Page 1
6-stage PHASER
with ramp
and
tap tempo
Keeley Phaser Specication
Power Consumption
Max Voltage ………………..…9Vdc
Avg. Current Draw………….50mA
Rates
Max Phase Time
*
……………..…20s
Min Phase Time…………….82ms
Max Ramp Time………….…….13s
Dimensions
Width
in [mm]
………………..3.7 [93]
Length
in[mm]
……………….4.6[118]
Weight
lbs
……………………………0.9
*Max phase time are only valid for knob mode.
Longer phase times are possible in tap mode.
Power only
on when
plugged in.
Power Settings
Pedal is still on in
bypass mode.
This pedal is designed to be used with
9Vdc baeries or a suitable power supply.
Power connecon should be negave on
the p and 9V on the sleeve (IBANEZ AC109).
Using voltage other than the rated one could
permanently damage this pedal.
Tap Tempo Mode Overview
see back for more info...
S
F
Tap
Rate
Edge
Tap tempo
Tap at least 2 mes
to set tempo
Turning this knob
defeats the tap.
Blinking rate Indicator
The tap tempo is engaged once a tempo is tapped in with
at least 2 taps. This causes the high rate light to turn on.
When the slow rate knob is moved, the tap tempo turns off.
Tap engaged
indicator.
Ramp Mode Overview
see back for more info...
S
F
Ramp
Slow Rate
Edge
Slow/fast
When switching, old light
stays on unl ramp is done.
Blinking rate Indicators
Although the rate knobs are labeled fast and slow, they are
idencal. The labeling was designed to give the knobs more
meaning than a simple number.
Slow on the ramp means the switch between rates takes longer
Fast Rate
S
F
S
F
Ramp
Introduction to the Keeley Phaser
Engineering the finest in
Customer Service!
Some Nice Settings
What is an edge knob anyway?
Sometimes when working on an effect,
there are controls that really do great
things to the sound of your guitar but
don’t really conform to the traditional
labels. Should we discriminate against
these controls? Should we call them
what they are not? We say no!
Our edge knob is two things…
One part depth control, changing the
phase from a more subtle effect, to one
that is full out spacey as the knob
moves clockwise.
The other part is envelope filter,
changing where the signal is phased the
hardest. At the farthest setting clockwise, your highs are most enhanced.
When turned fully counter-clock, the
low end of your phaser gets the boost .
S
F
Ramp
Slow Rate
edge
Fast Rate
S
F
S
F
Ramp
S
F
Ramp
Slow Rate
edge
Fast Rate
S
F
S
F
Ramp
The ramp is set to be a fairly quick change
between the fast and slow. The Fast
control will yield an almost organ like
sound. The slow is a very nice subtle
phase effect. We tried it aer our 4-knob
compressor and it sounded great!
These sengs feature a more agressive
fast rate, a longer ramp me and beefed
up edge. Great response from that ramp.
Use it oen!
Keeley
Electronics
Keeley
Electronics
First of all, thank you for purchasing a Keeley Electronics 6
stage Phaser. We have worked
hard to make a phaser with a
vintage sound without sacrificing the conveniences of more
modern pedals. This is an
analog pedal. The only
hybrid-digital circuitry we use
in it controls the flow of the
analog signal. But your guitar
tone is never sampled and
remains 100% analog
throughout the pedal.
Always
On
Selection Indicator
Page 2
Switch
Left
Tap Mode
Switch
Right
Rate Indicator
Tap Acve Indicator
Fast Indicator
Slow Indicator
Ramp
Slower
Ramp
Faster
Phase
Slower
Phase
Faster
ramp Mode
the slow light is
blinking and the fast
light off.
The old speed light is
now constant on... The
ramp position sets how
long the change to the
new speed takes.
Right after the Slow/Fast zpress!
Right before the speed switch
is engaged...
The ramp is DONE!
The old speed light is now
off. The new speed light
is blinking at the speed of
its knob.
Rate knob
is moved
Ta
p
T
ap
Right before the speed switch is pressed
Only one light blinks...
it’s rate is set by the
slow rate knob.
By pressing the ‘Tap
Tempo’ switch you
engaged the tap tempo .
The light on the right
shows this.
Tap Tempo switch is pressed...
Slow rate knob is moved...
By tapping the speed
switch you engaged the
tap tempo .
The light on the right
shows this.
Loading...