KDF Zircom Instruction Manual

Instruction Manual

Thank you for purchasing KDF’s Sintering Furnace, Zircom.
Before using the unit, please read the manual thoroughly and
understand the capabilities and proper usage for this machine.
Please keep this manual in an easily accessible location for
future reference.

Contents

Safety Precautions ························· 1
Standard Accessories ····················· 4
Descriptions of Component Parts ······ 5
Preparations before use ·················· 7
Operation ····································· 8
How to use ··································· 9
Periodic Maintenance ····················· 16
Error Messages ····························· 17
Specification ································· 18

W1016100-A

-1-

Safety Precautions

About labels which are put on the unit.

This mark means that do not fail to read the instruction manual before use of the unit.

This mark means a warning that "Be careful not to jam something when the firing table
moves up and down".

This mark means a warning that "Hot parts. Be careful not to burn".

We recommend you to follow these instructions for proper use of the unit.

Directions

The safety precautions contained herein and the accompanying icons provided for the safe
use of this machine and to prevent injuries and loss on material resources.
Please read them carefully prior to your actual machine operation.

Failure to follow or ignorance of the directions may
cause severe injury or death.

Failure to follow or ignorance of the directions may
cause injuries or damages to material properties.

This mark means prohibited actions as shown inside or around it.
The illustration on the left means “Do not disassemble”.

●This mark means forced action and directions to follow as shown inside or

around it. The illustration on the left means “Unplug out of power outlet”.

This mark requires a user to pay attention to the caution mark as shown
inside or around it. The illustration on the left means “Be careful not to
jam your fingers “

-2-

●In the event when there is smoke, abnormal odors or sounds, turn off the power, unplug

immediately and contact the dealer for repairs.

●In the event when water enters the machine, turn off the power, unplug immediately and contact

the dealer for advice. Continued use may cause electric shock or fire.

●In the event when debris enters the machine, turn off the power, unplug immediately and contact

the dealer for advice. Continued use may cause electric shock or fire.

●Do not remove the panels or parts uninstructed or modify them in any manner.

This may cause electric shock or fire.

●In the event, when the machine is dropped or the furnace frame is dented, unplug

immediately and contact the dealer for advice.

Continued use may cause electric shock or fire.

●Please do not block ventilation holes and fan intake that are located on top surface and on

the side of the instrument. Doing so may cause internal temperature increase and cause fire

or malfunction of the unit.

●Plug to the outlet of the designated voltage described in the main specifications.

Use of other voltage may cause fire or shock.

●Keep the unit away from other equipment and walls. Leave minimum of 20cm of space around

the unit. Do not place anything on the top of the unit to prevent temperature increase

inside the unit. Continued use may cause fire or malfunction.

●When the unit is used, the quick firing stand provided must be set on the firing table.

Continued use without the quick firing stand may cause burn or fire.

●Do not place heavy items or place machine on the power cord and make sure that the cord is

not damaged. This may cause fire or electric shock.

●Please do not damage the power cord, or process, excessive bending, twisting, pull.

Doing so could damage the cord and cause fire or electric shock.

●When the cooling fan is in operation, do not unplug the power cord. The cooling fan will stop

and the outer case will get hot. This may cause fire.

-3-

●Unplug the main power cord from the power outlet when the machine is not in use for a long

period of time.

●In case of a periodic machine maintenance, unplug the power cord from the power outlet.

●Do not handle the plug with wet hands.

●When you unplug the power cord from the power outlet, do not pull the cord. If the cord is

damaged, it may cause fire or shock. Always remove by handling the plug.

●This machine is for dental sintering furnace. We do not recommend you to use the machine

for any other purpose.

●The improper installation or use may impair the safety protection function.

●Do not move up/down the table than necessary. The parts may be heated and fire or breakdown

may occur.

●Do not use the accessories and consumables we do no recommend. Breakdown or fire may

occur.

●Use the heat-resistant glove and tongs to take the firing tray in and out because inside of furnace

may be high temperature.

●Do not touch around the furnace (firing table) during heating up because of high temperature.

If any operations is required during heating up, use the heat-resistant glove.

●Do not place anything or put a hand under the firing table while the table is moving down.

Injury or breakdown may occur.

●When you move this machine, power off the switch, and unplug the main power cord from the

power outlet. This may cause fire.

●In case of using of coloring liquid, sinter firing objects after they are dried completely with other

burnout furnace. The insufficient dry may contaminate inside the unit and occurs the malfunction

of the unit.

-4-

Standard Accessories

When you open the box, we recommend you to make sure that the following
standard accessories are included. In addition, please check the unit for any damage
or dent. Contact our technical support team if there is any damage.

※Cracked insulator inside the muffle chamber is normal. This is not defected.

Quick Firing Stand 1pc Firing Tray S 3pcs Quick Firing Tray 1pc

Quick Firing Tray Stand 1pc Firing Cover 1pc Quick Firing Cover 1pc

Firing Beads Instruction Manual 1 booklet

We recommend you to save the carton and all packing materials for future use.

-5-

Descriptions of Component Parts

●Front View

Quick Firing Tray Stand

Quick Firing Stand

Firing Table

Operation Key

LCD Panel

Power Switch

SD Card Slot

Quick Firing Tray Stand ：Place to put firing tray and firing object.

Quick Firing Stand ：Place to put quick firing tray stand.
Firing Table ：Table to place quick firing stand and it moves up and down.
Power Switch ：Power switch for the unit.
LCD Panel ：LCD panel allows you to check programs/settings and operate the unit.
Operation Key ：F1～F4, Up/Down/Left/Right, Start/Stop and Table Up/Down are used to

Operate the unit.

SD Card Slot ：The slot allows you place SD card to backup and/or download firing data.