KBC WES-2500, WES-2-4, WAP, WAPOM, WSU Operation Manual

Headquarters

KBC Networks, Ltd.

25691 Atlantic Ocean Drive,

Suite B3

Lake Forest, CA 92630

U.S.A.

Main: 1-949-297-4930

Fax: [phone]

KBC Networks Ltd., EMEA

Carlton Suite, Barham Court

Teston, Maidstone

Kent ME18 5BZ

United Kingdom

Office: [phone]

Fax: [phone]

Email: [e-mail]

Web: www.kbcnetworks.com

Wireless Ethernet Point-to-Point & Multipoint Systems

Operations Manual

Version 20111027

Wireless Ethernet PtP & MP System Operations Manual

PREFACE

KBC WES PART NUMBERS

This operations manual covers the following part numbers:

DESCRIPTION KBC PART NUMBER
Point-to-point, 7.8 dBi gain directional SP Host and Client outdoor kit: WES-2500
Point-to-point, 16.7 dBi high gain directional SP Host and Client outdoor kit: WES-2-4
Point-to-Multipoint, 7.8 dBi directional Host Access Poi nt outdoor kit: WAP
Point-to-Multipoint, 2.5 dBi Omni-directional Host Ac cess Point kit¹: WAPOM
Point-to-Multipoint, 7.8 dBi gain directional Subscriber Unit outdoor kit: WSU
Point-to-Multipoint, 16.7 dBi gain directional Subscriber Uni t outdoor kit: WSUP
Point-to-Multipoint, 24 dBi Parabolic Dish Subscriber Unit o utdoor kit: WSUDI
Point-to-Multipoint, 2.5 dBi Omni-directional Subscriber Unit kit¹: WSUOM
Replacement Single-point Host, 7.8 dBi gain directiona l unit (module only): WEM
Replacement Single-point Host, 16.7 dBi gain 6” x 6” patch (module only): WEMP

¹Not weatherproof, must be enclosed in an SWE -O housing if used outdoors

Accessories:

24 dBi parabolic dish antenna (add to WSU or WEM part number only) ²: 18D
Outdoor enclosure used with WAPOM or WSUOM: SWE-O
Outdoor enclosure used with WAP, WSU or WEM part numbers: SWE
Pole/wall mounting kit for standard 2” pole, with swivel mount for alignment³: LNBMB
Mid-span compliant power injector module⁴ PIM
500 mA 12 VDC non-regulated power supply⁴ PS-500-A

²One included in WSUDI kit
³One per WES module included in all directional WES series kits
⁴ One per WES module included in all WES series kits

PRODUCTS INCLUDED IN KITS

All Point-to-point WES kits include the following:
Qty 2: WES Modules (WES-2500) or WES patch units (WES-2-4)
Qty 2: PIM
Qty 2: PS-500-A
Qty 2: LNBMB
Qty 2: Strain Relief for Ethernet cable connection at RJ-45 LAN port of WES module
Qty 1: Operations manual

All Multipoint WES kits include the following:
Qty 1: MP Host module (WAP, WAPOM) or subscriber unit (WSU, WSUP, WSUDI, WSUOM)
Qty 1: PIM
Qty 1: PS-500-A
Qty 1: LNBMB (excluded in WAPOM or WSUOM)
Qty 1: Strain Relief for Ethernet cable connection at RJ-45 LAN port of WES module

Qty 1: Operations manual

P-1

Wireless Ethernet PtP & MP System Operations Manual

PREFACE (CONTINUED)

TECHNICAL SUPPORT AVAILA BILITY

This manu al is comprehensive to the extent that it will answer many of your technical
questions. Our toll free technical assistance is available should you require additional
assistance. KBC offers technical support over the phone or by way of e -mail to all KBC
integrators, dealers and end users of the WES products. Our technical support hotline is
available during regular US west coast business hours, Monday through Friday on all
non-major holiday business days. KBC will follow up on all electronic inquiries before
the end of the following business day.

NORTH AMERICA
888-366-4276: Monday – Friday 10am-8pm Eastern (7a m-5pm Pacific)

[e-mail]: 24hr availability, response time varies

HAWAII & ALASKA / GUAM, PR & OTHER US TERRITORIES
949-297-4930: Monday – Friday 7am-5pm Pacific Time

[e-mail]: 24hr availability, response time varies

Note: the toll free 888# does not work from Alaska

CENTRAL / SOUTH AMERICA

[e-mail]: 24hr availability, response time varies

ASIA

[e-mail]: 24hr availability, response time varies

SOUTH PACIFIC / PACIFIC ISLANDS

[e-mail]: 24hr availability, response time varies

EUROPE
[phone]: Monday – Friday 9am-5pm UK T ime

[e-mail]: 24hr availability, response time varies

Note: this product is not CE approved for use in Europe

AFRICA

[e-mail]: 24hr availability, response time varies

Technical Support is offered in English, however, KBC has worldwide representatives
who can provide technical support in many local languages.

Please note: technical assistance is available after having read through this manual.
Comprehension of terms and topics will assist in trouble -shoot procedures.

P-2

Wireless Ethernet PtP & MP System Operations Manual

INDEX

PREFACE P1-P2

KBC WES Part Numbers & Included Products in WES Kits P1
KBC Technical Support Availability P2

INDEX i

GOVERNMENTAL & SAFETY INSTRUCTION ii-v

Important Safety Instruction ii
FCC Required Information and Radio Frequency Statement iii
FCC and IC Restrictions iv
Environmental Restrictions v

SET UP & SYSTEM OVERVIEW 1-9

WES Set Up 1
FCC Regulatory Alert 2
WES Details – Physical Description & Diagram: Directional WEM 3
WES Details – Physical Description & Diagram: Omni-directional WEM 4
Power Injector Details – Physical Description & Diagram 4
WES LED Patterns 5
WES Cable Connection Diagrams 6
WEM Installation & Operation 7-8
Locator Software Tool Orientation & Operation 9

ADVANCED OPERATION – INTERNAL WEB BROWSER GUI 10-19

Log In Reaching the GUI and determining the default GUI password 10
Status – Device Status learn the parameters of the wireless and Ethernet configurations 10-11
Status – Host/Client Association Lists Important signal strength information 12
Status – Statistics Information regarding Ethernet packet & WES traffic stats 13
Basic – Wireless Wireless and encryption method reconfiguration instructions 14-15
Basic – Ethernet Info in order to change static or DHCP subnet and gateway settings 16
Advanced – Admin Administrator password and device name reconfiguration instructions 17
Advanced – System Restoring to defaults using the internal GUI web browser pages 18
Advanced – Firmware Current firmware level & uploading firmware upgrade files 19

SPECS / APPROVALS / TROUBLE-SHOOTING / WARRANTY 20-24

WES Configuration Table 20
Node Specifications & FCC/IC Approvals 22-24
Trouble-shooting 25
Warranty Information 26

APPENDIX A1-A2

i

Wireless Ethernet PtP & MP System Operations Manual

IMPORTANT SAFETY INSTRUCTION

For your protection, please read and observe all safety instructions before operating
this system and keep this sheet and any additional instructions for future reference.

INSTALLATION & USE

OBSERVE WARNINGS: All warnings in the operating instructions should be carefully
followed. Do not make any modifications to the Wireless Ethernet Module (WEM),
Power Injection Module (PIM), or any other KBC electronic device, as the unit(s) will
no longer comply with FCC regulations and therefore void its warranty.

WATER AND MOISTURE: The WEM is weatherproof provided it is installed in
accordance to the mounting details listed on page 7. However, further protection or
housing is suggested for har sh environments, as moisture damage voids its
warranty. The PIMs used in this system are NOT weat herproof. None of the
modules in this system are waterproof and should never be submerged. Severe
electrical shock, personal injury or damage to the equipment may result.

POWER SOURCE: Connect the equipment to a power source only of the type
described on the operating instructions or as marked on the equipment. Excessive
or insufficient amperage or voltage can cause extended trouble-shooting or even

damage that could negate its warranty. The power supplies’ cable should not be

modified/extended due to the ability to use up to 100 meters of power over Ethernet
cable. In addition, Ethernet cable running from the PIM to the WEM should be kept
separated from high-voltage cables and/or transformers.

ATTACHMENTS: Use only KBC supplied or recommended Power Injection Modules,
Power Supplies, Cat5 Cables and weather seals and plugs.

WHEN NOT IN USE: Unplug the power if the equipment is left unattended or unused
for long periods of time or during lightning storms.

REPLACEMENT PARTS: When replacement parts are required, use only replacement
parts specified by KBC. Unauthorized substitutions may result in damage to the
system and could void the warranty.

ii

Wireless Ethernet PtP & MP System Operations Manual

FCC REQUIRED INFORMATION – RADIO FREQUENCY
INTERFERENCE STATEMENT FOR CLASS A DIGITAL DEVICES

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. Thes e limits are designed to
provide reasonable protection against harmful int erference when the equipment is
operated in a commercial environment. This equipment generates, uses, a nd can
radiate radio frequency energy and, if not in stalled and used in accordance w ith the
instruction manual, may cause harmful interference to radio frequencies. Operation
of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

This equipment is designed to be professionally installed exclusively for fixed point­to-point and/or multipoint applications. These products must be controlled due to
radio frequency power output levels emitted with special consideration given to
antenna placement as it relates to human exposure. Compliance is the re sponsibility
of the installer and user.

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the li mits for an
intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This
equipment generates, uses, and can radiate radio frequency energy. If not installed
and used in acco rdance with t he instructions, it may cause interference to radio
communications. The limits are designed to provide reasonable protection against
such interference in a residential situation. However, there is no guarantee that
interference will not occur in a particular installati on. If this equipment does cause
interference to radio or television reception, which can be determined by turning the
equipment on and off, the user is encou raged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna of the affected radio or television.
Increase the separation between the equipment and the affected receiver.
Connect the equipment and the affected receiver to power outlets on

separate circuits.

Consult the dealer or an ex perienced radio/TV technician for help.

Shielded cables must be used with this unit to ensure compliance with Class A FCC
limits. Changes or modificati ons to this unit not expressly approved by the party
responsible for compliance could void the users authority to operate the equipment.
Changes or modifications not expressly approved by KBC could void the users
authority to operate the equipment.

iii

Wireless Ethernet PtP & MP System Operations Manual

FCC POWER OUTPUT RESTRICTIONS

The FCC does not require licensing to implement this device. License -free operation in
the industrial, scientifi c, and medical band is documented in FCC Rules Part 15 .247. It
is the responsibili ty of the individuals designing and implementing the rad io system to
assure co mpliance with any pertinent FCC Rules and Regulations. This device must be
professionally installed.

EXPOSURE TO RADIO FREQUENCY FIELDS

The WES is designed to operate on the 5 GHz frequency band with up to 50 Watts EIRP
maximum transmit power. This level of RF energy is above the Maximum Permissible
Exposure (MPE) levels specified in FCC OET65:97-01. The following precautions must
be taken during installation of this equipment:

The installed antenna must not be located in a manner that allows exposure of

the general population to the direct beam path of the antenna at a distance
less than 20 centimeters. Installation on towers, masts, or rooftops not
accessible to the general population is recommended; or

Mount the antenna in a manner that prevents any personnel from entering the

area within 20 centimeters from the front of the antenna.

It is recommended that the installer place radio frequency hazard warnings

signs on the barrier that prevents access to the antenna.

During ins tallation and alignment of the antenna, do not stand in front of the

antenna assembly.

During installation and alignment of the antenna, do not handle or touch the

front of the antenna.
These simple precautions must be taken to prevent general population and installation
personnel from exposure to RF energy in excess of specified MPE levels.

INDUSTRY CANADA RESTRICTIONS

This device is in compliance with the applicable sections of the Industr y Canada RSS­210 Spectru m Management and Telecommunications Radio Standard Specification that
governs Low Power License-Exempt Radio commu nication Devices. Specifically, the
output EIRP of this device relative to antenna gain is factory set to ensure comp liance
with section 6.2.2(q1)(iv)(g).

In addition, it is noted for all users that high power radars are allocated as primary
users (meaning they have priority) of the 5250-5350 MHz and 5650-5850 MHz
frequency bands and these radars could cause inte rferenc e and/or damage to LELAN
devices such as are covered by this manual.

iv

Wireless Ethernet PtP & MP System Operations Manual

ENVIRONMENTAL RESTRICTIONS OF WIRELESS DEVICES

KBC products are engineered to the highest standards and designed to work
in a variety of wireless applications and environments. A wireless environment
includes the site in which the product is installed, the installation itself and
any extra materials that might be necessary to complete the wireless project.
Due to the fact that environments and installations differ from site to site,
KBC cannot control the variables required to ensure an ideal environment.
Therefore, it is not possible to guarantee a successful application based on a
drawing, application note, distance calculation, quote or other type of
material that KBC may provide. Should a quote, drawing, etc. be made
available, it is based on the performance of the WES product in an ideal
environment with clear line-of-sight, absence of 5 GHz interference and/or
frequency multi-path reflection. Therefore, KBC cannot be held responsible
should the products not operate as desired or should additional products be
required to complete a project. In addition, should a particular environment
restrict the usage of the WES in any way, KBC offers a thirty (30) day return
policy from date of original shipment (see page 2) to the original purchaser.

v

Wireless Ethernet PtP & MP System Operations Manual

WES SET UP PROCEDURES

KBC recommends that all equipment be bench tested before being installed
onsite.

WIRELESS ETHERNET MODULE SETUP

1. Remove the Host and Client from the box, select frequency via the

rotary switch at the side of the unit. (Factory set to channel 0 unless

otherwise noted) The channels of each set of Host/Clients must be

matched for the radios to communicate with each other. For multi-

connect devices, each Client must be set to the same channel as the

Host that it will be connected to. If connecting more than one Client

to a single Host, please see the advanced operation section of this

manual for multipoint setup.

2. Mount the Client at the remote location. Point the Client as accurately

as possible to the point where its Host AP will be mounted.

3. Remove the Power Injection Modules (PIMs) from the box and

determine where they will be located for each Host/Client. Total

distance between a Host/Client and connected Ethernet device cannot

exceed 100 meters (300 feet). The PIMs can be located anywhere

along the 100m of CAT5 cable. Connect a standard CAT5 straight

through patch cable to the “P + Data Out” port on each PIM to its

corresponding Host/Client. “Data In” port on each PIM should be

connected to its respective Ethernet device using a standard CAT5

straight through patch cable. A crossover cable may be needed

depending on the LAN port of the Ethernet device in use.

4. Connect the included power supplies to the “Power In” port on the

PIMs and plug the transformers into a standard 110VAC outlet. If the

Ethernet devices on each end are connected, powered up and aimed

correctly, the “Link Activity”, “Power” and “Signal Level” LEDs will

illuminate. If the Ethernet device is not connected the “Power” LED

and “Signal Level” LEDs only will illuminate. If the “Signal Level” LED

is flashing, reposition the modules to achieve max signal strength.

For multi-connect applications, each Client will show a solid green

light when connected to a Multipoint Host. A flashing green LED on

the Multipoint Host Access Point will indicate the number of Client

Subscriber Units to which it is connected.

1

Wireless Ethernet PtP & MP System Operations Manual

FCC REGULATORY ALERT

As of 20 July, 2007, a new FCC regulation has gone into effect which impacts
operators of the U-NII band in the United States. As a result of this regulatory
change, several KBC products are affected. The FCC regulation impacts the sale of
wireless equipment in the 5.25-5.35 GHz band. The regulation states that all
devices imported and marketed after the 20 July, 2007 deadline must support
radar detection as specified by FCC in the 5.25-5.35 GHz frequency band.

AFFECTED KBC PRODUCTS
To comply with FCC regulation, KBC has disabled the 5250-5350 MH z (5.25-5.35
GHz) frequency selections. The following products contain 5745-5825 MHz options
only:
Point to point: WES-2500; WES-2-4; WES-12*; WES-30*
Point to multipoint: WAP; WAPOM; WSU; WSUP; WSUOM; WES-D; WES-OD; WES­D1-2
*Discontinued

KBC RETURN POLICY

KBC wireless products come with a 2-year limited warranty, (see page 24 for warranty
information) unless other wise specified. In addition to the 2-year warranty, products
may be returned within thirty (30) days of shipment provided the products are in like
new condition a nd in the original pa ckaging. Contact your KBC dealer or distributor to
obtain an authorization to return the merchandise for credit.

Return authorizations for repair can be sent directly to KBC with a valid RA
number. RA’s are issued to KBC distributors, dealers or in tegrators with a valid
resale license. End-users should return products th rough their KBC dealer who can
contact KBC to obtain an RA number for repair.

Phone #: [phone]
E-mail: [e-mail]

2

Wireless Ethernet PtP & MP System Operations Manual

WIRELESS ETHERNET SYSTEM (WES) DETAILS

The WES is a plug and play CAT5/Ethernet cable replacement system. It operates in the
5GHz U-NII bands on 5 non -overlapping channels. The WES system enables a wide
variety of IP cameras, DVR/NVRs, managed/non-managed switches, encoders/decoders
and web servers to be used across long range wireless line -of-sight links.

A. FRONT VIEW

1. Module case

2. Antenna cover

B. REAR VIEW

1. Serial Number

2. List of Available Frequencies

3. Channel Selector

(on side of WEM)

Factory set to channel 0 unle ss

otherwise noted.

4. Status LEDs

Amber= Link Activity

Red= Power

Green= Signal Level

5. LAN Port

(underside of WEM)

3

Note: moun t Host/Client so that vertical Ethernet port is
at bottom and use weatherproof caps and plugs fo r
outdoor use as described on page 7

KBC NETWORKS, LTD.

LAKE FOREST, CA 92630

MODEL: WEM
FCC ID: JRRWES
IC: 4887A-WES

08500

This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) This Device may not cause
harmful interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operation.

POLARITY

LINK ACTIVITY

POWER

SIGNAL LEVEL

ETHERNET PORT

0 5745 mHz
1 5745 mHz
2 5745 mHz
3 5745 mHz
4 5765 mHz
5 5785 mHz
6 5805 mHz
7 5825 mHz

CHANNEL SELECT

1 2 3 5 4

1

2

The LAN port must be weather protec ted with supplied strain­relief positioned so the connector is at bottom of the case.
Weatherproof strain-relief plug should be tightened down to
the bottom of the case. The cable portion of the plug should be
open to allow moisture release and limited cable movement
but closed to restrict insects from entering the unit.

Technical Note:

FAQ: How Does the FCC Re gulation Affect the WES User?

If one WES System is in use and there are no plans to add to the wireless project
then it may not affect you at all. However, if you are using two or more system s
then you may need to change frequencies according to the available channels.
Multiple WES systems set to channels 0, 1 or 2 (all unavailable 5.2/5.3 GHz
frequencies) will all be defaulted to channel 3 (available 5745 MHz). The next
available frequency in sequence would be channel 4 (5765 MHz). Channels 3
through 7 are all individual frequencies but channels 0-2 are not available.

Wireless Ethernet PtP & MP System Operations Manual

WIRELESS ETHERNET SYSTEM DETAILS (CONTINUED)

OMNI-DIRECTIONAL WEM (WAPOM / WSUOM)

A. SIDE VIEW

1. Antenna Dome Cover

2. Channel Selector

(Underneath plastic cap)
Factory set to channel 0
unless otherwise noted

3. LAN Port

4. Mounting Holes

Rear view is identical to the directional WEM

The WAPOM and WSUOM are not weatherproof when mounted outdoors without an
additional SWE-O (or other NEMA rated enclosure) housing. See SWE -O mounting
instructions for proper installation of the WAPOM/WSUOM in the outdoor housing.

POWER INJECTION MODULE (P IM)

Note: The Power Injector Modules are not weatherproof units and must be protected from moisture.

PIM DESCRIPTION

A. FRONT VIEW

PoE NOTIFICATION

The WEMs are mid-span co mpliant and must be powered using the supplied
power injection module. If an 802.3af compliant PoE switch is used, connect to
a non-PoE port of the switch only.

4

Wireless Ethernet PtP & MP System Operations Manual

WES LED PATTERNS

For all units, the red power LED will either be active to show that it i s powered up or off
to indicate no power. The link LED (Link Activity), or the amber LED, will flash rapidly
when there is activity across the wireless connecti on. The green LED, or Signal Level,
will illuminate upon connection. There are a few different regular Signal Leve l LED
responses determined by the type of product in use:

POINT TO POINT HOST LE D ACTIVITY (WES-2500 & WES-2-4 Hosts)

If the green LED flashes at any rate it is indicating a less than max signal connection.

MULTIPOINT HOST LED ACTIVITY (WAP / WAPOM)

CLIENT LED ACTIVITY (All Clients from all part numbers excluding WAP/WAPOM)

The Client LED status will remai n the same regardless of the type of host to which it
is connected. The Signal Level LED should remain solid t o indicate a max signal
alignment. If the green LED flashes at any rate it is indicatin g a less than max signal
connection. A flashing green LED can be corrected by further alignment of the Client

to its Host.

5

1

3

1. DATA IN – Connect to Ethernet Device

2. POWER LED – Indicates power is on when lit

3. P+DATA OUT – Connect to the WEM

4. Power supply input (in rear of PIM)

2 3 4

1

Upon power
and cable
connection

Upon
connection to
Client

Upon
video
stream

LED activity if connected to 4 Clients

Upon power
and cable
connection

Upon connection to Client(s)
And video streaming or other
activity

Upon power
and cable
connection

Upon
connection
to Host

Upon
video
stream

FAQ: How can I tell the difference between an omni-directional and
directional WEM?

The difference in appearance between an omni-directional WEM (WAPOM and
WSUOM part numbers)and a standard directional WEM (WE S-2500, WES-2-4, WAP,
WSU, WSUP) is the antenna dome cover. The omni antenna has a small dipole
under the dome cover and is about a 0.25 (7mm) inch taller than the directional
antenna dome cover.

1 2 3

4

Wireless Ethernet PtP & MP System Operations Manual

WES CONNECTION DIAGRAMS

The following wiring schemes represent the configuratio ns that have been tested and
verified by KBC based on typical Ethernet wiring solution s. Other wiring configurat ions
could be possible based on the application. A bench test is recommended to verify the
designs below.

POINT TO POINT SYSTEM

IP Camera NVR

Client Host

MULTIPOINT SYSTEM

Client

MP Host

Client

* Type of Cat5 configuration may be determined by LAN port of the Ethernet device.

If the port is a 10/100 port, you may require a crossover ca ble. Most cables used

to the connect the WES system are configured using a straight-through color

code.

6

Wireless Ethernet PtP & MP System Operations Manual

WEM INSTALLATION & OPERATION

A. SELECT CHANNE L

1. Remove the ½ inch plastic cap on the side of the Host/Client .

2. The rotary switch inside features a small black arrow pointing at the

selected channel indicator. The switch has 8 positions. Channels 0
through 3 are all 5745 MHz. To select a different frequency, select
channel 4 or higher then power cycle the WEM device.

Default set to channel 0 (5745 MHz) as shown in the
diagram to the left.

3. Power cycle device to implement channel change

4. Reseal port by replacing weatherproof plug

B. MOUNT DIRECTIONAL HOST/CLIENT

Mount the Host/Client using the included wall/pole mount bracket and

hardware. Connect the black mounting assembly with adjustment swivel to

mounting L-shaped bracket with the ¼-20 button head screw. Connect the

unit to the mounting assembly using the ¼” mounting hole in the case

(diagram B-1). Position the Host and point it in the direction of the Client (or

Client to Ho st) and tighten the swivel mount. Lock in the antenna upon a solid

green Signal Level LED (Multipoint Host green LED will flash).

Diagram B-2, above right, show s strain relief weatherproof plug. RJ-45 port

protected when plug in use. Tighten snug to case bottom (section A) but

leave open enough (section B) for slight cable movement and condensation

release.

7

Ethernet
Cat5*

Straight­through

Straight-through

Ethernet
Cat5*

Ethernet
Cat5*

Straight­through

Straight­through

Ethernet
Cat5*

Ethernet
Cat5*

Straight-through

< 90⁰

FAQ: To which port on the PIM does the WES connect?

The “P+Data Out” always connects to the WEM.

FAQ: How far from the Ethernet device can I mount the
WEM?

The cable from the Ethernet device to the WEM cannot exceed
100 meters (326 feet). The PIM can be situated anywhere along
that 100m length of cable.

0

7

6

4

2

1

3

5

B-1

B-2
A

B

Wireless Ethernet PtP & MP System Operations Manual

WEM INSTALLATION & OPERATION (CONTINUED)

C. CONFIGURE CABLE

Determine the length of Cat5 cable that will be needed and where the PIM will
be located. The total length of cable from the WEM to the Ethernet device
cannot exceed 100 meters (325 feet), however, the PIM can be located
anywhere along the overall 100m of cable.

Slide the weatherproof connector over the cable jacket before crimping the
connector. See below for color-code standards to configure the correct type of
Ethernet cable.

Ethernet standard straight-th rough cable configurations used must be
configured to one of the Ethernet standards (568-A or 568-B) in order for the
WES system to operate efficiently. Any deviation from one of the two standard
configurations can lead to undesired activity.

Pin out for color codes 568-A and 568-B:

568-A 568-B
1- Green/White 1- Orange/White
2- Solid Green 2- Solid Orange
3- Orange/White 3- Green/White
4- Solid Blue 4- Solid Blue
5- Blue/White 5- Blue/White
6- Solid Orange 6- Solid Green
7- Brown/White 7- Brown/White
8- Solid Brown 8- Solid Brown

A cable configured with the 568-A color code on one end and the 568-B color
code on the other end is an Ethernet standard crossover cable.

Connect the RJ-45 connector into the WEM’s LAN port. Slide the strain relief
back up the cable to the threaded port in the case and screw it into the
Host/Client and tighten. Tighten the clamping nut until the CAT5 cable is
sealed in the connector. The weatherproof strain relief should be tight to the
case but the opening should remain loose enough to enable condensation
release.

D. CONNECT HOST AND CLIENT(s)

Verify antenna alignment and LED status. See page 5 for applicable LED
activity. Ensure the green power LED on the PIM is illuminat ed. The WEM red
power LED should be on provided the cable into the LAN port is seated in
properly. If multiple Clients connect to one multipoint Ho st, verify all Clients
are on the same frequency as the MP Host and pointed in its direction.

E. ESTABLISH LINK

Follow above steps, A through D, for all WEMs of the system to be established.

NOTE: In some cases, depending on th e physical and RF environ ment, a
useable throughput rate may not be possible. Contact KBC for more
information – 888-366-4276 or [e-mail].

8

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION

WEB BROWSER INTERFACE

Each Host and Client has a web brow ser interface to access the advanced setup
functions. If changing advanced settings, be sure to conn ect and power the radios
individually. To access this interface, connect the WES to the Ethernet port on a
computer, launch the web browser and type in the default IP address at

http://192.168.1.200 for the Host and http://192.168.1. 201 for the Client. The

configuration of the computer used to access the WEM may need to be changed
depending on its IP settings. The IP address of the computer should be set to

192.168.1.xxx. The xxx setting can be any address 2 – 254 excluding 200/201 or
any other IP address(s) you wish t o use for a WEM on that subnet (or
Encoder/Decoder/WES Mesh/Thru Link product if applicable). The Subnet mask
should be 255.255.255.0. If you have any questions or concerns about changing
these settings, please contact your network administrator.

LOCATOR SOFTWARE TOOL – AVAILABLE FOR DOWN LOAD ONLINE
Available on our web site at ww w.kbcnetworks.com/softwa redownloads.htm is a too l
that can search for the WES unit IP address. The tool can l ocate the W EM regardless
of the subnet setting of the computer on which it is running.

Connect to the Host and click “S can”. Upon wireless connection t o the Client, the
remote unit will appear after the clicking “Scan” again.

Click “Web” or double-click any of the WES devices to access the internal GUI

interface.

9

FAQ: What does the yellow

icon next to the “WES Client”
or “WES SP/MPHost ” device

indication mean?

An <<!!>> icon next to the device
indicates an Ethernet issue. If

your computer’ s static IP address

is set to a different subnet than
the WEM, the icon will appear.
Duplicate IPs, network loops, low
signal strength and several o ther
reasons are other possibilities.

FAQ: What is the “AutoIP”?

If the yellow <<!!>> icon appears,

the “AutoIP” button will be

available. Click t he icon to hi-

light in blue. Then click “AutoIP”.

This function will change the IP of
the WEM to match the subnet of
the connected computer. After
approximately 10 seconds, click

“Scan” and the new IP address

should appear without the icon.

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

WEB BROWSER LOG IN

The default password for each WEM is admin (all lower case).

WARNING: IF YOU CHANGE THE USER NAME AND/OR PAS SWORD, Y OU WILL NEED
TO KEEP A RECOR D OF YOUR CHANGES IN A SAFE PLACE. IF THE PASSWORD IS
FORGOTTEN OR MISPLACED, THE UNIT MUST BE RETURNE D TO KBC TO BE RESET.

INTERFACE CONFIGURATOR WEB PAGES

A. STATUS – DEV ICE STATUS

1. Point-to-Point Host AP

The device status page provides the details of the Single-point Host

configurations. The Access Point Name can be changed on the “Admin”

page of the ADVANCED tab. The SSID cannot be changed. The updated
firmware is as shown: 7.06.

2. Multi-Connect Host AP

The device status page provides the details for the Multipoint Host
configurations.

See screen shot and description on page 11 for information on the device status page.

10

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

GENERAL

Firmware Version: 7.06 for units with 0-7 rotary channel sele ctor; 7.05 for 0-9

ETHERNET

Mac Address: Every Ethernet device has its own unique Media Access

Control (MAC) identifier. This indication is in reference to the
internal motherboard. See WIRELESS for radio MAC Address.

IP Address: Verify all Host/Client WEMs are on the same subnet but do

not conflict.________________ _______________________

Subnet Mask: The filter used for association of Ethernet devices.____ _____

WIRELESS

MAC Address: The MAC address of the radio. Record this information for

tracking purpose.__________ _____________________ ___
Current Trans Rate The Client will display its signa l rate to the Host. Max is 54. _
Current Frequency Client- Current frequency scanned for AP_______________ _
Turbo Mode Available on 5765 & 5805 MHz only. 0= OFF, 1 or 2= ON___
Rotary Switch Pos Correct indicator for current channel. Refer to label for

frequency____________________________________ ____
Jumper Settings 25.5 ON= 5745-5825 MHz only; OFF= all 5 GHz available

17.7 ON= All 5 GHz frequencies available on WSUP Client or

WEMP Host 6 inch patch antennas . Usually set to OFF. _____
Security Type Displays current encryption me thod. WPA, WPA -2 and WEP

available. WPA-2 is default and preferred encryption method.

11

Default password: admin

NOTE:
KBC and MicroTek Electronics merged in 2008. The following
screen shots show the ex isting MicroTek interface as present in
the WES series.

FAQ: My Client is set to 5745 (or other) MHz but the interface
shows a different frequency. Is it configured inco rrectly?

The Client cycles through all of the various frequencies (though it is
still using the frequency selected) in order to associate with the
appropriate Host AP based on actual frequency, signal rate and RSSI
(see page 12). This is normal, the Client is actually on the frequency

it was programmed to use. Refer to “Rotary Switch Position” and

match that channel to the frequency list shown on page 3.

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

B. STATUS – HOST/CLIENT ASSOCIATION LISTS

1. Single Point and Multipoint Host AP

The “Client List” page of the Host AP (either a Single Point or Multipoint Host)

shows the MAC Address(es) of the paired or gro uped Client Subscriber Units (SU)
connected to the Ho st AP. For point -to-point systems, one MAC will be shown. A
single point Host should not list more than one Client MAC address. However, a
Client may be able to see more than one Host AP. A multipoint Host AP will show
all of the Client SU MAC addresses currently associated. The page will show the
mode, rate and RSSI communication information for each connected Client SU.

2. Client

The same information is shown on the Client’s “Host AP List”. Other hosts

may appear as the Client searches all available APs on the frequency
band.

12

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

C. STATUS – STATISTICS

The Statistics page is the equivalent of a constant ping without the response time
data. It will indicate the number of transmitted and received data packets versus
the number of dropped or collided packets. As the system continues to run, these
numbers will accumulate until cleared to 0. Refresh to see updated statistics.

ETHERNET STATISTICS
Packet information at the motherboard and cable level. If packets are dropped or
collided at the Ethernet level then there could be a problem with the cabling or
other LAN related hardware.

WIRELESS STATISTICS
Packet information across the wireless link. If packets are dropped at the wireless
level then a new frequency might be suggested. A clearer line of sight or antenna
alignment may be necessary as well.

13

FAQ: What is the Rate ind ication?

The signaling rate is the speed in megabits per second (Mbps) at which the two
radios are communicating. A max signal rate is 54. If the co nnection cannot be made
at a max rate, the radios slow down the connection in order to attempt to connect at
a lower rate, such as 48, 42, 36, etc. This rate is a “snaps hot” of the speed in Mbps
for the last packet of information as it crossed the wireless li nk. This is not to be used
as an indication of overall throughput for the wireless conne ction.

FAQ: What is the RSSI?

The RSSI, or received signal strength indication, is a meter to identify the signal to
noise ratio in a 0-100 format. Any number above 20 is an acceptable link. Further
alignment or channel changes may be necessary to raise the RSSI figure.

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

D. BASIC – WIRELESS

Turbo mode, frequency channel selection (over-riding the exterior switch) and
encryption is enabled/configured on the Basic/Wireless page. See next page for details.

14

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

1. Basic Wireless Settings
Super Mode, or configuring the WES for additional throughput capability, is
enabled here. The WEM must be set to channel 4 or 6 (or 5765 or 5805 MH z)
in order for Super Mode Enable to save successful ly. The rotary switch can be
overridden to select the frequency without gaining physical access to the WEM.

SUPER MODE
Super Mode without Turbo= up to 30 Mbps
Super mode with Static Turbo A= up to 50+ Mbps. Both rates can be achieved
in an ideal environment with clear line-of-sight and no 5 GHz interference.
To achieve super mode, additional throughput is gained by obtaining it from
adjacent channels. Therefore, when 5765 Turbo A is enabled (configuring
Turbo A while set to 5765 MHz), 5745 and 5785 are not available for use. In
addition, if another WES system is configured to 5745, 5765 or 5785, it will
conflict with a Turbo A 5765 WES link. The same can be said for a Turbo A link
on 5805 however affected frequencies would be 5785 and 5825 since those
are the neighboring frequency selections to 5805 MHz.

CHANNEL SWITCH OVERRIDE
A drop down list of frequencies will appear. Make sure that if changing
frequencies using a connected wireless link, the channel on the opposite end is
configured first. For units w ith the 25.5 dBi jumper ON, selecting 5280, 5300
or 5320 will default to 5745 as on ly 5745-5825 is av ailable.

2. Wireless Security Mode
The WES can be configured to various forms of wireless enc ryption and
ciphers. The standard default is WPA2 AES which is the highest grade of
encryption and cipher combinati on available in this system.

WIRELESS SECURITY MODE
Default set to WPA. Select WEP or none if needed in order to reduce overhead.

When WPA is selected (default), the box shown on the previous page wi ll
appear to select WPA or WPA2 as well as the desired cipher type.

PRE-SHARED KEY
In order to connect with one anot her, each device in line must have the
identical pre-shared key. If this is changed and the record is are lost/forgotten,
the configurations must be returned to defaults (see page 18).

Wireless encryption and pre -shared keys must matc h in order to associate a
Client with its Host AP.

15

FAQ: Is it possible for someone with a laptop WiFi connection
to gain access to the WES Host AP?

While the WES is an 802.11a Wireless Ethernet signal, it is not a
broadcast WiFi signal. The atta cker’s WiFi AP list may show the KBC
WES Host AP but they would be required to (1) use the same
frequency, (2) identify the WES Host AP (which is disguised), (3) be
able to break the encryption method and (3) determine o r break the
pre-shared key. Using WPA2 AES will protect against such attacks.

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

E. BASIC – ETHERNET

The network settings page is used to configure the IP address, subnet mask,
and/or default gateway of the Host or Client.

ETHERNET SETTINGS
IP Address Mode: Select static and configure. Or select DHCP if connected to a

DHCP router.

IP Address: Configure LAN IP address. The subnet of the Host and Client

must match one another.

Subnet Mask: Configure subnet filter

Default Gateway: Configure default gateway if there is an external network to

which to connect.

16

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

F. ADVANCED – ADMIN

This section of the advanced tab is used for changing the password and device
name for the Host and/or Client.

ADMIN PASSWORD
To change the password, type in the desired password chan ge and confirm. Record
all password changes as there are no ways to reset to default later if the password
is lost or forgotten.

ADMINISTRATION
The device name can be changed here. Each unit does not have to have a
matching device name in order to associate. This name will appear on the status
info and Locator tool. The web idle time out will return the web browser back to the
log in screen.

17

FAQ: How can I return the unit to defaults if I cannot access
the GUI interface?

If the password to the interface is changed and no record was kept,
unfortunately it must be returned to KBC for a hard reset. There is no
“back door” default to the system in order to protect against an
attacker with knowledge of such a reset function.

All password changes must be recorded and kept in an

accessible place for future reference.

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

G. ADVANCED – SYSTEM
To reboot the system and/or bring to default settings, visit the system page of the
Advanced tab.

SYSTEM COMMANDS
Reboot to save any changes applied while recon figuring the system. A reboot
button appears after a saved change so it is not required to come to the
Advanced/System page of the interface.

If the firmware is updated, a restore to defaults may be necessary. Defaults are as
follows:

GUI Password: admin (all lower case)
LAN IP: 192.168.1.200 (Host); 192.168.1.201 (Client)
Subnet Mask: 255.255.255.0
Gateway: 192.168.0.1
Frequency Selection: Use Rotary Switch (which ever channel selection is made on
the switch)
Super Mode: Disabled
Encryption & Cipher: WPA-2; AES
Device Name: WES SP Host; WES MP Host; WES Client (depends on software type)

18

Wireless Ethernet PtP & MP System Operations Manual

ADVANCED OPERATION (CONTINUED)

H. ADVANCED – FIRMWARE
This page is used to flash firmware updates when necessary.

FIRMWARE INFORMATION
Current firmware is 7.06 for all units using channel selector switches that have 8
positions (0-7). Current firmware for older 10 position (0 -9) switches is 7.05

FIRMWARE UPGRADE

If you receive a firmware update file from KBC, save to an accessible

place to upgrade when connected to the unit. Click “Browse ” and double ­click the saved file. Then click “Upload”. Wait for the timer t o count down

as the upgrade process takes place. Then re-acces s the device on its

former IP address. Click “Advanced” and then “System” and restore the

unit to factory defaults (see previous page 18) for default configurations.

19

Wireless Ethernet PtP & MP System Operations Manual

WES CONFIGURATION TABLE

KBC recommends that a spreadsheet of the wireless system be kept on hand for
reference. A worksheet providing all of the default settings is included in the shipment.
These settings along with any changes should be kept and tracked in a format similar to
the example provided below:

S/N

Device

Name

Type

IP

Channel &

Frequency

GUI

Password

08516

Head End 1

SP Host

192.168.1.200

0; 5745

abcsecurity

08517

PTZ Cam

Client

192.168.1.201

0; 5745

abcsecurity

08518

Head End 2

MP Host

192.168.1.202

7; 5825

abcsecurity

08519

Plate
Camera

Client
Patch

192.168.1.203

7; 5825

abcsecurity
08520

Front Gate

Client

192.168.1.205

7; 5825

abcsecurity

Configurations shown above are not default settings. Information shown only to
indicate what should be recorded when changes are ma de to the default settings.

20

Wireless Ethernet PtP & MP System Operations Manual

WES SPECIFICATIONS

For product improvement, design and specifications are subject to change without notice.

RF MODULES

Power Output 50 W EIRP @ 5.8 GHz (maximum)
Transmitting Frequency 5725 – 5825 MHz (U-NII-3 ISM)
Channel Capacity 5 non-overlapping channels
5745, 5765,5785, 5805, 5825 MH z
Modulation OFDM
Latency <10 milliseconds
Sensitivity -82 dBm fir maximum data rate
Polarization Linear, vertical only
Antenna Type & Gain Omni (WAPOM, WSUOM): 2.5 dBi @ 5.8 GHz
Small patch (WES-2500; WAP, WSU): 7.8 dBi @ 5.8 GHz
Large patch (WES-2-4; WSUP): 16.7 dBi @ 5.8 GHz
Small patch in 18 inch parabolic dish: 24 dBi @ 5.8 GHz
Beam Width Omni: 360⁰; Small Patch: 90⁰; Large Patch: 24⁰; Dish: 8⁰
Data Throughput Rate Up to 20 Mbps, Standard Mode; Up to 50+ Mbps, Super

Mode

FCC ID JRRWES
IC 4887A-WES

MANAGEMENT
Interface 10/100 Base T, half/full duplex, rate auto-negotiated (802.3

compliant)

Frequency Selection Physical: 8-position rotary switch; Software: pull down and

select manual switch override capability (see pages 1 4-15)

Web browser GUI Password protected internal web browser interface

configuration pages. Compatible with Internet Explorer and

Mozilla Firefox.

Access Method Time division duplexing/Time division multiple access

(TDD/TDMA)

Protocols Used IPV4, UDP, TCP, ICMP, Telnet. HTTP. FTP, SNMP. Network

management: http

MECHANICAL
Physical Environmentally protected, billet aluminum, powder c oated

housing with UV stabilized PVC radome

Dimensions (WES-2500 individual modules; WAP, WSU): 92.68 mm x

44.55 mm x 91.69 mm; (WES -2-4 individual modules,

WSUP): 170.48 mm x 54.55 mm x 170.48 mm; (WAPOM,

WSUOM): 91.61 mm x 91.68 x 50.26 mm

Weight (WES-2500 individual modules, WAP, WSU): 0.4 Kg; (WES-

2-4 individual modules, WSUP): 0.7 Kg; (WAPOM, WSUOM ):

0.4 Kg

POWER
Power Requirements 12-20 VDC @ 3 W (Reverse voltage protected
Power Method Power over Ethernet, mid-span compliant via power injec tion

module (PIM)

Connector RJ-45, in & out of PIM as well as into LAN port of WEM
Cable Specifications 100 meters max, 24 AWG Cat5e recommended

21

Wireless Ethernet PtP & MP System Operations Manual

WES PRODUCT SPECIFICATIONS

For product improvement, design and specifications are subject to change without notice.

RF MODULES (CONTINUED)

ENVIRONMENTAL
Humidity 95% non-condensing
Operating Temperature -40⁰ C to +80⁰ C (-40⁰ F to + 18 0⁰ F)

802.11b: -95dB@1Mbps, -94dB@2Mbps, -92dB@5.5Mbps,

-90dB@11Mbps

802.11g: -90dB@6Mbps, -89dB@9Mbps, -87@12Mbps,

-85dB@18Mbps, -82dB@24Mbps,-79dB@54Mbps

POWER INJECTION MODULE (P IM)

MECHANICAL
Physical Plastic housing, not weatherproof
Dimensions 2.6” x 2.6” x 1.1”
Weight 2.5 oz
Interface 2 – RJ-45 LAN Port connector s

POWER
Voltage In 12-20 VDC, not 802.3af compliant
Power Method mid-span compliancy
Power Indicator Green on/off LED
Connector DC Jack for barrel type connector, 2.5 mm x 5.5 mm cente r

positive

ENVIRONMENTAL
Operating Temperature -40⁰ C to +80⁰ C
Humidity non-weatherproof, must be housed

Warranty

2 YEAR LIMITED WARRANTY (SEE PAGE 24 FOR DETAILS)

22

Wireless Ethernet PtP & MP System Operations Manual

TROUBLE-SHOOTING

Problem

Suggestion

No link activity

- No power from connected device. Make sure the connected
Ethernet/IP device is powered.

- Check all cables and connectors.

- Make sure the cable run between the WEM and Ethernet
device is no longer than 100 meters.

- Verify cable connection “P+ Data Out” to WEM

- Check cable type and configuration (as detailed on page 8)

Problem

Suggestion

No signal level LED
or flashing signal
level LED

- Check line-of-sight of the WEMs. Verify the WEMs are aimed
properly. You should have clear, wide-open line of sight between
the WEM modules.

- Try a different frequency and cycle power.

- Verify sufficient voltage into each PIM.

- If MP Host, the green LED should flash (see page 5)

Problem

Suggestion

All three solid LEDs
but no video

- Check video at the camera

- Check wiring into encoders or decoders

- Try a different frequency and cycle power.

- Connect one WEM directly into a PC or laptop and verify that
the IP address is accessible. Che ck the other WEM(s) the same
way, then verify that each IP address is accessible over the
wireless link into a PC/laptop.

- Verify the connected Ethernet/IP device is configured corre ctly.
If in use, encoders and decoders must be paired up correctly.

Problem

Suggestion

Video drops in and
out; recovers on its
own

- Weak signal strength (check rate and RSSI from “Client List” in
the Host GUI interface).

- Realign antennas. Make sure alignment is done in an “up/down”
& “left-to-right” format in very small increments. Align up or
down until the strongest RSS I (KBC recommends at least a 20 or
above number for RSSI). Then tighten the mounting. Then move
left/right in order to achieve the highest RSSI and a stable 54
rate. Problem

Suggestion

Low RSSIs (signal
strengths)

- Try another frequency

- Make sure clear line-of-sight to intended radio

- Re-align the antennas. See note above regarding alignment.

- Try higher gain antenna options

Further assistance is available by contacting KBC at 888-366-4276 Monday-

Friday 8am-5pm Pacific Time for technical support. Or anytime via

[e-mail] E-mails are followed up before the end of

the following regular business hou rs.

23

Wireless Ethernet PtP & MP System Operations Manual

WARRANTY INFORMATION

KBC extends the following LIMITED WARRANTY to the original owner/purchaser of this
product as follows:

- Two years from the date of initial sale for all wireless and network products.

- Five years from the date of initial sale for all fiber products.

1) If, within the specified warranty period, this product, or any part or portion thereof,

shall prove upon examination by KBC, to be defective in material or workmanship,

KBC will repair or replace such part or portion at KBC’s option. The warranty

period on the repaired or replaced part or portion of this product shall be limited to
the unexpired term of the original warranty. The buyer shall be responsible for all
shipping and transportation of the product to KBC for any performance under this
warranty.

2) Conditions and Exceptions:
a) Any accident to this product, any misuse or abuse, alternation, use in modified

form, or any attempt to repair this product shall void this warranty. These
conditions to the warranty include, but are not limited to, incorrect power
connections, physical damage due to mechanical shock, exposure to mo isture,
and circuit modification.

b) SHOULD TH IS PRODUCT PROVE DEFECTIVE FOLLOWING PURCHASE, THE

BUYER, NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER, ASSUMES
THE ENTIRE COS T OF ALL SERVICING OR REPAIR, EXCEPT AS OTHERWISE
PROVIDED BY THE TERMS OF THIS WARRANTY.

c) FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY ON THIS PRODUCT,

THE BUYER IS LIMITED TO THE FOLLOWING DAMAGES. (1) THE COST OF
LABOR TO REPAIR OR REP LACE DEFECTIVE PARTS OR PORTIONS OF TH IS
PRODUCT, AND (2) THE COST OF THE REPAIRED OR REPLACE PARTS OR
PORTIONS OF THIS PRODUCT.

d) NO OTHER EXPRESSED OR IMPLIED WARRANTIES HAVE BEEN MADE OR WILL

BE MADE ON BEHALF OF KBC W ITH RESPECT TO T HE SALE, REPAIR,
INSTALLATION, OPERATION, OR REPLACEMENT OF TH IS PRODUCT. KBC
DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OF THIS
PRODUCT OR ITS F ITNESS FOR ANY PURPOSE, AND THE BUYER AGREES THAT

THIS PRODUCT IS SOLD “AS IS” AND THAT THE EN TIRE RISK OF QUALITY

AND PERFORMANCE OF THIS PRODUCT IS WITH THE BUYER, EXCEPT AS
OTHERWISE PROVIDED BY THE TERMS OF THIS WARRANTY.

e) Some states/jurisdictions do not allow exclusion s or li mitations of incidental o r

consequential damages, or limitations on how long an implied warranty lasts,
so the above exclusions or lim itations may not apply to you.

f) If you do not wish to be bound by any of the provisions in this
warranty, please return the product(s) immediately.

3) Contact your dealer regarding return authorizations for out of
warranty repairs and any further product information.

24

Wireless Ethernet PtP & MP System Operations Manual

APPENDIX

The appendix section is an additional segment of the manual that provides information
on proper wireless installation .

TECHNICAL RECOMMENDATIONS – WES PtP/MP INTEGRATION

The following section of the appendix will help to ensure long term weatherproofing of
the WES modules.

LAN PORT WEATHERPROOF STRAIN RELIEF
Each WES kit includes a strain relief which will protect the LAN port and RJ -45
connector on the underside of the WEM. Ensure that each WEM has its strain relief
connected to the LAN port.

CAT5 CABLES
All exterior cabling should be outdoor rated Cat5e or 6. All cables should be pulled
through conduit if otherwise exposed. Indoor rated Cat5 or 6 can get brittle or the
connectors can corrode over time.

FURTHER PROTECTION
Silicon sealing can trap moisture condensation on open ports to the WEM. Do not over
seal the LAN port. Keep silicon protection minimal (with strain relief connector) so tha t
moisture is able to release. Silicon should not be use d in lieu of proper weatherproof
seals.

POWER OVER ETHERNET
The WES is not 802.3af compl iant and requires the PIM which injects 12 volts DC. The
PIM should be located in a place that can be reached easily (in case of need to cycle its
power), however, within a reasonable length of cable (~50 meters) to the WEM to
avoid voltage issues.

ACCESSIBILITY
The WEM should be mounted high enough to achieve clear line-of-sight to the next
WEM. It is recommended to place the PIM or switch at a location that is access ible
without the need of a lift truck or large ladder. All products should be kept from foreign
accessibility so that an attacker cannot interfere with the security products.

COMMAND PROMPT COMMANDS

During set up and/or trouble-shooting, KBC recommends using the Command Prompt
as the IP locating tool for the nodes. A regular ping will result in 4 replies. The following
commands are also useful:

Command Function
ping (IP Address) Response from Ethernet device at IP address
ping (IP Address) -t Constant response from Ethernet device at IP address

arp -d * Recommended command to flush the arp table

ipconfig Identifies the TCP/IP settings of the computer

A-1

Wireless Ethernet PtP & MP System Operations Manual

APPENDIX

SYSTEM INSTALLATION NO TES

Remote Location #1

Device

S/N

Host / Client

IP Address

Radio MAC Address

Remote Location #2 / Head End Location in Single Point-to-Point Application

Device

S/N

Host / Client

IP Address

Radio MAC Address

Remote Location #3

Device

S/N

Host / Client

IP Address

Radio MAC Address

Remote Location #4

Device

S/N

Host / Client

IP Address

Radio MAC Address

Head End Location

Device

S/N

Host / Client

IP Address

Radio MAC Address

A-2