DVD Player User’s Manual
DVD - 3/DVD - 3T
3406100490B
is the prohibition mark. If this appears when you operate the
product, wait until it disappears. If this phenomena repeats, the
current button does not cope with the disk in play.
NOTICE:
For additional information or for the location of an authorized service center, please
contact KEC Mobile Applications / KTV USA, Inc. at (800) 524-1216 or (973) 470-9191
KTV USA, Inc. 1 Madison Street East Rutherford, NJ 07073 800 524-1216 / 973 470-9191
KTV USA, Inc. ©
2005
Preparations
Connection
Setup
Use
Others
HY-DVD3-COVER 2005.9.30 9:58 AM Page 2
2
Safety Precautions
Cautions are composed of Warning and Attention which mean
the followings respectively.
: Possibility of fatal injury or death
: Possibility of minor injury or product damage
Put the cigar jack into the
deepest point to prevent
shaking.
It may cause a poor contact or
fire.
Never use any damaged
cigar jack.
It may cause a poor contact or
fire.
Never touch the cigar jack
with wet hands.
It may cause a fire or electric
shock.
Never hold the product
with your hands while the
disk is in play.
It may cause a breakdown of
disk or product.
Be careful not to get the
cigar jack cable entangled.
It may cause an accident.
Do not expand the cigar
jack too severely.
It may cause the battery dis-
charge from instable voltage.
Grab the cigar jack firmly
to pull it out.
If not, it may cause a heat
emission or fire.
Watching or adjusting is
prohibited during drive.
It may cause a traffic accident.
Secure your vision from
the product.
It may cause a traffic accident.
Preparations
3
Don’t put books or waterfilled vessels.
It may cause a breakdown.
Don’t put metals(coin, hair
pin, ironware, etc.) or burnable foreign
materials(match, paper, etc.)
in the disk inlet or port hole.
It may cause a fire or electric
shock.
Put the product at a flat
and stable place.
Otherwise, It may cause a
wrong operation.
Neither use nor store ignitable
sprays or inflammable materials in the vicinity.
It may cause an explosion or fire.
Avoid the vicinity of the handle knob for installation.
It may cause a traffic accident.
Keep the remote control away
from the brake pedal.
It may cause a traffic accident.
Never disassemble or modify
the product on your own.
It may cause a breakdown.
Keep the volume reasonable.
It may cause an interfering other drivers
and being ignorant of surrounding situation.
What is dewing?
The DVD player may create humidity when it
is under sudden change of environment.
‘Dewing’ inside the DVD player may suspend
operation for 2 or 3 hours.
To prevent dewing?
Supply power and leave the product at a dry
place for more than 2 hours to eliminate the
internal humidity.
Dewing occurs when
You move to a warmer outdoor place from a
room or car which is well air-conditioned in hot
summer.
You move to a warm room from a cold outdoor place in winter.
Do read and use the followings carefully for your safety and product protection.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 2
4
Special Features
5
Preparations
Contents
Connection
Connecting to TV/Audio . . . . . . . . . . . . .15
Use
Disc Play(DVD, VCD, CD) . . . . . . . . . . .22
Checking DISPLAY . . . . . . . . . . . . . . . . .23
Checking disc Menu . . . . . . . . . . . . . . . . .23
Changing Disc Audio/Subtitle language
during the playback . . . . . . . . . . . . . . . . .24
Searching Video track/Music . . . . . . . . .25
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . .26
Repeat Play . . . . . . . . . . . . . . . . . . . . . . .27
Zooming-In/Angling . . . . . . . . . . . . . . . . .28
Searching Screen/Music . . . . . . . . . . . . .29
Playing MP3 and WMA Disc . . . . . . . . . .30
Photo View by JPEG Disc . . . . . . . . . . . .31
Others
TroubleShooting . . . . . . . . . . . . . . . . . . .32
Pro duct Sp ecifi catio n . . . . . . . . . . . . . . . .34
Reference .............................................35
Setup
Function Setup(Setup Menu)
. . . . . . . . . .1 6
LANGUAGE Setup . . . . . . . . . . . . . . . . .17
DISPLAY Setup . . . . . . . . . . . . . . . . . . . .18
AUDIO Setup . . . . . . . . . . . . . . . . . . . . . .19
LOCK Setup . . . . . . . . . . . . . . . . . . . . . . .20
OTHERS Setup . . . . . . . . . . . . . . . . . . . .21
Preparations
Safety Precautions.......................................2
Special Features .....................................4
Disc Information ......................................6
Disc Handling and Storage......................7
Parts Name & Description
(Front, Front
panel Display, Rear)................................8
Parts Name & Description (Remote Control
Battery Change)........................................
11
Parts Name & Description(Cautions for
Battery Handling)...................................11
Parts Name & Description
(Name and
Function of Remote Control Buttons).....12
Precautions for DC Input/
Output Port Use.....................................14
Checking Accessories...........................14
Covers DVD, VCD, SVCD, and CDDA
Covers play MP3, WMA, and
JPEG(i.e. CD-R, CD-RW, DVD-R,
DVD+R, DVD-RW, and DVD+RW disk
containing MP3, WMA, or JPEG)
OSD(On Screen Display)
Press [DISPLAY] to display the information on
the DVD/VCD/CD disk and the device.
Screen Saver
High Performance Video(27Mhz/10bit)
Coaxial Digital Output(PCM, Dolby
Digital, dts)
Dolby Digital Decoder is built in.
Composite Video Output(x1)
S-Video Output(x1)
Slow Forward and Reverse
Playback(DVD)
Fast Forward and Reverse
Playback(DVD)
Title, Chapter, and Time Search for
DVD and Track and Time Search for
VCD/CD
Various Screen Ratio(DVD)
4:3 Zoom(Pan and Scan), 4:3 General(Letter
Box), and 16:9 Wide(Wide)
Repeat Play(Title and Chapter for
DVD and Track and disc for VCD/CD)
Repeat Play of Specific Area(A-B)
Selective Play(DVD/VCD/CD)
Title or Chapter for DVD and Track for Video
CD/CD
Various Voice Language(DVD)
Up 8 Voice Languages.
The number of languages depends on the disc
for SVCD and VCD.
Various Open Caption Language(DVD)
Up 32 Open Caption Languages.
The number of languages depends on the disc
for SVCD and VCD.
Various Angle Screen(DVD)
Simultaneous Multi Screen at Various
Angles(The number of screens depends on
the disc.)
Screen Zoom
3D Sound Effect
3D Sound Effect Service
Free Volt
From 12V to 24V
HY-DVD3-ENG 2005.9.30 11:40 AM Page 4
7
Preparations
6
Disc Information
DVD(Digital Versatile Disc) is a disc with a maximum capability of 135 minutes
long image, 8 Disc Audio languages, and 32 Subtitle languages. It also has the
function of MPEG-2 type image compression and dolby digital 3D surround so that
you are able to bring a movie theater at home enjoying vivid image and clean
sound quality.
Both DVD player and disc have encoded country codes that you have to accord
with before use.
Other discs than specified above shall not be used for this device.
DVD, DVD-Audio, DVD-ROM, and CD-ROM with an incompatible area code shall not
be used for this device.
The area code for the player is written in the back.
Disc for Play
1
Dolby Digital Digital Audio Disk Stereo Disk
Broadcasting Method
MP3 Disc
Disk Type Disk Logo Saved Signal Disc Size
DVD VIDEO
DVD AUDIO
DVD-R
DVD+R
DVD-RW
DVD+RW
VCD
Audio + Video
Audio + Video
12 cm
12 cm
Audio
12 cm
CD
CD-R
CD-RW
Disc Handling and Storage
Even tiny scratch on the disc may affect the screen. Please take special care.
Disc Handling
Press the center holder to put a disc out of the case with
convenience.
Do not touch the disc surface but refer to the figure to
move a disc.
Do not stick paper or tape on a disc. It may be bent.
Do not leave fingerprint or dust on a disc. Be sure to check
and clean any before use.
Disc Handling
For a disc stained by fingerprints or dirty foreign materials,
wipe it out with neutral rinse and water and dry it with a soft
towel.
From inside to outside
•
Sudden temperature rise may dew the operating part or lens of a product, resulting in play failure.
If then, supply power and insert a disc 1 or 2 hours later.
•
Do not use chemicals such as thinner, benzene, commercial rinse, alcohol, or static electricity preventive
spray for LP at all times. This may hurt the disc.
•
Do not let dust or foreign materials on a disc.
•
Do not use broken or scratched discs.
Disc Storage
Without direct ray Good ventilation
Available for vertical
storage
HY-DVD3-ENG 2005.9.30 11:40 AM Page 6
9
Preparations
8
Parts Name & Description
Front
8
3
64
5
109
12
1 POWER
Turns on/off power.
2 PLAY
Plays discs.
3 Disc SLOT
Receives and discharges discs.
4 Remote Sensor
Receives signals at a remote control.
5 NEXT/BACK
Skips chapters or tracks.
6 EJECT
Takes out discs.
7 STOP
Stops disc operation.
8 Display Window
Shows the current condition of players or
discs.
9 VIDEO IN
Connects a video cable with a video input port
and a video output port of other device.
10 AUDIO IN
Connects an audio cable with an audio input
port and an audio output port of other device.
7
Front Panel Display
1 DVD/SVCD/VCD/CD/MP3
Displays the disc type inserted in the main
body.
2 Dolby Digital
Indicates the disc in play was recorded by
dolby sound effect.
3 ANGLE
Indicates the disc in play is being watched at
various angles.
4 ROTATE
Indicates a disc is rotating.
5 PLAY/PAUSE
Displays the current operation mode.
6 REPAT/ALL
Displays the current Repeat/Play mode.
7 TITLE/CHAPTER
Displays the title or chapter information on the
DVD disc in play.
8 VISION
Displays the information on vision and operation modes such as Play, Stop, DiscConfirmed, or No-Disc.
9dts
Indicates the disc in play was recorded by dts
sound effect.
10 PBC (Play Back Control)
Displays the PBC operation condition while
VCD plays.
4 6 75
1
3
10
1
9
1
8
2
HY-DVD3-ENG 2005.9.30 11:40 AM Page 8
11
Preparations
10
MATE & LOCK
VIDEO OUTS-VIDEO
REMOTE
SENSOR
OUTIN
R-LINK
AUDIO-L AUDIO-R DIGITAL OUT
DC 12-24V
This device complies with part 15 of the
FCC rules. Operation is subject to the
Following two conditions.
(1) This device may not cause harmful
Interference, and (2) This device must
Accept any interference that may cause
Undesited operation.
Class 1 Laser Product
Parts Name & Description
Rear
1 VIDEO OUTPUT
Connect a video cable with a video output port
and a video input port of other device.
2 AUDIO OUTPUT
Connect an audio cable with an audio output
port and an audio input port of other device.
3 DC INPUT
Use the cigar jack for connection.(extra)
4 DC INPUT
Use the DC power cable for connection.
5 R-LINK IN/OUT
Allows remote control of any KEC Mobile
Applications video product in the R-LINK
chain even if it is hidden from view.
6 EXTERNAL REMOTE CONNECTOR
Use the external remote control cable.
7 S-VIDEO
Connect the S-Video cable with the S-Video
output port and TV S-Video input port for the
better resolution.
8 VIDEO OUT
Connect the Video cable with the Video output
port and TV Video input port.
9 AUDIO OUT
Connect the Audio cable with the Audio output
port and TV or Receiver Video input port.
10 DIGITAL AUDIO OUT
Connect the DVD player with a compatible
Dolby Digital Receiver or Decoder or DTS
Receiver or Decoder.
4 5 6 7 8 9
10
1 2
3
Parts Name & Description
1. Push the battery lid in
the arrow direction to
open it.
2. Put batteries in, checking
their polarity.
(1.5V, AAAx2)
3. Push the battery lid
back in the arrow direction to close it.
➡➡
Remote Control Battery Change
Using Remote Control
The remote control can cover as long as 7m
from the DVD receiver and up to 30
˚
to the left
and right.
Cautions for Battery Handling
Poor battery use may cause battery liquid leak or corrosion.
Check the polarity when you put batteries in.
Never expose a battery to heat or fire. Never disassemble or short a battery.
Check if a dead battery is in the remote control.
Never combine batteries of different type. Do not leave an old battery when you put a new
battery in.
When you don't use the remote control for a long time, please take out all batteries to prevent
their corrosion.
In case of poor operation of the remote control or shorter operation distance, replace the
batteries.
In case of battery liquid leak, clean the liquid from the remote control and replace the batteries.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 10
13
Preparations
12
Parts Name & Description
Name and Function of Remote Control Buttons
1
3
7
8
11
12
14
15
18
22
23
24
27
28
17
2
4
5
6
9
10
13
16
19
20
21
25
26
29
1 POWER (also on the DVD-3 front panel)
Press to turn the DVD player ON/OFF.
POWER OFF automatically activates AUX inputs.
DVD-3T Only: Press repeatedly to cycle through
DVD → TV → AUX.
2 EJECT (also on the DVD-3 front panel)
Press to eject the disc.
3 S-TITLE
Use to choose and cycle through the available
subtitles. This function will only work if the disc
contains subtitles.
4 LANGUAGE
Use to cycle through soundtracks in various
languages. This function will only work if the disc has been recorded
with multiple language soundtracks.
5 ANGLE
Use to access various camera angles. This function will only works if
he disc has been recorded with multiple camera angles.
6 TITLE
Displays the titles on the disc under play.
7 MENU
Displays the menus of the disc being played.
8 MODE
Use to choose play or repeat mode.
9 VOLUME
Adjusts the audio output levels of the DVD-3 to equalize its output with other
program sources in the vehicle (VCP, Video Game, etc).
IMPORTANT NOTE:
If the DVD-3 Volume Control is set to “0”, no sound
will be heard regardless of the settings of any other system volume controls.
10 ZOOM
Zooms in on picture.
11 A - B
Repeats the selected segment.
12 GOTO
Use to go to the track or chapter of the DVD disc you want.
13 MUTE
Cuts off the sound.
14 STOP (also on the DVD-3 front panel)
Stops disc play.
DVD-3T Only: Erases TV channel from memory in TV mode.
15. PAUSE
CD: The audio will be paused.
DVD: Still frame mode. Press repeatedly to advance the picture frame
by frame.
DVD-3T Only: Starts automatic channel scan.
16. PLAY (also on the DVD-3 front panel)
Press to begin disc play.
DVD-3T Only: Adds the channel to memory.
17. PREVIOUS (also on the DVD-3 front panel)
Press once to go to the start of the current chapter (DVD) or track
(VCD, CD, MP3).
Press again to go to the start of the previous chapter/track.
18. FR
Press repeatedly to fast reverse through the disc from 2X to 100X
faster. Audio will be muted. (DVD)
19. NEXT(also on the DVD-3 front panel)
Press to advance to the next chapter or track.
20 FF
Press repeatedly to fast forward through the disc from 2X to 100X
faster. Audio will be muted. (DVD)
21 ARROW KEYS / CH+, CH- KEYS
Use to move through the desired menu.
DVD-3T Only: Use Up/Down to change channels & Left/Right to fine
tune channels.
22 ENTER
Use to choose the desired menu item.
23 SETUP
Press to display the DVD-3’s built-in SETUP Menus for Language, Video,
Audio and Parental Control.
24 SLOW BACK
Press repeatedly to slow reverse through the disc from 1/2X to 1/32X slower.
Audio will be muted.
25 DISPLAY
Moves to the title/track or chapter of a disc.
26 SLOW FORWARD
Press repeatedly to slow forward through the disc from 1/2X to 1/32X slower.
Audio will be muted.
27 NUMERIC BUTTONS
May be used to make direct selections from various menu screens.
DVD-3T Only: May be used for direct entry of the desired channel.
28 TV/AUX
Press to cycle between DVD →AUX playback.
DVD-3T Only: Press to cycle through DVD →TV → AUX.
29 NTSC/PAL
Press STOP button and then press NTSC/PAL button to select the
desired mode.
IMPORTANT NOTE:The DVD-3 is preset at the factory for NTSC
mode. Do not use this button unless you need to set the player for use
outside of the USA or other NTSC countries.
NOTE:
Buttons 1~2 & 14~20 are duplicated on the Tri-Mode Remote Controller (Part # RC9799 or RR9799) that is packaged with
all KEC MOBILE APPLICATIONS LCD Systems. The RC9799 or RR9799
llœœœœ
TRK/CHAP
√√√√ll
buttons also function as
Channel +/- buttons with the DVD-3T. (Please see the Reference Section of this manual for more information).
HY-DVD3-ENG 2005.9.30 11:40 AM Page 12
15
Connection
14
When using the AUX input port of the head unit
Connecting to TV/Audio
MATE & LOCK
VIDEO OUTS-VIDEO
REMOTE
SENSOR
OUTIN
R-LINK
AUDIO-L AUDIO-R DIGITAL OUT
DC 12-24V
This device complies with part 15 of the
FCC rules. Operation is subject to the
Following two conditions.
(1) This device may not cause harmful
Interference, and (2) This device must
Accept any interference that may cause
Undesited operation.
Class 1 Laser Product
Connect the audio cable to the Audio Output(L/R) port in the back of the
DVD player and the Audio Input port of the car stereo.
1
Connect the video cable to the Video Output(L/R) port in the back of
the DVD player and the Video Input port of TV.
2
DVD Player
Audio Cable
Connect the DC power supply cable to
the head unit power supply cable.
Connect to AV1 or AV2.
Remote Control Sensor
Attention : Do not use the DC power supply cable
while the car cigar jack cable is in use.
Wiring Diagram
DC Power
Supply Cable
Attention : Do not use the
cigar jack cable while the DC
power cable is in use.
Cigar Jack
Cable
Video Cable
TV A/V Cable
Do not use.
LCD TV (monitor)
Head Unit
When using the DC power supply cable(DC Power Supply Cable)
Connect the red cable port to ACC (DC 12V~24V) and the black one to the ground.
1
Use ➃of Page 10.
Precautions for DC Input/Output Port Use
When using the car cigar jack(Extra Goods)
Check if the car cigar jack output voltage is DC 12V ~ 24V before you put it in the
DC input port.
Use ➂of Page 10.
Please call the shop where you bought our product to buy other extra goods than
specified above.
Remote
Control
AAA
Cells
Faceplate Frame
Owner’s Manual
& Warranty Card
Mounting Sleeve
12V DC, A/V&
R-Link Cables
Remote IR
Sensor #RESMC
Mounting
Hardware
AC Adaptor
12V Cigar Plug
Adaptor
Option Accessories
Checking Accessories
2
HY-DVD3-ENG 2005.9.30 11:40 AM Page 14
17
Setup
16
Sets up the Menu language, Disc Audio, Subtitle languages recorded in a disc to see or hear a
language that you want to.
Menu Language
Selects the menu language for the DVD player
Disc Audio
Selects the Disc Audio language.
Disc Subtitle
Selects the Subtitle language.
Disc Menu
Selects the Disc Menu language.
Press [ENTER] button.
•
Setup process is complete.
•
Press SETUP button to escape from the default menu.
4
DVD Setup
Press [SETUP] button of the remote
control when a disc is not running
and press
➛➛❿❿
button to move to the
LANGUAGE Setup menu.
1
Press ❷button to enter the LANGUAGE
SETUP menu and press
❿❿
, and
❷
buttons to select a language.
2
LANGUAGE Setup
•
If the set menu language is not written on the disc, the menu is not displayed into the set
language.
Press [SETUP] button when a disc
is not running
•
The SETUP menu appears.
1
Press SETUP when a disc is not running to enter DVD and the following screen to preset
various menus will appear as follows. Here comes the information of display.
The default setting will be left unchanged by power on or off.
Press
➛➛ ❿❿
button to move to the SETUP menu.
•
It changes in the order of LANGUAGE ➝DISPLAY ➝AUDIO
➝
LOCK ➝OTHERS.
LANGUAGE Setup
You can set up Menu language, Disc Audio, Sub-title, and Disc Menu languages.
DISPLAY Setup
You can select Screen Size, Progressive Scan, or Broadcasting Method.
AUDIO Setup
You can set up the Audio Digital/Analog output method.
LOCK Setup
You can select the x-rating for minors.
OTHER Setup
You can set up various functions.
2
Press ❷button to enter the detailed menu, press ❿❿button
to enter a sub menu, and press
and ❷buttons to select
the sub menu.
3
Press [ENTER] button.
•
Setup process is completed.
4
Press SETUP button to exit the default menu.
•
Exits the default menu.
5
Function Setup
Using Setup Menu
•
Press ➛button to return to the previous menu during DVD
setup.
Refer to LANGUAGE of Page 17.
Refer to DISPLAY of Page 18.
Refer to AUDIO of Page 19.
Refer to LOCK of Page 20.
Refer to OTHERS of Page 21.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 16
19
Setup
18
Depending on the active Audio Speaker condition, you can set up as follows.
Dolby Digital Output
- Bitstream: When connecting with Dolby Digital Decoder
- PCM: When connecting 2CH Output
DTS Output
- Bitstream: When connecting with DTS Decoder
- PCM: When connecting 2CH Output
PCM Sampling Frequency
- 48 KHz: When the active AMP can not deal with the 96KHz signal
- 96 KHz: When the active AMP can not deal with the 96KHz signal
Digital Output
- On: When turning on Digital Output
- Off: When turning off Digital Output
Press [ENTER] button.
•
Setup process is completed.
•
Press SETUP button to exit the setup menu.
3
Press [SETUP] button of the remote control
when a disc is not running and press
➛➛ ❿❿
button to move to the AUDIOSetup menu.
1
Press ❷button to enter the AUDIO
Setup menu and press
❿❿
, and ❷
buttons to select the menu for setup.
2
AUDIO Setup
DVD Setup
Here are the display setup options.
TV Aspect Size
- 16 : 9: You can see the screen in the ratio of 16 : 9.
- 4 : 3: You can see the screen in the ratio of 4 : 3.
Display Mode
- Letterbox: You can see the full screen in the ratio of 16:9 but a black margin will
appear both on the top and at the bottom respectively instead.
- Panscan: You can cut both sides of the 16:9 screen to zoom in the central part.
Press [ENTER] button.
•
Setup process is completed.
•
Press SETUP button to exit the setup menu.
3
Press [SETUP] button of the remote control
when a disc is not running and press
➛➛ ❿❿
button to move to the DISPLAY Setup menu.
1
Press ❷ button to enter the DISPLAY
Setup menu and press ❿❿, and ❷
buttons to select a display.
2
DISPLAYSetup
HY-DVD3-ENG 2005.9.30 11:40 AM Page 18
21
Setup
20
PBC (Play Back Control)
This function is applicable to VCD 2.0 for the quick search
of a shot by using the menu recorded in a disc.
Auto Play
This function is applicable to the play of DVD to jump to the Watching Movie menu, ignoring
the initial ad or Root menu for disc play.
B.L.E
Darken the screen at night.
Load Default
Returns to the ex-work default.
Screen Saver
Screen Saver is used to prevent TV or monitor in use from being damaged.
When you stop or pause the DVD player for more than 3 minutes, the DVD logo screen will
start moving.
Last Play
Starts the playback from the point where the playback stopped before.
Press [ENTER] button.
•
Setup process is completed.
•
Press SETUP button to exit the setup menu.
3
Press [SETUP] button of the remote control
when a disc is not running and press
➛➛❿❿
button to move to the OTHER Setup menu.
1
Press ❷ button to enter the OTHERS
Setup menu and press ❿❿, and ❷
buttons to select an item for setup.
2
OTHERS Setup
DVD Setup
This function keep children off violent or erotic materials by setting the rating from 1 to 8.
For the disc without a proper rating, this function is not applicable.
Rating
- Rating 1,2: For every age(a disc free of obsceneness,
violence, drug, or insult)
- Rating 3: Under parents' instruction or recommendation, Improper for young kids(a
disc containing violence but free of plain obsceneness or drug)
- Rating 4,5: In the attendance of parents under the age of 13(a disc free of sexual
act or excessive violence)
- Rating 6: In the attendance of parents under the age of 17(a disc for adult contain-
ing insult, violence, sexual act, and drug)
- Rating 7,8: Over the age of 17 only(a disc for adult only containing playing sexual
act and excessive violence)
Password
- New Password: Input a new password.
- Confirm: Input a new password again.
Press [ENTER] button.
•
Setup process is completed.
•
Press SETUP button to exit the setup menu.
3
Press [SETUP] button of the remote control
when a disc is not running and press
➛➛❿❿
but-
ton to move to the LOCK Setup menu.
1
Press ❷ button to enter the Rating
Setup menu and press ❿❿, and ❷
buttons to select a rating.
2
LOCK Setup
•
For the disc without a proper rating, LOCK function is not applicable.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 20
23
Use
22
Checking DISPLAY
Press [DISPLAY] button.
DVD
The current title, chapter, time, disc audio language, subtitle language, camera, and 3D
sound effect will be displayed in the screen.
VCD
The current track, time, disc audio language, and 3D sound effect will be displayed in the
screen.
•
What is Title?
Refers to a movie file recorded in a DVD disc.
•
What is Chapter?
Refers to each chapter, a unit which classifies a movie file recorded in a DVD disc.
•
What is Track?
Refers to a unit or a music which divides a scene recorded in a VCD or CD list.
1
Depending on the disc type, the Voice Language/Closed Caption function operates.
This function is available only during play.
Checking Disc Menu
Press [MENU] button.
The menu in the disc will appear.
The menu differs by the disc.
Whenever you press MENU button, PBC will be turned on and off in turn.(VCD 2.0)
CD and VCD1.1 don't have this function.
For the disc containing Menu, you may select one out of the various menus as follows.
1
Press ❷, ❿❿, and ❷ buttons to move to an item and
press [ENTER] button.
2
DISC PLAY
Before playing a disc
Playing a disc
Check if the area code of your DVD player accord with that of a disc. If not, the disk won't operate.
Press [POWER] button.
1
Let the labelled side(containing no data) of a disc face up
and put the disc in.
•
The disc will automatically operate.
2
Stop(
) Button
Stops play.
Play(❿❿) Button
- Press ❿❿to play the point whose play was suspended before.
- Press
twice and press ❿❿again to play a disc from the beginning.
Pause(ll) Button
- Pauses play of a disc.
- Whenever you press this button, the screen will change one by one.
- Press ❿❿button again to replay the disc.
•
In 3 minutes after a disc is paused, the DVD player will automatically enter the Screen Saver mode to protect
your TV.
•
If you don't pull a disc out in 10 seconds after you press EJECT button to eject the disc, it will be automatically
loaded, eventually the disc will stop.
(DVD, VCD, CD)
HY-DVD3-ENG 2005.9.30 11:40 AM Page 22
25
Use
24
Searching Video track/Music
During disc play, use the following functions to search a video track or a music.
Quick Search of Screen/Song
(DVD, VCD, CD, MP3)
Press FR and FF and ( ) button in the remote control
during play.
DVD
The play speed will change x2 ➝x4 ➝x16 ➝x100 by pressing the button.
VCD/CD
The play speed will change x2 ➝x4 ➝x8 by pressing the button.
MP3
The play speed will change x2 ➝x4 ➝x8 by pressing the button.
Skipping Chapter(Track)
(DVD, VCD, CD, MP3)
Press BACKand NEXT
()
button in play.
When pressing Back( ) button,
it returns to the previous chapter.
When pressing NEXT( ) button,
it moves to the next chapter.
Press PLAY button to recover the normal play speed.
During quick play, sound will be mute.(DVD/VCD)
1
1
Changing Disc Audio/Subtitle language during the Playback
Depending on the disc type, the Disc Audio/Subtitle function may not operate.
This function is available only during the playback.
For the disc containing the disc audio information, press LANGUAGE to select a variety of
languages such as Kor, Eng, etc.(DVD)
Changing Disc Audio
Press [DISPLAY] button.
1
Press ❷ buttons to select the Disc
Audio and
➛➛
❿❿
buttons to select the
language.
2
•
The subtitle language mark may vary with the disc type.
•
A disc can contain as many as 8 subtitle languages.
•
If you want the disc audio language whenever you play DVD, set a disc audio language in the
default setup.(See Page 19.)
For the disc containing the subtitle information, press S-TITLE button to select a variety of
languages such as Kor, Eng, Jap, etc.
Press S-TITLE button to turn it off and the subtitle won't appear any more.
Changing Subtitle Language
Press [DISPLAY] button.
1
Press ❷ buttons to select a subtitle language, and
➛➛
❿❿
buttons to fix
the subtitle language.
2
•
The subtitle language mark may vary with the disc type.
•
A disc can contain as many as 32 subtitles.
•
If you want the same subtitle language whenever you play DVD, set a subtitle language in the
default setup.(See Page 24.)
•
The Disc Audio/Subtitle language selection function may be available depending on the disc
type.
•
It won't operate after paused.
•
It is available only during DVD play.
(DVD, VCD)
(DVD)
HY-DVD3-ENG 2005.9.30 11:40 AM Page 24
27
Use
26
Repeat Play
(DVD/VCD/CD)
Repeating Play of Chapter, Title & Track(Music)
Press MODE ( ) button during
the disc playback.
Whenever you press MODE button, the mode will
keep changing in the following sequence.
1
Repeating Certain Area
Press Repeat Area ( ) button at
the point that you want to repeat
playing.
1
DVD
Chapter ➝Title ➝Off
VCD
Track ➝All ➝Off
CD, MP3
Track ➝Random Play ➝All
Press the button at both the start point(marked 'A') and the
end point(marked 'B') of the area that you want to repeat
playing. Only the selected area will be played over and
over again.
Press the button once more to cancel this setup.
DVD
- Off : When not playing in repeat
- Title : When playing the current title in repeat
- Chapter : When playing the current chapter in repeat
VCD
- Off : When not playing in repeat
- Track : When playing the current track in repeat
- All : When playing the current disc in repeat
CD, MP3
- Track : When playing the current track in repeat
- Random Play : When playing in Random
- All : When playing the current disc in repeat
•
The function may not be available depending on the disc
type.
(DVD/VCD/CD)
Slow Play
Slow Play
Press SLOW ( ) button in PAUSE or PLAY.
1
When pressing SLOW button ( ),
it plays with x1/2, x1/4, x1/8, x1/16, and x1/32 in the forward direction.
When pressing SLOW button ( ),
it plays with x1/2, x1/4, x1/8, x1/16, and x1/32 in the reverse direction.
Dividing Screens
(DVD/VCD)
(DVD/VCD)
Press PAUSE
()
button after a disc was paused.
Whenever you press it, the screen will proceed one by one track.
Press PLAY( ) button to recover the normal play speed.
1
Press PLAY ( ) button to recover the normal play speed.
During slow play, the sound will be mute.
This function is not available while CD, MP3 or WMA plays.
•
The sound will be mute during this function is activated.
•
This function is not available while CD, MP3, or WMA plays.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 26
29
Use
28
Searching Screen or Music
Searching by Time
Press Search ( ) button.
1
Press or ❷ button to move to the
Time menu.
2
You may search a screen or a Music by Progress or Title/Chapter/Track.
If you want to search 1hr 5min 15sec, press
1, 0, 5, 1, and 5 followed by ENTER button.
Then the screen after the selected hour will be
played.
3
Searching by Title or Chapter
Press Search( ) button.
1
Press or ❷ button to move to the
Title/Chapter menu.
2
If you want to search Title 1, Chapter 3, press 1 and 3
followed by ENTER button.
You have only to input the chapter to move in the same title.
3
Zooming-In/Angling
Zooming-In
Press ZOOM ( )button in the
Play or Pause mode.
1
Press ,❷, ➛➛and ❿❿buttons to move the zoomed area.
2
The convex mark ( ) will be displayed presenting zoom ratios.
Whenever you press the button, the screen will be zoomed by
the following ratio.
400% ➝1600% ➝off
Press ANGLE button to select the screen at an angle.
In case the maximum number of screen is 1, the screen
angle won't change.
You may zoom the screen by 2 steps during play or pause.
When a disc contains an area shot at various angles, you may see the screen at those angles.
Changing the Camera Angle
(DVD)
(DVD/VCD)
Press ANGLE ( )button.
The mark ( ) will be displayed, present-
ing the maximum number of screen.
1
3
HY-DVD3-ENG 2005.9.30 11:40 AM Page 28
31
Use
30
Photo View by JPEG Disc
Photo View by JPEG Disc
Put a disc in.
Make the printed side of the disc face
upward.
1
1. Press ❷ button to select a photo.
2. Press NEXT/BACK button while a photo is viewed to
move to the next/previous photo.
3. Press
➛➛
❿❿
button to rotate the photo by 90˚> 180˚> 270˚> ORIGINAL step by step.
4. Press ZOOM button to see the screen at the zoom ratio of 400% ➝1600% ➝Normal step
by step.
•
Only the files with the extension of JPG/JPEG are to be viewed.
•
The JPG file name shall not contain special marks (\,/,:,*,!,<,>,|,...)
•
Select the middle ( ) from the list to adjust the view speed in the order of (
➝ ➝ ➝
)
Playing MP3 and WMADisc.
Playing File
Put in a Disc.
Make the printed side of the disc face upward.
As it enters, the first song is automatically played.
1
Press STOP button to stop play.
Press PAUSE button to pause play.
Press PLAY button to replay.
If you want to play a music.
1. Press ❷ button to select a music(track) followed by ENTER button. A music will be
played.
2. Input number keys and use ENTER button to play the music of a number rightly.
❉
About MP3, WMA File
•
MP3 or WMA files shall be in the format of ISO 9660 or JOLIET.
•
The file name of MP3 or WMA shall not contain special marks( \,/,:,*,!,",<,>,|... )
•
You are not allowed to record unwritable MP3 or WMA files.
•
MP3 and WMA discs may not be played depending on the recording condition.
•
WMA files may not play the data less than 48Kbps, 33kHz..
•
Up to 6 tracks will be appeared per display.
•
Press( ) or ( ) button to listen to the next or previous music.
•
Press SLOW ( ) button to select a music in the other folder.
If you want to listen to only the music that you want to;
1. Press ❷ button to move to a music and press ❿❿button until it appears. Then, press
(ENTER) button to register the music in the program list.
2. Press
➛➛
❿❿
button to move to the program, and press ENTER button.
•
: When registering the whole list in the program
•
: When deleting the music from the program
•
: When deleting all the music from the program
HY-DVD3-ENG 2005.9.30 11:40 AM Page 30
33
Others
32
No sound
•
Aren't you operating in the SLOW or SEPARATE
mode? (There will be no sound in the Flexible
Speed Screen Play mode.)
•
Check the connection and further if SETUP is correct.
•
Is the disc inserted right?(Make the printed side of
the disc face upward.)
•
Check the disc condition.(Keep it clean.)
•
By the specification, some discs may not obey the
default condition. Only the disc that has the same
function with the SETUP menu will operate.
•
DVD discs are manufactured in the 16:9 Wide, 4:3
Movie, and 4:3 Zoom screen according to the manufacturing condition. Each type always its own rated
screen.
•
Check the DVD disc case to select the function
proper for a motion. For your reference, the 4:3
standard disc may not be seen wide.
•
Dolby Digital 5.1CH 3D sound effect can be heard
by the combination of the Dolby Digital exclusive
lamp. In addition, only the DVD disc recorded by
'Dolby Digital 5.1CH' may operate.
•
Only the disc audio/subtitle language recorded in a
DVD disc can be played.
•
Screen Angle is available only when the content by
angles is recorded in a DVD disc. In such a case,
the angle mark shall be printed in the product or
VFD.
The product does not operate
as per the initial setup condition.
TV Aspect selection is impossible.
Dolby Digital 5.1CH 3D sound
effect does not come out.
Disc Audio or Subtitle language which was selected
does not operate.
During DVD play, the Screen
Angle doesn't operate.
Troubleshooting
Take the following measures at first and further turn the product off and call our
Service Center.
The disc is running but the screen
does not appear or it is poor or
shaking.
•
Check if TV is turned on.
•
Check the connection.
•
Check if the main body is paused.
•
Check if the disc contains foreign materials or is
damaged.
•
Check the original condition of the disc.
•
Check the connection with the Dolby Digital Lamp.
•
Check the connection plug.
•
Check if the connection port is stained with foreign
materials.
•
Check the angle and distance of the remote control. Check any obstacle.
•
Check if batteries are sufficiently charged.
•
Isn't the product installed in too cold or hot place?
The optimum temperature for the operation ranges
0°C~ 50°C
•
Check the existence of a disc.
•
Check the power voltage.
•
Check if the right side of a disc was faced upward.
•
Check if the disc area code.
•
Check the disc condition.
The sound quality is not even.
The remote control does not operate.
There is no image or sound or the
disc come out in 2~5 seconds.
Nothing plays.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 32
35
Others
34
REFERENCE
KEC MOBILE APPLICATIONS TRI-MODE REMOTE CONTROLLER # RC9799 (or # RR9799)
The Tri-Mode Remote Controller is packaged with most KEC LCD Systems. In addition to
full remote
control of the LCD System, it also provides basic remote control commands for our DVD
and Videocassette
Players.
To control the DVD-3 with the RC9799 (or # RR9799), press the DVD MODE button.
To change to VCP control, press the VCP MODE button.
Notes:
•
The LCD System control buttons are always available. They are not affected by the DVD/VCP
MODE buttons.
• This unit is not a universal remote controller. It is only designed to transmit control codes to KEC
Mobile Applications products.
DVD Mode Video Output Method
NTSC/PAL
TV Mode Broadcasting Method
Voice Response 20Hz ~ 20KHz
Voice S/N Ratio 90dB
0.5Vp-p Impedance : 75
Ω
Output 0.5Vp-p Impedance : 75
Ω
1.0Vp-p Impedance : 75
Ω
Power DC 12V~24V, 1.5A
Power Consumption 18W
Product Size 178(D)x175(W)x50(H)
Weight 1.3Kg
Allowable Operating Temperature 0°C ~ 50°C
Allowable Operating Humidity 0% ~ 80%
Allowable Operating Condition Horizontal
Product Specification
Audio Analog
Audio Digital
Video
❉ Design, accessories, and product specification may be changed without notice.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 34
36
REFERENCE
ANOTE TO INSTALLERS CONCERNING THE KEC R-LINK SYSTEM
Most KEC Mobile Applications video products (TV, LCD, VCP & DVD) employ our R-LINK
System. This
allows all of our components to be remote controlled even if some of the components are
hidden from view.
If you are installing the DVD-3 along with one of our TV’s or monitors and one of
our VCP’s:
1. Connect an R-Link cable from the KEC TV/Monitor to the DVD-3’s R-Link Input
2. Connect an R-Link cable from the DVD-3’s R-Link Output to the R-Link jack on the
rear panel of the KEC VCP.
All KEC components may now be remote controlled by pointing any of the KEC
remote controllers at the remote sensor on any of the KEC components.
Please note that since pairs of KEC Mobile Applications Headrest Monitors are designed to be operated independently of each other, they are not equipped with R-Links. Please refer to the installation
information accompanying our Headrest Monitor Systems for information on the use of R-Link in conjunction with those systems.
HY-DVD3-ENG 2005.9.30 11:40 AM Page 36
Loading...