.1. Insert JCBC Screw (G) through a Lock Washer (H)
and a Flat Washer (I) into the pre-drilled holes on
Seat Box (A) at rear corners.
J
F
H
I
1.2. Insert the JCBC Screw (F) through a Lock Washer (H)
and a Flat Washer (I) into the pre-drilled holes on the
Seat Box (A) at Chair Back (B).
A
Take the Allen Key, and turn the botls until the legs are
B
secure.DOTNOT TIGHTEN COMPLETELY.Stop when
you feel you are adding force to tighten the bolt.
e
the
2
Insert the JCBC Screw (G) through a Lock Washer (H), a Flat Washer (I) and the pre-drilled holes of
corner block into the pre-drilled holes on the Front Leg (C), tighten the JCBC Bolt (G) with Allen Key (J)
provided. Flip chair upside down and secure the Hardseat (D) with the Drywall Screw (E) through the
pre-drilled holes on the apron frame.
C
Stand chair up on an even surface and check
that it is balanced. If there is a slight wobble,
apply downward pressure in the corner where a
D
leg is uneven,keeping pressure in that corner
tighten all bolts.If balanced, apply downward
pressure evenly in the cantre and tighten all bolts.
Don not over-tighten beyond hole depth.
Helpfull Tip :
B
C
A
G
J
I
H
E
D
-Instead of applying downward pressure
while reaching under to tighten bolts, have
someone sit in the chair while you tighten
A
the bolts.
CLEANING & CARE
Treat surface with care.Surface is resistant to scratches but is not scractch resistant.Clean surface with a
dry or damp soft cloth.Do not use abrasive cleaners. Hardware may loosen over time. Periodically check
that all connections are tight.
2
Loading...