KEB 00.F4.010-3009 Instruction Manual

7/2003

PM.F4.01B-K102

KEB Memory Operator Memory Operator

BETRIEBSANLEITUNG

INSTRUCTION MANUAL

D 2

GB 3

1. General................................................................................GB 4

1.1 Product Description ............................................................. GB 4

2. Memory Operator ............................................................... GB 5

2.1 Operation as Digital Operator .............................................. GB 5

2.2 Operation as Memory Operator............................................ GB 6

2.2.1 Upload ......................................................................................................GB 7

2.2.2 Download ..................................................................................................GB 7

2.2.3 Abort and Fault Acknowledgement ........................................................... GB 7

3. Special Functions ..............................................................GB 8

3.1 Interlock of the Mode FU_OP............................................... GB 8

3.2 Changing of the Baud Rate.................................................. GB 8

3.3 Drive Mode in the Memory-Operator .................................... GB 9

3.4 Software Date ...................................................................... GB 9

4. Error Messages................................................................GB 10

Table of Contents

GB 4

00.F4.010-3009

1. General

This manual as well as the hardware and software are developments of
the Karl E. Brinkmann GmbH. Errors and omissions excepted! The Karl
E. Brinkmann GmbH prepared the documentation, software and
hardware to the best of its knowledge, but no guarantee is given that the
specifications will bring the user the efficiency aimed at. The Karl E. Brink­mann GmbH reserves the right to change the specifications without
obligation. All rights reserved!

KEB Antriebstechnik develops, manufactures and distributes static
frequency inverters worldwide in the industrial power range. Within the
scope of automization, systems are needed which are more powerful
and flexible . With this in mind KEB de v eloped a programming unit which
makes it possible to program several inverters quickly and without
internetworking. Parameter lists can be permanently stored in the
programming unit, so they can be immediately retrieved when needed.

1.1 Product
Description

The Memory Operator

- Can upload saved parameter lists from F4/S4 units

- Can download saved parameter lists

- Is downward compatible to the Digital-Operator (Exception: Drive-Mode)

- Can be directly connected to the F4/S4 units

Memory Operator

GB 5

Operation as

Digital Operator

see section 2.1

Operation as

Memory Operator

see section 2.2

2. Memory
Operator

The Digital Operator is the Standard Operator without interface in the
KEB COMBIVERT F4/S4. The Memory Operator is do wnward compatible
and can be used for normal operation except for one restriction.

During the operation of the Memory Operator the Drive Mode
in COMBIVERT F4/S4 may not be activated, because the key
assignment overlaps with the memory mode.

2.1 Operation as
Digital Operator

wait until the display or LED is off

Insert Operator and switch on the unit

Switch off COMBIVERT

According to the baud
rate of the Operator the
display is shown for 5
Seconds.

with 9600 Baud with 19200 Baud

or

! also see 3.2 Changing of the Baudrate!

When the display switches the unit is ready for operation

Operation as Digital Operator

GB 6

In this operating mode the parameter lists can

- be read from the inverter (Mode: FU_OP) (Upload)

- be written to the inverter (Mode: OP_FU) (Download)

Hold for approx. 5 sec. ➥ changes operating mode

Operation as Memory Operator

Switch off COMBIVERT

wait until the display or LED is off

Wait until display switches

with 9600 Baud with 19200 Baud

or

! also see 3.2 Changing of the Baud Rate!

Insert Operator and switch on the unit

Error Message Meaning

Display with locked Mode FU_OP.
The Mode FU_OP (Upload) can be locked, to make sure that
the data stored in the operator can not be overwritten.

see also section 3.1 Lock of the Mode FU_OP

Frequency inverter or servo controller was not recognized by
the operator. P ossible Cause:

- Connection pin broken/missing

- Baud rate of the inverter / Servo-controller not in accordance
with the baud rate of the operator

see 3.2 Change of the baud rate

To avoid problems for further operations, please pay attention to the
following error messages!

! Further error messages see section 4 error messages!

ENTER

F/R

FUNC.
SPEED

+

2.2 Operation as
Memory Operator

According to the baud rate
of the inverter the display
is shown 5 seconds

GB 7

FUNC.
SPEED

START

ENTER

F/R

ENTER

F/R

FUNC.
SPEED

START

ENTER

F/R

ENTER

F/R

FUNC.
SPEED

➡➡➡➡

➡

+

➡

➡➡➡

➡

+

Operating mode: download

Operating mode: upload

➥ Changes to the operating mode: upload

➥ Starts the upload process

Upload
operating

Upload completed

➥ Confirms the upload

Hold for approx. 5 sec. ➥ switches to normal operation

when Display „no_Lo“
see section 3.1
Lock Mode FU_OP

Operating mode: download

➥ Starts the download process

Download
operating

Download completed

➥ Confirms the Download

Hold for approx. 5 sec. ➥ switches to normal operation

2.2.3Abort and Fault
knowledgement

With the „Stop“-key a read- or write process can be interrupted. The error
message Err.1 is displayed. With the „Enter“-key the error message is
accepted and the operator changes into the selected operating mode.
Data, transfered before interruption are written in the selected target unit.
A parameter list, which is interrupted during the transfer to the operator
or COMBICARD displays at transmission (e.g.: mode OP-FU) the error
message Err .6, because the list does not include all parameters .

2.2.1 Upload

2.2.2 Download

GB 8

START

STOP

➥

➥

➥

START

STOP

➥

➥

➥

The mode FU_OP (Upload) can be locked, to make sure that the data
stored in the operator can not be overwritten.The status is displayed by
pressing the POWER-ON button and the „FUNC.-key“ simultaneously.

Lock Mode FU_OP:

Enable Mode FU_OP:

enable mode

FU_OP (Upload)

locked the
mode FU_OP

goes back into
normal operation

Locked mode

FU_OP (Upload)

goes back into
normal operation

release of
mode FU_OP

FUNC.
SPEED

➥

➥

FUNC.
SPEED

➥➥

Press

Switch on

Inverter

Press

Switch on

Inverter

START

➥

START

STOP

➥➥

➥

➥

START

➥

START

STOP

➥➥

➥

➥

T o adjust the baud rate of the operator to the baud rate at FU , the operator
can operate with 9600 baud or with 19200 baud. The actual adjusted
baud rate is displayed by pressing the POWER-ON button and the
„START-key“ simultaneously.

Increase Baud Rate:

Decrease Baud rate:

Press

Switch on

Inverter

9600 Baud

increase baud rate
to 19200 baud

goes back into
normal operation

Press

Switch on

Inverter

19200 Baud

goes back into
normal operation

decrease baud ra­te to 9600 baud

After changing of the baud rate the display of the operator goes into nor­mal operation.

3.2 Changing of the
Baud Rate

3. Special functions

3.1 Lock Mode FU_OP

GB 9

T o s witch an inverter/servo with Memory-Operator into the memory mode
do the following:

ENTER

F/R

+

FUNC.
SPEED

press

Memory Mode

Inverter/Servo in Drive-Mode

To return to the Drive-Mode, do the following:

ENTER

F/R

+

FUNC.
SPEED

press

Inverter/Servo is in the CP-Mode

Inverter/Servo in Drive-Mode

Enter the Drive-Mode password in CP.0

Drive-Mode

The Drive-Mode can not be exited when inverter type
45 (agree with F4-S V1.0) is used

If the STOP-key is pressed when the programmer is switched on, the
software date of the memory operator is shown.

Day Month Year

3.3 Drive-Mode in the
Memory-Operator

3.4 Software Date

GB 10

Memory capacity is not sufficient to
read in parameters.
(In mode FU-OP)

Unit is not suited for data transmission
with the memory operator.

Parameters have not been saved
completely in the operator memory
(RAM).

During download into memory and

errors message occurred (Err.1....5).

Thus, not all parameters could be
saved.

The connected inverter’s address
does not correspond to the inverter
address saved in the memory.

- Clear error message by pressing
the ‘ENTER’-key → inverter’s
address will not be changed

- By pressing the ‘START’-key → the
error is cleared and the addresses
in the memory operator are down­loaded.

Download to the inverter was stopped
(With Mode OP_FU)

The inverter was not in state „noP“
during writing parameter Fr.01 →
open control release and start
„download“ again.

Saved (e.g. type 45) and connected
(e.g. type 46) inverter do not
correspond.
All type numbers can be displayed
(In mode OP_FU)

- Clear message by pressing the
‘ENTER’ -key → download is
stopped.

- Clear message by pressing the
‘START’-key → download
continues. This function is used e.g.
to change inverter-software­versions, to transfer old download
lists onto the new software.

(Beispiel)

4. Error Messages

Display Description Cause / Remedy

Frequency inv erter or servo controller
was not recognized by the operator

Connection pin broken/missing; Baud
rate not correct adjusted; Operator or
controller defective

Upload unpossible - Data of the
inverter cannot be load in the
operator

Mode FU_OP (UPLOAD) is locked.
(see 3.1)

Selected operation canceled by user . “STOP” -key was pressed while

display was flashing

During an active operation (e.g. download)
the connected inverter or servo is no
longer recognized by the operator.

Connection pin broken or missing,
transmission interrupted, frequency
inverter/servo controller is switched
off.

© KEB xx.F4.xxx-xxxx 7/2003

Karl E. Brinkmann GmbH

Försterweg 36 - 38 • D - 32683 Barntrup

Telefon 00 49 / 52 63 / 4 01 - 0 • Fax 00 49 / 52 63 / 4 01 - 1 16

Internet: www .keb .de • E-mail: inf o@keb .de

KEB Antriebstechnik GmbH & Co. KG

Wildbacher Str. 5 • D - 08289 Schneeberg

Telefon 0049 / 37 72 / 67 - 0 • Telefax 0049 / 37 72 /67 - 2 81

E-mail: [e-mail]

KEB Antriebstechnik Austria GmbH

Ritzstraße 8 • A - 4614 Marchtrenk

Tel.: 0043 / 7243 / 53586 - 0 • FAX: 0043 / 7243 / 53586 - 21

Kostelni 32/1226 • CZ - 370 04 Ceské Budejovice

Tel.: 00420 / 38 / 731 92 23 • FAX: 00420 / 38 / 733 06 97

E-mail: [e-mail]

KEB Antriebstechnik

Herenveld 2 • B - 9500 Geraadsbergen

Tel.: 0032 / 5443 / 7860 • FAX: 0032 / 5443 / 7898

E-mail: [e-mail]

KEB China

Xianxia Road 299 • CHN - 200051 Shanghai

Tel.: 0086 / 21 / 62350922 • FAX: 0086 / 21 / 62350015

Internet: www.keb-cn.com • E-mail: [e-mail]

Société Française KEB

Z.I. de la Croix St. Nicolas • 14, rue Gustave Eiffel

F - 94510 LA QUEUE EN BRIE

Tél.: 0033 / 1 / 49620101 • FAX: 0033 / 1 / 45767495

E-mail: [e-mail]

KEB (UK) Ltd.

6 Chieftain Buisiness Park, Morris Close

Park Farm, Wellingborough, GB - Northants, NN8 6 XF

Tel.: 0044 / 1933 / 402220 • FAX: 0044 / 1933 / 400724

Internet: www.keb-uk.co.uk • E-mail: [e-mail]

KEB Italia S.r.l.

Via Newton, 2 • I - 20019 Settimo Milanese (Milano)

Tel.: 0039 / 02 / 33500782 • FAX: 0039 / 02 / 33500790

Internet: www.keb.it • E-mail: [e-mail]

KEB - YAMAKYU Ltd.

15 – 16, 2 – Chome, Takanawa Minato-ku

J – Tokyo 108 -0074

Tel.: 0081 / 33 / 445-8515 • FAX: 0081 / 33 / 445-8215

E-mail: [e-mail]

KEB Portugal

Lugar de Salgueiros – Pavilhao A, Mouquim

P - 4760 V. N. de Famalicao

Tel.: 00351 / 252 / 371 318 • FAX: 00351 / 252 / 371 320

E-mail: [e-mail]

KEB Taiwan Ltd.

1F, No.19-5, Shi Chou Rd., Tounan Town

R.O.C. - Yin-Lin Hsian / Taiwan

Tel.: 00886 / 5 / 5964242 • FAX: 00886 / 5 / 5964240

E-mail: [e-mail]

KEB Sverige

Box 265, Bergavägen 19

S-430 93 Hälsö

Tel.: [phone] • Fax: [phone]

E-mail: [e-mail]

KEBCO Inc.

1335 Mendota Heights Road

USA - Mendota Heights, MN 55120
Tel.: 001 / 651 / 4546162 • FAX: 001 / 651 / 4546198
Internet: www.kebco.com • E-mail: [e-mail]