KeeLog SerialGhost DB-9, SerialGhost DB-25 User Manual

Download

SerialGhost Wi-Fi

User’s Guide

SerialGhost Wi-Fi

DB-9/DB-25 2 GB

Check http://www.keelog.com/ for the latest version of this document.

SerialGhost Wi-Fi

Table of contents

Getting started ................................................................................................................. 2

Introduction ...................................................................................................................... 3

About the product ......................................................................................................... 3

Features ....................................................................................................................... 3

Requirements ............................................................................................................... 3

Quick Start ....................................................................................................................... 4

Configuration ................................................................................................................. 10

Recording data............................................................................................................... 12

Viewing recorded data .................................................................................................... 13

Remote access .............................................................................................................. 15

Checklist .................................................................................................................... 15

Configuration .............................................................................................................. 15

E-mail reporting .......................................................................................................... 17

On-demand access ..................................................................................................... 18

Clock configuration ......................................................................................................... 21

Using KL Tools............................................................................................................... 23

Configuration files .......................................................................................................... 24

CONFIG.TXT .............................................................................................................. 25

TIME.TXT ................................................................................................................... 26

WIFI.TXT.................................................................................................................... 27

Specifications ................................................................................................................. 29

Troubleshooting ............................................................................................................. 30

Legal disclaimer ............................................................................................................. 32

Getting started

Already familiar with SerialGhost data loggers?

 Make your logger go on-line in a few simple steps: section Quick Start

New to SerialGhost data loggers?

 First, configure the logger: section Configuration  Then learn about recording data: section Recording data  Then, retrieve the recorded data: section Viewing recorded data  Finally, get the most out of your Wi-Fi data logger by configuring WLAN

communications: section Remote access

Questions or problems?

 Go through the Troubleshooting section.

SerialGhost Wi-Fi

Introduction

About the product

The SerialGhost Wi-Fi is a compact RS-232 and serial bus logger with a memory capacity of 2GB, that may be accessed locally as a USB Flash Drive, or remotely through Wireless LAN. Bidirectional data flowing through the serial bus will be captured and stored on the internal Flash Drive in a special file. This data may be retrieved by switching to Flash Drive mode, giving instant access to all captured data. The Wireless LAN functionality allows receiving logged data as E-mail reports, and on-demand via the local TCP/IP network. The SerialGhost Wi-Fi also features a built-in time-stamping module and battery. This enables it to add time and date information to the log file. Thanks to the internal battery, the time and date persist even when the device is not powered. The SerialGhost Wi-Fi does not require any dedicated software or drivers.

Features

 Logs asynchronous serial transmission (RS-232 compatible)  Baud rates up to 115200 bps  Logs 2 streams simultaneously (RX and TX)  2 Gigabytes internal memory  Powered from a USB port, or external power supply  No software or drivers required, Windows, Linux, and Mac compatible  USB Flash Drive mode  Background connection to the Internet over a local Access Point  Automatic E-mail reports with recorded data  On-demand access at any time through TCP/IP  Support for WEP, WPA, and WPA-2 encryption  Time and date stamping  Built-in battery

Requirements

 Asynchronous serial bus with RS-232 logic levels (+/-12V)  Operating system with USB Mass-Storage device support  5V DC power source (external power supply, or USB port)  Wi-Fi compliant Access Point coverage (WPA-2, WPA, WEP64/128, or open network)  Optionally MS Windows XP/Vista/7/8 (only for running KL Tools)

SerialGhost Wi-Fi

Quick Start

This section contains concise information on basic operation of the SerialGhost Wi-Fi. If you need detailed instructions, please refer to sections Configuration, Recording data, and

Viewing recorded data.

Before you start, make sure you have the following information about the serial bus you want to log data from:

 Baud rate (bits per second)  Number of bits per transfer (usually 8)  Parity bit configuration (usually not used)  Number of stop bits per transfer (usually 1)

Step 1. Open a text editor (such as Notepad) and create a file named CONFIG.TXT. This file will later be used to configure the device. Use the following template:

Baudrate=9600 Bits=8 Parity=None

StopBits=1

Replace Baudrate with the actual baud rate in bits per second of the serial bus you want to log data from. Replace Bits with the number of bits per transfer (5…8). Provide the parity check using one of the following strings: None, Even, Odd, Space, or Mark. Replace StopBits with the number of stop bits per transfer (1, 1.5, or 2).

Finally, save the configuration file as CONFIG.TXT.

SerialGhost Wi-Fi

Step 2. Connect the serial logger and enable Flash Drive mode.

Take the supplied USB cable and connect it to the mini-port on the logger’s side. Connect the USB cable to a free USB port using the supplied red USB Key.

After a few seconds, the SerialGhost will automatically get detected as a mass storage device, and pop up as a removable drive.

Step 3. Copy the configuration file CONFIG.TXT to the logger’s Flash Drive.

Then, safely remove the device, and disconnect it from the USB port. Disconnect the USB cable as well.

SerialGhost Wi-Fi

Step 4. To start logging, connect the logger in-line on a serial bus, powering the device through the mini USB port.

The device may be powered from a standard USB port. Do not use the red USB key. Alternatively, an external +5V DC (min. 200 mA) power supply may be used to power the

device through the mini-USB port (cell phone chargers with USB connectors are well suited for this).

Step 5. To retrieve the logged data, enable Flash Drive mode using the red USB Key, just like in step 2. A removable drive will pop-up, containing the file LOG.TXT with recorded data.

The upstream data (TX) and downstream data (RX) will be differentiated by the markers [1] and [2] interleaved in the log file.

SerialGhost Wi-Fi

Step 6. To configure the Wireless LAN connection, make sure you have the following data about the Wi-Fi network the device will operate in:

 WLAN Access Point ID (SSID)  WLAN encryption type (WPA-2, WPA, WEP64/128, or open network)  WLAN encryption password

Make sure you also have an E-mail address the logger can send reports to. Open a text editor (such as Notepad) and create a file named WIFI.TXT. This file will later be

used to configure the device. Use the following template:

WiFiNetwork=MyNetwork WiFiPassword=MyPassword WiFiEncryption=WPA2

Recipient=john@smith.com

Replace MyNetwork with the Access Point ID (SSID). Replace MyPassword with the WLAN password. Provide the encryption type using one of the following strings: WPA2, WPA, WEP64, WEP128, or None. Provide the E-mail address you would like to receive reports to after the Recipient string. Make sure you provide all strings in a case-sensitive manner.

Finally, save the configuration file as WIFI.TXT.

Step 7. Enable Flash Drive mode, as in step 5, and copy the configuration file WIFI.TXT to the Flash Drive.

SerialGhost Wi-Fi

Then, safely remove the device, and disconnect it from the USB port.

Step 8. On the next power-up, the logger will automatically connect to the Access Point defined in WIFI.TXT, and send an E-mail report to the specified recipient address every hour. Besides logged data, the report will contain Access Point information, IP configuration, and time-stamps.

SerialGhost Wi-Fi

Step 9. If E-mail reporting is not enough, you can take full control over the device from any computer in your Local Area Network. Install the supplied application KL Tools, add the logger to the list by its IP number, and explore the available features.

Using KL Tools you can communicate with multiple SerialGhosts, allowing creating entire networks of wireless data loggers. This solution is particularly recommended for monitoring several devices in a system with a large number of devices using serial buses, such as RS-

232. To read more on KL Tools, jump to section Remote access.

SerialGhost Wi-Fi

Configuration

The SerialGhost Wi-Fi may be configured through the file CONFIG.TXT, placed in the Flash Drive root folder. Use any text editor to prepare such a configuration file, containing the following text:

Baudrate=9600 Bits=8 Parity=None StopBits=1

Copy this file to the root folder in Flash Drive mode. The new configuration will be loaded on next power-up.

The following list presents the most common configuration options. All variable and value strings are case insensitive.

Baudrate sets the baud rate in bits per second of the monitored serial bus. Range is 300 bps to 115,200 bps. Default value is 9600.

Bits sets the number of bits per transfer of the monitored serial bus. Possible values are 5, 6, 7, 8. Default value is 8.

Parity sets the parity bit type of the monitored serial bus. Possible values are None, Even, Odd, Space, Mark. Default value is None.

StopBits sets the number of stop bits per transfer of the monitored serial bus. Possible values are 1, 1.5, 2. Default is 1.

Timestamping configures the built-in time- and date-stamping module, available in the SerialGhost TimeKeeper only. Allowed values are Yes (timestamping enable) and No (timestamping disabled). Default is Yes.

SerialGhost Wi-Fi

TimestampInterval sets the interval of serial bus inactivity in seconds, that will trigger a new time-stamp being logged. Range is 1 second to 9999 seconds. Default value is 10.

DisableLogging allows to disable logging. Allowed values are Yes (logging disabled) and No (logging enabled). Default value is No.

Encryption enables flash disk encrypting. Encryption will ensure full confidentiality of the stored data, even if the device is physically tampered with. Allowed values are Yes (encryption enabled) and No (encryption disabled). Default is No.

Important: toggling the encryption setting will format the entire flash disk. All data will be lost, including the configuration file!

Password sets the 3-letter password for remote access over TCP/IP (for example using KL Tools). Any three-letter combination is allowed (sequence and case are irrelevant). Default value is KBS.

LogMode sets the logging mode. Possible values are Ascii (data is logged as ASCII), Hex (data is logged as hexadecimal numbers), Dec (data is logged as decimal numbers). Default value is Ascii.

Separator sets the separator character between data values in logging mode Dec/Hex. Possible values are None, Space, Comma, Tab, Newline. Default is Space.

LogStream configures which serial stream are to be logged. Possible values are Both (both RX and TX get logged), Rx (only Rx is logged), Tx (only Tx is logged). Default is Both. If the mode is set to Both, the [1] and [2] markers will be used to differentiate between streams.

A full list of parameters is available in section Configuration files.

SerialGhost Wi-Fi

Recording data

Record mode is the default mode of operation for the SerialGhost Wi-Fi data logger. In record mode, the device will silently monitor the bidirectional data flow on the serial bus and store the captured data on the internal Flash Drive in file LOG.TXT.

The SerialGhost Wi-Fi must first be configured to the appropriate serial bus parameters, such as baud rate. Refer to section Configuration for detailed instructions.

Installation of the SerialGhost Wi-Fi in record mode is quick and easy, no software or drivers are required. Simply plug it in-line on the serial bus, using the DB-9 or DB-25 connectors. The device may be powered from a standard USB port, using the supplied cable. Alternatively, an external +5V DC (min. 200 mA) power supply may be used to power the device through the mini-USB port (cell phone chargers with USB connectors are well suited for this).

SerialGhost in record mode powered from a

USB port.

SerialGhost in record mode powered by an

external 5V DC (min. 200mA) power supply.

SerialGhost Wi-Fi

Viewing recorded data

Once serial data has been recorded, it may be retrieved on any computer with a USB port. This is done by switching to Flash Drive mode. Take the supplied USB cable and connect it to the mini-port on the logger’s side. Connect the USB cable to a free USB port using the supplied red USB Key.

After a few seconds, the SerialGhost Wi-Fi will automatically get detected as a mass storage device, and pop up as a removable drive. The operating system will use the standard built-in mass storage driver (MS Windows 7 in the following examples).

Depending on the drive letters available, the device will be visible as a new drive, for example F:. Use the systems file manager to browse this disk (for example Explorer).

SerialGhost Wi-Fi

The removable disk will contain the file LOG.TXT with a text log of all captured data. The data is stored in the same format as appearing on the serial bus, without any encoding. The upstream data (TX) and downstream data (RX) will be differentiated by the markers [1] and [2] interleaved in the log file. The SerialGhost Wi-Fi will also interleave time-stamps. The file LOG.TXT can be viewed and searched with any text editor, such as Notepad or MS Word.

Switching back to record mode can be achieved by a safe software removal of the flash disk. Use the systems standard disk removal procedure. For MS Windows, left-click on the Safe

Removal icon in the system tray and select the appropriate drive. Then reconnect the SerialGhost to the USB port, however without the supplied USB Key.

To get the most out of the SerialGhost, install the supplied application KL Tools. Go to section

Using KL Tools to find out more.

SerialGhost Wi-Fi

Remote access

This section guides through enabling E-mail reporting and TCP/IP access for the SerialGhost Wi-Fi data logger.

Checklist

Before you start, make sure you have the following data about the Wi-Fi network the logger will operate in:

 WLAN Access Point ID (SSID)  WLAN encryption type (WPA-2, WPA, WEP64/128, or open network)  WLAN encryption password

Make sure you also have an E-mail address the wireless logger can send reports to. Finally, to make the configuration process as simple as possible, install the supplied application KL Tools. The installation process is straightforward, just follow the wizard and answer a few standard questions.

Configuration

The SerialGhost Wi-Fi can be configured and operated entirely from KL Tools. Launch the application, select the device model, and choose to configure your device. The application will first display a serial bus configuration dialog, and then a time configuration dialog. If changing the default password, memorize or note the new values, otherwise access to the internal memory will not be possible. If unsure about a certain configuration option, leave the default value.

SerialGhost Wi-Fi

Serial bus configuration

Time-stamping module configuration

Finally, a Wi-Fi configuration dialog will be shown. Enter the data allowing the logger to connect to the WLAN Access Point:

 WLAN Access Point ID (SSID)  WLAN encryption type  WLAN encryption password

Remember, that these strings are case-sensitive. If the WLAN Access Point does not allow Auto-IP

configuration through DHCP, provide a static IP address, network mask, gateway address, and DNS information.

To receive E-mail reports containing serial data, supply your E-mail address. You may adjust the reporting interval and report size.

When finished, make sure the device is connected as in record mode. KL Tools will automatically create configuration files (CONFIG.TXT, TIME.TXT, WIFI.TXT), prompt for enabling Flash Drive mode, and copy the files to the loggers Flash Drive.

SerialGhost Wi-Fi

E-mail reporting

The SerialGhost Wi-Fi will send E-mail reports to the specified recipient address, by default every hour. Besides logged data, the report will contain Access Point information, IP configuration, and time-stamps.

The report size and interval may be set by configuring the logger through the file WIFI.TXT. Use KL Tools to do this, or view section Configuration files.

SerialGhost Wi-Fi

On-demand access

The SerialGhost Wi-Fi offers on-demand access via TCP/IP from any computer connected to the network. This feature is usually limited to the Local Area Network, unless your local network segment is visible globally. To access the logger remotely, launch KL Tools, select the proper device version, and navigate through the wizard to remote access. The Wi-Fi Control Center will be shown.

A remote device needs to be added first. This can be done by clicking the Add Device icon, and supplying the IP address, name (optional), and device password. The password must match the local 3-character combination defined in the devices CONFIG.TXT (K, B, S by default).

The IP address of the remote device can be obtained in a few ways:

 from an E-mail report (see section E-mail reporting)  from the device configuration (if using static IP)  from the Access Point configuration (if using Auto-IP)

If the IP address is unknown, the Search Local Network option can be used. This feature will send a broadcast signal to all devices in the Local Area Network, to which remote loggers

SerialGhost Wi-Fi

should respond. Make sure that no firewall blocks UDP communication, otherwise the procedure will fail.

Once a remote device is added, the log may be retrieved using the Download Log option.

If interested in other parts of the remote log file than the most recent 50 kB, use the Download Log Chunk option. This will display a dialog, allowing downloading any part of the remote log file.

SerialGhost Wi-Fi

KL Tools offers a wide variety of options, available at a single mouse-click:

 E-mail and WWW search  Encoding and layout conversion  Document searching  Document exporting  Communication with remote device  Multiple device handling

232.

SerialGhost Wi-Fi

Clock configuration

It is necessary to configure the built-in clock module for getting correct date and time-stamps. This task can be performed by KL Tools (recommended), or can be done manually.

To configure the internal clock using KL Tools, launch the application, select the device model, and choose to configure the device. The application will display a time and date configuration dialog. Make sure date and time stamping is enabled, and that the Set time and date checkbox is clicked. Select the desired time format, and move to the succeeding dialogs.

KL Tools will guide you through enabling Flash Drive mode, and placing the configuration file TIME.TXT on the internal flash disk.

The clock can also be configured manually, without using KL Tools. To do this, a text file named TIME.TXT should be prepared with the following format:

Year=2010 Month=4 Day=1 Hour=12 Minute=34 Second=56 Format=PM

The fields should contain the current time and date. The field Format allows distinguishing between A.M., P.M., and 24-hour time (use the value AM, PM, or 24). After the file has been prepared, switch to Flash Drive mode and copy the file TIME.TXT to the root folder of the flash disk. The USB Key delivered with the device has to be used to switch to Flash Drive mode.

SerialGhost Wi-Fi

After copying the file, safely remove the Flash Drive. The new clock configuration will be loaded on next power-up.

The clock configuration file must be named TIME.TXT and must be placed in the root folder. Variable and value strings are case insensitive, however they must match the options listed below.

 Year sets the clock year value. Valid range is from 2000 to 2099.  Month sets the clock month value. Valid range is from 1 (January) to 12 (December).  Day sets the clock day value. Valid range is from 1 to 31. If the specified day exceeds

the maximum number of days in the specified month, the next valid day value will be chosen.

 Hour sets the clock hour value. Valid range is from 1 to 12 for 12-hour time

(A.M./P.M.), and 0 to 23 for 24-hour time.

 Minute sets the clock minute value. Valid range is from 0 to 59.  Second sets the clock second value. Valid range is from 0 to 59.  Format sets the time format. Valid values are AM, PM, and 24. If AM is chosen, the 12-

hour format is selected and the specified hour is treated as before noon. If PM is chosen, the 12-hour format is selected and the specified hour is treated as after noon. If 24 is chosen, the 24-hour format is selected and the specified hour is treated as 24hour format.

Sample TIME.TXT for 12-hour time:

Year=2010 Month=10 Day=25 Hour=5 Minute=51 Second=43 Format=PM

Sample TIME.TXT for 24-hour time:

Year=2010 Month=10 Day=25 Hour=17 Minute=51 Second=43 Format=24

SerialGhost Wi-Fi

Using KL Tools

KL Tools is a free application delivered with all SerialGhost series devices. KL Tools assists in configuring a SerialGhost and retrieving the recorded data it contains. It is not necessary to operate the device, but may speed up usage by its intuitive user interface.

KL Tools is available on the CD-ROM attached with the device. Installing KL Tools is straightforward. Simply follow the installation wizard and answer standard questions. When initialized, KL Tools will ask for the device type, and assist in configuring the device and retrieving the recorded images. There is no special knowledge required to use KL Tools – simply follow the instructions displayed by the application.

SerialGhost Wi-Fi

Configuration files

The SerialGhost Wi-Fi is configured via three text files placed on the internal Flash Drive:

 CONFIG.TXT (configures serial bus parameters)  TIME.TXT (configures the internal clock for time-stamping)  WIFI.TXT (configures Wi-Fi functionality)

These files should contain configuration parameters, placed in successive lines in the following format:

Parameter1=Value Parameter2=Value Parameter3=Value

…

Example of WIFI.TXT

WiFiNetwork=MyNetwork WiFiPassword=MyPassword WiFiEncryption=WPA2

Recipient=john@smith.com

These configuration files must be placed in the device internal memory using Flash Drive mode.

Device configuration can be performed by KL Tools, or manually by the user. KL Tools performs the same operation as would be done manually, that is creates the configuration files, requests switching to Flash Drive mode, and copies the files to the flash disk.

Creating configuration files manually may be necessary on systems not supported by KL Tools, such as Mac OS or Linux.

SerialGhost Wi-Fi

CONFIG.TXT

The file CONFIG.TXT is responsible for configuring serial bus parameters.

Parameter

Values

Example

Description

Baudrate

Baud rate in bps (default 9600)

Baudrate=115200

Serial bus baud rate in bits per second (300…115200).

Bits

5 6 7 8 (default)

Bits=7

Number of bits per transfer on the monitored serial bus.

Parity

None (default) Even Odd Space Mark

Parity=Even

Type of parity bit on the monitored serial bus.

StopBits

1 (default)

1.5 2 Parity=1

Number of stop bits per transfer on the monitored serial bus.

Timestamping

Yes (default) No

Timestamping=Yes

Time-stamping disable flag.

TimestampInterval

Timestamp interval in seconds (default 10)

TimestampInterval=1

Interval of bus inactivity which will result in a time-stamp being added.

DisableLogging

Yes No (default)

DisableLogging=Yes

Data logging disable flag.

Encryption

Yes No (default)

Encryption=No

Flash drive encryption setting (caution: changing this value will re-format the flash drive).

Password

3-character password (default KBS)

Password=SVL

Three-character combination for accessing the device over TCP/IP (for example using KL Tools).

Separator

None Space (default) Comma Tab Newline

Separator=Comma

The separator between data values in Dec/Hex modes.

LogMode

Ascii (default) Hex Dec

LogMode=Hex

Data format in log file.

LogStream

Both (default) Rx Tx

LogStream=Tx

Selection of serial data streams to be logged.

SerialGhost Wi-Fi

TIME.TXT

The file TIME.TXT is responsible for configuring the built-in real-time clock.

Parameter

Values

Example

Description

Year

Year value (range 2000…2099, default 2010)

Year=2010

Year setting (range 2000 to 2099).

Month

Month value (range 1…12, default 1)

Month=10

Month setting (1 is January, 12 is December).

Day

Day value (range 1…31, default 1)

Day=15

Day setting (range 1 to 31).

Hour

Hour value (range 1…12 or 0…23, default 1)

Hour=6

Hour setting (range 1 to 12 for A.M./P.M. format and 0 to 23 for 24-hour time).

Minute

Minute value (range 0…59, default 0)

Minute=37

Minute setting (range 0 to 59).

Second

Second value (range 0…59, default 0)

Second=49

Second setting (range 0 to 59).

Format

AM PM (default) 24

Format=24

Time format setting. If AM is chosen, the 12-hour format is selected and the specified hour is treated as before noon. If PM is chosen, the 12-hour format is selected and the specified hour is treated as after noon. If 24 is chosen, the 24hour format is selected and the specified hour is treated as 24-hour format.

SerialGhost Wi-Fi

WIFI.TXT

The file WIFI.TXT is responsible for configuring Wireless LAN and TCP/IP functionality. The following tables summarize the available parameters.

Basic parameter list

Parameter

Values

Example

Description

WiFiNetwork

SSID string (no default)

WiFiNetwork=MyWiFi

Access Point ID (SSID), casesensitive. If omitted, Wi-Fi functionality will be disabled.

WiFiEncryption

None (default) WEP64 WEP128 WPA WPA2

WiFiEncryption=WPA2

Access Point encryption type. If omitted, Wi-Fi functionality will be disabled.

WiFiPassword

Password string (no default)

WiFiPassword=MyPass

Access Point password, case sensitive. If open network, skip this parameter.

IpAddress

IP address string (no default)

IpAddress=192.168.0.100

Static IP address of device. Skip this parameter if using Auto-IP.

NetMask

Network mask string (no default)

NetMask=255.255.255.0

Network mask of device. Skip this parameter if using Auto-IP.

Gateway

Gateway address string (no default)

Gateway=192.168.0.1

Default gateway. Skip this parameter if using Auto-IP.

DnsServer

First DNS address string (no default)

DnsServer= 216.231.41.2

First DNS. Skip this parameter if using Auto-IP.

DnsServer2

Second DNS address string (no default)

DnsServer2= 206.124.64.1

Second DNS. Skip this parameter if using Auto-IP.

Recipient

E-mail recipient string (no default)

Recipient=john@server.com

Recipient E-mail address for Email reporting. If omitted, reporting will be disabled.

ReportInterval

Interval value (min. 600 sec. or 3600 sec., default 3600 sec.)

ReportInterval=7200

Interval for E-mail reporting in seconds. Minimum interval is 600 seconds (10 minutes) for custom SMTP server, and 3600 seconds (1 hour) for default server.

ReportSize

Size value (max. 102400 bytes, default 10240 bytes)

ReportSize=20000

E-mail report size in bytes.

DisableWiFi

Yes No (default)

DisableWiFi=Yes

Wi-Fi disable flag.

SerialGhost Wi-Fi

Advanced parameter list (use only when you know what you’re doing!)

Parameter

Values

Example

Description

WiFiStandard

US (default) Canada Europe Spain France Japan

WiFiStandard=Europe

Standard for Wi-Fi operation. Select the region that fits best.

DisableTcp

Yes No (default)

DisableTcp=Yes

TCP disable flag. Disables ondemand access through TCP/IP.

TcpPort

Port value

(0…65535, default

25999)

TcpPort=12345

TCP communication port. Must match setting in KL Tools.

DisableUdp

Yes No (default)

DisableUdp=Yes

UDP disable flag. Disables answering to broadcasted network searches.

UdpPort

Port value

(0…65535, default

25998)

UdpPort=23456

UDP communication port. Must match setting in KL Tools.

DisableSmtp

Yes No (default)

DisableSmtp=No

SMTP disable flag. Disables Email reporting.

CustomSmtp

Yes No (default)

CustomSmtp=Yes

Custom SMTP flag. Enables user defined SMTP server.

SmtpServer

Server string (no default)

SmtpServer=smtp.mail.com

Custom SMTP server. Defines user SMTP server address.

SmtpUser

User string (no default)

SmtpUser=John

Custom SMTP user. Defines user SMTP user name.

SmtpPassword

Password string (no default)

SmtpPassword=MyPass

Custom SMTP password. Defines user SMTP password.

SmtpSender

Sender string (no default)

SmtpSender=John Smith

Custom SMTP server. Defines user SMTP sender string.

SmtpPort

Port value

(0…65535, default

25)

SmtpPort=25

Custom SMTP communication port.

Sample Wi-Fi configuration files:

No encryption, Auto-IP

WiFiNetwork=MyWiFi

Recipient=john@server.com

WPA-2 encryption, static IP

WiFiNetwork=MyNetwork WiFiPassword=MyPassword WiFiEncryption=WPA2

IpAddress=192.168.0.100 NetMask=255.255.255.0 Gateway=192.168.0.1 DnsServer= 216.231.41.2 DnsServer2= 206.124.64.1

Recipient=john@smith.com

SerialGhost Wi-Fi

Specifications

Power supply

4.5 V – 5.5 V DC

Max. power consumption

220 mA (1.1 W)

Maximum continuous log speed (approx.)

15 kB/s (both streams)

Memory capacity

2 GB

Data retention

100 years

Device support

Asynchronous serial devices operating at RS-232 logic levels (+/-12V)

Maximum log read speed

150 kB/s

Access Point support

Wi-Fi CERTIFIED™ devices

WLAN encryption support

WPA-2, WPA, WEP64, WEP128

WLAN range

150 m (165 yards) in open terrain, approx. 50 m (55 yards) through one concrete wall

Dimensions including connectors (L x W x H)

DB-9 version

DB-25 version

62 mm x 31 mm x 16 mm (2.4" x 1.2" x 0.6")

62 mm x 54 mm x 16 mm (2.4" x 2.1" x 0.6")

All KeeLog products come with 1 year warranty against manufacturer defects. Defect products must be shipped by the customer. All warranty repairs and delivery to the customer will be paid by the manufacturer.

SerialGhost Wi-Fi

Troubleshooting

The SerialGhost will not work with the following hardware configurations:

1. Synchronous serial buses

2. Devices operating at speeds higher than 115,200 bps

3. Serial buses using logic levels different than +/-12V

4. Serial devices using non-standard DB-9 or DB-25 pinouts

5. SPI, I2C, TWI, USB, PS/2, SATA, FireWire, etc. buses

6. Non Wi-Fi-conformant Access Points (Wi-Fi CERTIFIED™)

The SerialGhost does not switch to Flash Drive mode

Please check the following:

1. Are you using the delivered USB Key to connect the device to a USB port?

2. Does the operating system support removable USB flash disks?

3. Have you checked the drive list?

4. Have you tried on a different USB port?

5. Have you checked on a different computer?

I can’t find any data after switching to Flash Drive mode

Please check the following:

1. Have you powered the device from the USB port while recording?

2. Did you properly configure the device through CONFIG.TXT?

3. Have you actually transmitted any data over the serial bus while recording?

The SerialGhost always shows up as a removable drive

Connect the USB plug directly to a USB port, without the USB Key.

I’m not receiving E-mail reports

Please check the following:

1. Have you configured Wi-Fi access by using KL Tools or creating WIFI.TXT manually?

2. Have you provided a valid recipient E-mail address? Are you checking the recipient mailbox?

3. Is the Access Point ID (SSID) set correctly? Remember, that it is case-sensitive.

4. Have you configured the encryption type and password correctly (case-sensitive)?

5. Is the remote device within WLAN range? Is the signal strong enough? Please verify this by using a second WLAN device located in the same position.

6. Does the Access Point configuration allow Auto-IP? If not, please provide a static IP configuration.

SerialGhost Wi-Fi

I cannot retrieve the log using KL Tools

Please check the following:

1. Have you added the remote device to the device list in KL Tools by providing its IP address?

2. Has the remote device established a connection to the Access Point? Check if you are receiving E-mail reports.

3. Have you performed a communication test? Right-click on the device in KL Tools and select Test Communication.

4. Have you performed a network search? Run a network search from KL Tools.

5. Is a firewall blocking communication? Check if the TCP and UDP ports (default 25999 and 25998) are available for communication.

6. Have you provided the correct 3-character combination? The remote device configuration must match the data entered in KL Tools (default values are KBS or KBD).

7. Is the remote device located in the same LAN segment as the host computer? If not, TCP/IP communication will not work.

Problems with time-stamps

Set the correct time by creating a clock configuration file TIME.TXT. Make sure you have not disabled time-stamping. Refer to the Clock configuration section for detailed instructions.

Can I run KL Tools on Mac OS or Linux?

KL Tools is currently only available for MS Windows. For configuring the device under Mac OS or Linux, the configuration files CONFIG.TXT, WIFI.TXT, and TIME.TXT must be created

manually, using a text editor.

I’ve checked everything, nothing helps!

If you are still experiencing problems, please do the following:

1. Check if the problem appears with a different baud rate and serial bus configuration.

2. Check if the problem appears with a different serial bus driver.

3. Check if the problem appears using a different USB port.

4. Contact the dealer you have purchased the device from. Please supply all necessary information (hardware type, model and manufacturer, OS type and version, and a short description of the problem).

SerialGhost Wi-Fi

Legal disclaimer

KeeLog does not take responsibility for any damage, harm or legal actions caused by misuse of its products. The user should follow the guidelines contained in this document, otherwise no liability will be assumed. It is the user's responsibility to obey all effective laws in his/her country, which may prohibit usage of KeeLog products. Please also consider, that not knowing the law does not allow to not obeying it. A good example is the U.S. Department of Justice Letter on Keystroke Monitoring and Login Banners, according to which a clear notice should be displayed, warning that user keystrokes may be logged. Please check with your legal representative for logging requirements in your country.

For more information on KeeLog products,

visit our website:

http://www.keelog.com/

You should not use this device to intercept

data you are not authorized to possess,

especially passwords, banking data,

confidential correspondence etc. Most

countries recognize this as a crime. Please

consult a legal representative for logging

requirements in your country.

SerialGhost Wi-Fi

Notes:

European Office KeeLog

Lekcyjna 42 PL 51-169 Wroclaw Poland

http://www.keelog.com/ keelog@keelog.com

U.S. Office Aqua Electronics

1550 Louis Ave. Elk Grove Village, IL. 60007 U.S.A

RoHS

KeeLog SerialGhost DB-9, SerialGhost DB-25 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual