KBC ESUG8P User Manual

Download

Ethernet Switch

ESUG8P

User Manual

Ethernet Switch User Manual

TABLE OF CONTENTS

1 OVERVIEW ................................................................................. 3

1.1

NTRODUCTION

............................................................................................ 3

1.1.1 ESUG8P ............................................................................................. 3

1.2

ECHNICAL SPECIFICATION

.............................................................................. 4

2 INSTALLATION ............................................................................. 5

2.1

ACKAGE CONTENTS

2.2

ONFIGURATIONS

2.2.1 Physical Connections ........................................................................... 6

2.3

NSTALLATION METHOD

2.3.1 DIN Rail Mount ................................................................................... 7

2.3.2 Wall-mount ........................................................................................ 7

2.4

2.5

2.6

2.7

2.8

THERNET

OWER CONNECTIONS

AULT ALARM CONTACT

DIP S

LED S

RJ45 C

WITCH FUNCTION

TATUS

............................................................................................... 9

...................................................................................... 5

......................................................................................... 5

................................................................................... 7

ONNECTIONS

.................................................................................... 8

................................................................................... 8

.................................................................................. 9

......................................................................... 7

3 TROUBLESHOOTING .................................................................... 10

3.1

ELF-TESTING

........................................................................................... 10

4 SYSTEM EXAMPLE ....................................................................... 11

5 DIMENSIONS ............................................................................. 11

6 WARRANTY .............................................................................. 12

6.1

6.2

6.3

ARRANTY INFORMATION

LASS A

FCC ....................................................................................................... 13

ITE ............................................................................................ 13

.............................................................................. 12

7 INSTRUCTION OF DISASSEMBLY ...................................................... 13

Ethernet Switch User Manual

1 Overview

1.1 Introduction

This manual covers the ESUG8P series. KBC Networks’ ESUG8P products are high performance, unmanaged, eight gigabit port industrial PoE Ethernet switches designed for use in a wide range of operating temperatures in nonenvironmentally conditioned, industrial applications. The units have redundant power supply terminals and an alarm output. All copper ports are automatically configured and the plug-and-play design provides ease and speed of installation.

1.1.1 ESUG8P

The ESUG8P provides connectivity for up to eight, 10/100/1000 RJ45 twisted pair copper ports, with all eight ports capable of simultaneously supplying IEEE802.3at PoE. Each port supports a self-adaptive function allowing it to be configured to 10Base-T or 100Base-TX, full or half duplex operation mode. It is available as either DIN rail or wall-mount configurations.

Ethernet Switch User Manual

1.2 Technical Specification

Switching

Mode Store-and-forward

Switching rate 14,881pps, 148,810pps, 1,488,100pps

Backplane switching bandwidth 16Gbps

Mac address table 2k

ESUG8P

Ports

Copper

Physical port 8 x shielded RJ45

RJ45 port 10BASE-T/100Base-TX/1000Base-T

Auto-negotiation

Standard IEEE 802.3

Transmission distance <100m

PoE

Physical port 8 x shielded RJ45

Standard IEEE 802.3at

Power supplied (per port) 30W @ +50Vdc

Electromagnetic compatibility

Interference EN55022 Class A

Immunity IEC61000-6-2

Power

Input voltage

Power consumption

Power supply Supplied separately

50 - 57Vdc

8W (no PoE) 250W ( full load PoE)

Environmental

Operating temperature -40°C - +74°C / -40°F - +165°F

Storage temperature -40°C - +74°C / -40°F - +165°F

Relative humidity 5% - 95%, Non-condensing

Mean Time Between Failure >300,000 hours

Mechanical

Dimensions (W x H x D) 27mm x 145mm x 95 mm

1.07” x 5.71” x 3.74”

Protection class rating IP30

Weight

390g

13.75oz

Ethernet Switch User Manual

2 Installation

2.1 Package Contents

• Ethernet switch fitted with DIN rail mount.

• 2 x Wall-mount brackets with screws

• Pluggable terminal block

• Quick Start Guide

Note: A 50 – 57Vdc PSU is required but supplied separately.

Please contact you dealer or distributor if a part is missing or damaged.

2.2 Configurations

Products are available in either DIN rail or wall-mount packages, with the following configurations:

Product Type DIN Rail Wall-mount

ESUG8P

 

Ethernet Switch User Manual

Front View

2.2.1 Physical Connections

Ethernet Switch User Manual

2.3 Installation Method

2.3.1 DIN Rail Mount

• Remove all packaging material.

• Attach the device to a DIN rail.

• Attach copper cables as required.

• Insert the male power block (attached to the supplied in-line PSU) to the

female power socket on the device and tighten the terminal locking screws

using a flathead screw driver.

See Section 2.7 for LED status.

2.3.2 Wall-mount

• Remove all packaging material.

• Unscrew the DIN rail mounting plate from the switch taking special care to

retain the 3 screws using a Phillips No.1 or No.2 screwdriver.

• Attach the supplied wall mount plates to the switch using the screws that

have just been removed from the DIN rail mounting plate with a Phillips

No.1 or No.2 screwdriver.

• Position the unit on the required, flat surface and secure with screws via the

mounting plate holes. Screws are not provided.

• Attach copper cables as required.

• Insert the male power block (attached to the supplied in-line PSU) to the

female power socket on the device and tighten the terminal locking screws

using a flathead screw driver.

See Section 2.7 for LED status.

2.4 Ethernet RJ45 Connections

Each RJ45 port is adaptive and supports auto MDI/MDI-X connection. They can be connected by straight through or cross-over cables to terminal devices, servers, hubs or other switches. Each switch supports IEEE802.3x and IEEE802.3ab so the optimum transmission mode (either half-duplex or full-duplex) and data rate (10Mbps, 100Mbps or 1000Mbps) will be selected automatically.

Ethernet Switch User Manual

24Vdc, 1A resistance

2.5 Power Connections

A 6 pin, power terminal block should be used to connect the power cable to the unit.

Figure 2.1 Power connections

Contact number Connections

1 PWR2: -

2 PWR2: +

3 Fault alarm contact

4 Fault alarm contact

5 PWR1: -

6 PWR1: +

Note:

otherwise the Power Fault Alarm will be lit.

If only using one power source, connect pin 1 to pin 5 and pin 2 to pin 6

2.6 Fault Alarm Contact

The fault alarm contacts are in the middle of the 6 pin, screw block terminal on pins 3 &

4. An open circuit will occur if a power failure is detected.

Load

P-Fail

External power

Fig 2.2 Fault Alarm Contacts

Ethernet Switch User Manual

2.7 DIP Switch Function

DIP-1

DIP-2 Description

OFF OFF Power failure relay alarm & P-Fail disabled

ON OFF P1 failure: relay alarm & P-Fail enabled

OFF ON P2 failure: relay alarm & P-Fail enabled

ON ON P1 or P2 failure: relay alarm & P-Fail enabled

2.8 LED Status

LED Status Description

P-Fail

OFF

Power is supplied to the unit

No power to the unit

Power is supplied to the unit

No power to the unit

Power to P1 or P2 has failed

Power is functioning to both or none of the powered devices

Ethernet RJ45 Port Status LED

Each RJ45 Ethernet port has two green indicators. The lower green lamp indicates whether power is being supplied to a PD and the upper green lamp indicates port link state.

Green (lower)

Green (upper)

OFF

FLASH

OFF

The port is supplying power to the powered device

There is no powered device attached or the power to the device has failed

Effective network connection has been established for the port

Data traffic is passing through the port

No effective network connection has been established for the port

Ethernet Switch User Manual

3 Troubleshooting

3.1 Self-testing

When the device is powered on, the top green LED on the RJ45 ports will flash once

then go out, the bottom green LED on the RJ45 will light in succession, starting at P1

to P8, each port will continue to light in turn unless it is connected to an external

device. The power (P1 & P2) and P-Fail LEDs will be lit according to the power being

supplied to the unit and the DIP switch selection (see Section 2.7).

If problems are encountered when using this Ethernet switch please check the

following:

• Verify that the correct power supply unit is being used; this unit requires a

48Vdc supply.

• Ensure that the correct cables are being used to construct your network:

o Unshielded Twisted Pair or Shielded Twisted Pair for RJ45 connections

o 100Ω Cat 3 cable or above for 10Mbps connections

o 100Ω Cat 5 cable or above for 100Mbps connections

o 100Ω Cat 5e cable or above for 1000Mbps connections

o Twisted pair connection must not exceed 100m (328 feet)

• See section 2.7 for LED status indicators.

Ethernet Switch User Manual

WESII

Power

Up to 7 IP Cameras

8 Port

4 System Example

(IEEE 802.3at Compliant powered)

Switch

Client

5GHz

Injection Module

Figure 4.1 ESUG8P Typical System Application

5 Dimensions

Ethernet Switch User Manual

6 Warranty

6.1 Warranty Information

KBC extends the following LIMITED WARRANTY to the original owner/purchaser of this product as follows:

- Five years from the date of initial sale for Ethernet switches.

- Two years from the date of initial sale for all wireless and other network products.

- Five years from the date of initial sale for all fiber products.

1) If, within the specified warranty period, this product, or any part or portion thereof, shall prove upon examination by KBC, to be defective in material or workmanship, KBC will repair or replace such part or portion at KBC’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty. The buyer shall be responsible for all shipping and transportation of the product to KBC for any performance under this warranty.

2) Conditions and Exceptions: a) Any accident to this product, any misuse or abuse, alternation, use in modified

form, or any attempt to repair this product shall void this warranty. These conditions to the warranty include, but are not limited to, incorrect power connections, physical damage due to mechanical shock, exposure to moisture, and circuit modification.

b) SHOULD THIS PRODUCT PROVE DEFECTIVE FOLLOWING PURCHASE, THE BUYER,

NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER, ASSUMES THE ENTIRE COST OF ALL SERVICING OR REPAIR, EXCEPT AS OTHERWISE PROVIDED BY THE TERMS OF THIS WARRANTY.

c) FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY ON THIS PRODUCT, THE

BUYER IS LIMITED TO THE FOLLOWING DAMAGES. (1) THE COST OF LABOR TO REPAIR OR REPLACE DEFECTIVE PARTS OR PORTIONS OF THIS PRODUCT, AND (2) THE COST OF THE REPAIRED OR REPLACE PARTS OR PORTIONS OF THIS PRODUCT.

d) NO OTHER EXPRESSED OR IMPLIED WARRANTIES HAVE BEEN MADE OR WILL BE

MADE ON BEHALF OF KBC WITH RESPECT TO THE SALE, REPAIR, INSTALLATION, OPERATION, OR REPLACEMENT OF THIS PRODUCT. KBC DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OF THIS PRODUCT OR ITS FITNESS FOR ANY PURPOSE, AND THE BUYER AGREES THAT THIS PRODUCT IS SOLD “AS IS” AND THAT THE ENTIRE RISK OF QUALITY AND PERFORMANCE OF THIS PRODUCT IS WITH THE BUYER, EXCEPT AS OTHERWISE PROVIDED BY THE TERMS OF THIS WARRANTY.

e) Some states/jurisdictions do not allow exclusions or limitations of incidental or

consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

f) If you do not wish to be bound by any of the provisions in this warranty, please

return the product(s) immediately.

3) Contact your dealer regarding return authorizations for out of warranty repairs and any further product information.

Ethernet Switch User Manual

6.2 Class A ITE

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

6.3 FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful Interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense.

7 Instruction of Disassembly

Instruction of Disassembly of KBC Product

(For EU Directive 2002/95/EEC-WEEE)

Tools required:

• No. 1 Phillips screwdriver

• No. 2 Phillips screwdriver

Steps for disassembly:

1. Remove tightening screws of box cover (8 screws).

2. Remove cover plate.

3. Remove tightening screws for printed circuit board (PCB).

4. Take out all PCBs.

Notice: When a product reaches the end of its life – return to KBC.

data delivered

KBC Networks

25691 Atlantic Ocean Drive

Suite 3B

Lake Forest, CA 92630

U.S.A

Americas

Phone: 1-949-297-4930

Fax: 1-949-297-4933

KBC Networks Ltd., EMEA

KBC Networks Ltd.

Barham Court

Teston, Maidstone

Kent, ME18 5BZ

United Kingdom

Phone: +44(0)1622 618787

Fax: +44(0)20 7100 8147

Email:

Web: www.kbcnetworks.com

info@kbcnetworks.com

KBC ESUG8P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual