KAZ HZ-341 User Manual
DIGITAL CERAMIC HEATER
Model HZ-339 Series
Model HZ-341 Series
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns,
do not continually let bare skin touch hot
surfaces. If provided, use handle when moving
this heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and
curtains at least 3 feet (0.9 m) from the front of
the heater and keep them away from the sides
and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord
or plug or after the heater malfunctions, has been
dropped or damaged in any manner.
6. Do not use outdoors.
7. This heater is rated at 1500W, 120 VAC. It is
intended for use on tabletops or desktops and
floors. It is not to be used in wet or moist
locations, such as bathrooms and laundry areas.
If an extension cord must be used, it must be 14
gauge or larger and rated no less than 1875
watts.
8. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners, or the like.
Arrange cord away from traffic area where it will
not be tripped over.
9. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of
shock, this plug is intended to fit only one way in
a polarized outlet. If the plug does not fit
securely in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature.
10. This heater draws 12.5 amps during operation
when in the high setting. To prevent overloading
a circuit, do not plug the heater into a circuit that
already has other appliances working.
11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet
(receptacle) and plug may cause overheating and
distortion of the plug. Contact a qualified
electrician to replace loose or worn outlet.
12. To disconnect the heater, first turn controls to the
OFF position, then grip the plug and pull it from
the wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes
or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may
become blocked.
15. A heater has hot and arcing or sparking parts
inside. Do not use it in the areas where gasoline,
paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual.
Any other use not recommended by the
manufacturer may cause fire, electric shock, or
injury to persons.
17. The output of this heater may vary and its
temperature may become intense enough to burn
exposed skin. Use of this heater is not
recommended for persons with reduced
sensitivity to heat or an inability to react to avoid
burns.
18.
SAVE THESE
INSTRUCTIONS
The Honeywell trademark is used by Kaz, Inc. under license from Honeywell Intellectual Properties, Inc.
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 1
This heater is equipped with SureSet™Digital Controls that provide the ability to set the temperature to the
exact degree desired. To operate, simply follow these instructions.
STEP 1: POWER
• Press the Power button ( ) once to start the heater on High
Power ( ), Continuous Run ( ) (Fig. 1). If left at this setting,
the unit will run continuously on High Power (1500 watts, 12.5
amps) and will not shut off until the unit is manually turned
off.
• Press the Power button ( ) again to change to Low Power ( ),
Continuous Run ( ). If left at this setting, the unit will run
continuously on Low Power (900 watts, 7.5 amps) and will not
shut off until the unit is manually turned off.
• Press the Power button ( ) a third time to turn the heater OFF.
NOTE: If operated at the Low setting, the heater will not provide as much heat output as in the High
setting, however, the Low setting will not require as much electrical current to operate. To avoid
overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
STEP 2: SET TEMPERATURE
• Press the Temp/Timer button ( ) until the Temperature Icon
( ) blinks. The current room temperature will appear (Fig. 2).
• Use the Up and Down arrow buttons ( ) to set the Desired
Temperature (Fig. 2).
• The Temperature Icon ( ) will stop blinking and the current room
temperature will reappear after the Desired Temperature is set.
• The heater will turn off shortly after the Desired Temperature is
reached and the Temperature Display will blink.
• The heater will turn back on when the room temperature drops
below the Desired Temperature. The Temperature Display will
then stop blinking and will display the current room temperature.
STEP 3: SET TIMER
NOTE: This function should only be set if you desire that the heater
be automatically shut off after a certain period of time (1 to 10 hours
from the time the function is set). Always set the Desired
Temperature prior to setting the Timer (see Step 2) so that the heater
will shut off at the Desired Temperature setting and not run
continuously.
• Press the Temp/Timer button ( ) until the Timer Icon ( ) blinks. The Hour Display will appear.
The Auto Off icon will also appear (Fig. 3).
• Use the Up and Down arrow buttons ( ) to set the heater operation time between 1 and 10 hours
(Fig. 3). Once the timer function is set the hour set will remain displayed until the time set runs out.
• The heater will automatically turn off when time runs out.
NOTE: If the Desired Temperature was set prior to setting the Timer function, the heater will cycle on and
off as per the selected Desired Temperature setting. To return to the Continuous Run Mode (Fig. 1), press
the Temp/Timer button ( ) a third time.
OPERATION
Fig. 3
Fig. 2
Fig. 1
Continuous Run Icon
Temperature Icon
Timer Icon
Auto Off Icon
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 2
REMOTE CONTROL OPERATION
(MODEL HZ-341 SERIES ONLY)
Two (2) AAA batteries are included and are required to operate the
Remote Control.
The Remote Control can be stored on the heater when not in use by
hanging the remote on the hook located on the side of the heater
(See Fig. 7).
The Remote Control works the same as the corresponding buttons on
the Control Panel. The Control Panel display on the heater will show
the appropriate icons when the various functions are activated.
STEP 1: POWER
• Press the Power button ( ) once to start the heater on High
Power ( ), Continuous Run ( ) (Fig. 8). If left at this setting,
the unit will run continuously on High Power (1500 watts, 12.5
amps) and will not shut off until the unit is manually turned
off.
• Press the Power button ( ) again to change to Low Power ( ),
Continuous Run ( ). If left at this setting, the unit will run
continuously on Low Power (900 watts, 7.5 amps) and will not
shut off until the unit is manually turned off.
• Press the Power button ( ) a third time to turn the heater OFF.
OPERATION
(CONTINUED)
STEP 4: FAHRENHEIT/CELSIUS FUNCTION
This heater offers the option to read the temperature setting in either
Fahrenheit or Celsius.
• °F/°C feature functions from only the Power or Set Temperature
screens.
• Press °F/°C button to toggle between Fahrenheit and Celsius
(Fig. 4).
STEP 5: OSCILLATION
• The Oscillation feature functions in all Power and Temp/Timer
settings.
• Press the Oscillation button ( ) to
toggle this feature on and off (Fig. 5).
NOTE: This product is equipped with a
SafeGuard
™
Alert Heat Indicator Badge
(Fig 6). When the SafeGuard
™
Alert Badge
located on the top of the grill changes from
black to red the grill is hot to the touch.
Do not touch the grille until the unit has
been turned off and the SafeGuard
™
Alert
Badge has turned back to black.
Fig. 4
°F/°C Temperature
Display
Fig. 5
Fig. 8
Power
Fig. 7
Fig. 6
Heat
Indicator
Badge
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 3
REMOTE CONTROL OPERATION
(CONTINUED)
NOTE: If operated at the Low setting, the heater will not provide as much heat output as in the High
setting, however, the Low setting will not require as much electrical current to operate. To avoid
overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
STEP 2: SET TEMPERATURE
• Press the Mode button until the Temperature Icon ( ) blinks.
The current room temperature will appear (Fig. 9).
• Use the Up and Down arrow buttons ( ) to set the Desired
Temperature (Fig. 9).
• The Temperature Icon ( ) will stop blinking and the current room
temperature will reappear after the Desired Temperature is set.
• The heater will turn off shortly after the Desired Temperature is
reached and the Temperature Display will blink.
• The heater will turn back on when the room temperature drops
below the Desired Temperature. The Temperature Display will
then stop blinking and will display the current room temperature.
STEP 3: SET TIMER
NOTE: This function should only be set if you desire that the heater be
automatically shut off after a certain period of time (1 to 10 hours
from the time the function is set). Always set the Desired
Temperature prior to setting the Timer (see Step 2) so that the heater
will shut off at the Desired Temperature setting and not run
continuously.
• Press the Mode button until the Timer Icon ( ) blinks. The Hour
Display will appear. The Auto Off icon will also appear (Fig. 9).
• Use the Up and Down arrow buttons ( ) to set the heater
operation time between 1 and 10 hours (Fig. 9). Once the timer
function is set the hour set will remain displayed until the time set runs out.
• The heater will automatically turn off when time runs out.
NOTE: If the Desired Temperature was set prior to setting the Timer function, the heater will cycle on and
off as per the selected Desired Temperature setting. To return to Continuous Run Mode (Fig. 1), press the
Mode button a third time.
STEP 4: OSCILLATION
• The Oscillation feature functions in all Power and Temp/Timer settings.
• Press the Oscillation button to toggle this feature on and off (Fig. 10).
Fig. 9
Fig. 10
Down
Up
Mode
Oscillation
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 4
ELECTRICAL RATING
This product is rated 12.5 Amps (1500 watts) @ 120V, 60Hz.
CONSUMER RELATIONS
Mail questions or comments to:
Kaz, Incorporated
Consumer Relations Dept.
250 Turnpike Road
Southborough, MA 01772
Call us toll-free at: 1-800-332-1110
E-mail: consumerrelations@kaz.com
Or visit our website at: www.kaz.com
Please be sure to specify a model number.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST, RETURN
THE HEATER TO THE ORIGINAL PLACE OF PURCHASE OR SEE YOUR WARRANTY. DO NOT ATTEMPT TO
OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE
TO THE HEATER OR PERSONAL INJURY.
TROUBLESHOOTING
If your heater shuts off unexpectedly, safety features may have been activated to prevent overheating. If
this happens:
• Be sure the power cord is plugged into a working electrical outlet.
• Check your Desired Temperature setting. The unit may be off because you have reached your Desired
Temperature setting.
• Check for any obstructions. If you find one, turn the heater OFF and unplug it. Wait at least 10 minutes
to allow the heater to cool completely before removing any obstruction. When done, plug in the heater
and follow the OPERATION instructions.
CLEANING AND STORAGE
We recommend that the heater be cleaned at least once a month and before off-season storage.
• Turn the heater OFF and unplug it. Allow it to cool completely.
• Use only a dry cloth to clean the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH,
OR ANY CHEMICAL SOLUTION.
• Clean your heater using the above-mentioned steps, then pack the heater in its original container and
store in a cool, dry place.
• This heater does not disassemble.
SAFETY FEATURES
This heater is equipped with several devices and features for added protection:
• A tip-over switch that disables the heater if accidently tipped over (HZ-341BW only).
• A SafeGuard
™
Alert Heat Indicator Badge that indicates the grille is hot and should not be touched -
turns from black to red.
• A high temperature safety control prevents overheating (Hi-limit).
• A back-up thermal circuit breaker that will permanently shut down the heater should it operate at
higher than normal temperatures.
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 5
You should first read all instructions before
attempting to use this product.
A. This 5 year limited warranty applies to repair
or replacement of product found to be
defective in material or workmanship. This
warranty does not apply to damage resulting
from commercial, abusive, unreasonable use or
supplemental damage. Defects that are the
result of normal wear and tear will not be
considered manufacturing defects under this
warranty. KAZ IS NOT LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE. ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF
THIS WARRANTY. Some jurisdictions do not
allow the exclusion or limitation of incidental or
consequential damages or limitations on how
long an implied warranty lasts, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights,
and you also may have other rights which vary
from jurisdiction to jurisdiction. This warranty
applies only to the original purchaser of this
product from the original date of purchase.
B. At its option, Kaz will repair or replace this
product if it is found to be defective in material
or workmanship. Defective product should be
returned to the place of purchase in
accordance with store policy. Thereafter, while
within the warranty period defective product
may be returned to Kaz.
C. This warranty does not cover damage resulting
from any unauthorized attempts to repair or
from any use not in accordance with the
instruction manual.
D. Return defective product to Kaz, Incorporated
with a brief description of the problem. Include
proof of purchase and a $10 US/$15.50 CAN
check or money order for handling, return
packing and shipping charges. Please include
your name, address and a daytime phone
number. You must prepay shipping charges.
Send to:
In U.S.:
Kaz, Incorporated
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118
USA
In Canada:
Kaz, Incorporated
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6
Canada
© 2005 Kaz, Incorporated. All Rights Reserved.
P/N: 31IM0341192
5 YEAR LIMITED WARRANTY
HZ-339_341_OM_Rev2.qxd 6/22/05 5:15 PM Page 6
Loading...