Kaz HZ-7040, HZ-7010, HZ-7000, HZ-7030, HZ-7020 User Manual
PO
W
E
R
MO
D
E
PRECISION HEAT
TM
DIGITAL HEATER FAN
HZ-7000, HZ-7010, HZ-7020, HZ-7030,
HZ-7040 Series
IMPORTANT
SAFEGUARDS
READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS
HEATER.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the
following:
IMPORTANT
INSTRUCTIONS
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns , do not
let bare skin touch hot surface. If provided, use handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet (0.9 m)
from the front of the heate r and keep them away f rom
the sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left oper ating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heat er malfunctions, has been
dropped or damaged in any manner. Return heater
to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist indoor lo ca tions. Never
locate heater where it may fa ll int o a bat ht ub or ot her
water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or the like. Arrange cord
away from traffic areas wh ere it will not be tripped
over.
9. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of shock,
this plug is intended to fit onl y one way in a polar iz ed
outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
safety feature.
10. This heater draws 12.5 amps during operation. To
prevent overloading a circuit, do not plug the heater
into a circuit that already has other appliances working.
11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet (receptacle) and plug may cause overheat ing and distortion
of the plug. Contact a qualified electrician to replace
loose or worn outlet.
12. To disconnect the heat er, first turn controls to the
OFF position, then grip the plug and pull it from the
wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or da mage the heater.
14. To prevent a p os sible f ire, do not b lock ai r i nta kes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked .
15. A heater has hot and ar cing o r spark ing p arts inside.
Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stor ed.
16. Use this heater only as described in this manual.
Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
17. Avoid the use of an exte nsion cord because the
extension cord may overh eat and cau se a risk of f ire.
However, if you have to use an extension cord, th e
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
18. The output of this heater may vary and its temperature may become intense enough to burn exposed
skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to
react to avoid burns.
SAVE THESE
19.
DO NOT attempt to defeat th is
INSTRUCTIONS.
1
BASIC CONTROL PANEL OPERATION:
MODE: SET TIMER
Timer
POWER
Continuous Run
Power
Mode
F/C
• Press Power once to start the heater on High Power,
Continuous Run.
• Press Power again to change to Low Power, Continuous
Run.
• Press Power a third time to turn the heater off.
MODE: SET TEMPERATURE
Temperature
Power
Mode
Power
Mode
F/C
• Press Mode until the Timer icon blinks. The Hour
display will appear
• Use the Up or Down arrows to set an operation time
between 1 and 10 hours.
• The heater will turn-off when time runs out.
FAHRENHEIT/CELSIUS
Power
Mode
F/C Temperature
Display
F/C
F/C
• Press Mode until the Temperature icon blinks. The
current room temperature will appear.
• Use the Up or Down arrows to set the desired temperature.
• The Temperature icon will stop blinking and the current room temperature will reappear after the
desired temperature is set.
• The heater will turn-off shortly after the desired temperature is reached and the Power light above the
display will blink.
• The heater will turn back on when the room temperature drops approximately 2 degrees below the
desired temperature. The Power light will stop
blinking and will remain lit.
• F/C feature functions from only the Power or Set
Temperature screens.
• Press the F/C button to toggle between Fahrenheit
and Celsius.
OSCILLATION (HZ-7020, HZ-7030, HZ-7040
SERIES)
Power
Mode
Oscillation
• The Oscillation feature functions in any power or
mode setting.
• Press the Oscillation button to toggle this feature on
and off.
2
F/C
Loading...