Assembly Instructions
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
EASY
DIFFICULT
Page 1 of 7
Tools Required for Assembly:
Allen Wrench
(Included)
Wrench
(Included)
Phillips Screwdriver
(Not Included)
2 PERSONS RECOMMENDED
Page 2 of 7
MD
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Parts List
#1 x 1 pc
Headboard
#2L x 1 pc
Left H/Board Leg
#4 x 1 pc
Footboard
#6 x 2 pcs
Side Rail
#8 x 8 pcs
#2R x 1 pc
Right H/Board Leg
#3 x 1 pc
Leg Support
#5 x 2 pcs
Footboard Foot
#7 x 4 pcs
Slat
Slat Support Leg
Note: Right and left are determined
by facing the front of the bed in the
upright position.
Page 3 of 7
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALW AYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage.
Hardware List
#A x 4 pcs
Bolt 1/4”x1-1/2”
#C x 8 pcs
Lock W asher
#E x 1 pc
Allen Wrench
#G x 8 pcs
Hex Nut
#I x 1 pc
#B x 4 pcs
Bolt 1/4”x2-1/8”
#D x 8 pcs
Flat W asher
#F x 8 pcs
Threaded Stud
#H x 8 pcs
Beveled W asher
#J x 8 pcs
Wrench
Screw 1-1/4”
Page 4 of 7
I. Align the leg support (#3) with the pre-drilled holes of the right
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
III. Insert the bolt assemblies through the leg support (#3) using the
#A x 4 pcs
#C x 4 pcs
#D x 4 pcs
headboard leg (#2R) and the left headboard leg (#2L).
(#C) onto the bolt (#A) and then the flat washer (#D) onto the
SAME bolt (#A), in that order.
Allen wrench (#E) to lock them with the right headboard leg (#2R)
and the left headboard leg (#2L).
Turn right (clockwise) to tighten
#B x 4 pcs
#C x 4 pcs
#D x 4 pcs
I. With the help of another person, carefully align the headboard
(#1) with the pre-drilled holes of the right headboard leg (#2R)
and the left headboard leg (#2L).
II. Prepare 6 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the pre-drilled holes of the
right headboard leg (#2R) and the left headboard leg (#2L) and
secure those bolts using the Allen wrench (#D) to lock them with
the headboard (#1).
Page 5 of 7
Align the threaded ends of the 2 footboard feet (#5) with the predrilled holes on the bottom of the footboard (#4) and tighten by hand
until secured.
#F x 8 pcs
#G x 8 pcs
#H x 8 pcs
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
I. Insert 4 threaded studs (#F)
into the right headboard leg
(#2R) and the left headboard
leg (#2L).
II. Insert one side rail (#6) onto
the two threaded studs (#F)
on the right headboard leg
(#2R). Then insert 2 beveled
washers (#H) onto the 2
threaded studs (#F) and
secure with the 2 hex nuts
(#G) using the wrench (#I) to
tighten. Repeat the process
to secure the other side rail
(#6) onto the left headboard
leg (#2L).
III. Repeat the process above to
assemble the other ends of
the 2 side rails (#6) onto the
footboard (#4).
Page 6 of 7
Each slat (#7) has 2 slat support legs (#7). Align the threaded ends of
the 2 slat support legs (#8) with the pre-drilled hole of the slat (#7) and
tighten by hand until secured. Repeat the process to assemble the
remaining 6 slat support legs (#8) onto the remaining 3 slats (#7).
I. Align the ends of the assembled
slat (#7) with the pre-drilled holes
on each side of the side rails (#6).
II. Secure two screws (#J) onto each
end of the slat (#7) using a Phillips
screwdriver to tighten them down
to the side rails (#6). Repeat the
process for the remaining 3 slats
(#7).
III. Make sure the bed is rested on a
flat surface and does not feel loose
or wobbly. If it does, double check
that the bolts/screws are secured
and properly tightened.
Turn right (clockwise) to tighten
#J x 8 pcs
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
Page 7 of 7
Loading...