Kaz HV-141, HV-181 User Manual

OWNER'S MANUAL

14"/18" (35CM/45CM) COMMERCIAL GRADE

STAND FAN

Model HV-141 without base weight

HV-181 with base weight

HV-181

HV-141

C O

M M

E R

C I A

L G

R A

H I G

M E D

F F

O W

C O M

E R C

IA L

G R

A D

I G

H M

E D

F F

L O

D E

READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN.

When using electrical appliances, basic safety precautions should always be followed, including the following:

• Use this fan only as described in this manual. Other use not recommended may cause fire, electric shock or injury.

• High Velocity fans are designed to create rapid air movement; therefore, make sure the fan is not placed near drapes, curtains, or any objects that may be drawn into the fan.

• To protect against electrical shock, do not immerse unit, plug or cord in water or spray with liquids.

• This fan requires a grounded 120 volt power source (3 prong receptacles).

NEVER CONNECT THIS FAN TO ANY POWER SOURCE OTHER THAN A PROPERLY GROUNDED 120 VOLT AC RECEPTACLE. DO NOT

ATTEMPT TO DEFEAT THIS SAFETY FEATURE.

• Close supervision is necessary when any appliance is used by or near children.

• Turn the fan to the OFF position and unplug the fan from the outlet when not in use, when moving fan from one location to another, servicing parts and before cleaning.

• Do not operate fan in the presence of explosive and/or flammable fumes.

• Do not place the fan or any parts near an open flame, cooking or other heating appliance.

• Do not operate the fan with a damaged cord or plug, after a malfunction or if dropped or damaged in any manner. (See warranty)

• Avoid contact with moving fan parts.

• To disconnect, grip the plug and pull it from the wall outlet. Never pull by the cord.

• The use of attachments not recommended by Honeywell Consumer Products may be hazardous.

SAFETY INSTRUCTIONS

• Always use on a dry, level surface.

• Do not hang or mount fan on a wall or ceiling.

• Do not operate without the fan grilles properly in place.

• Be sure to center this fan when using it on an elevated surface and be careful not to place the fan too close to the edge of that surface.

• Do not use outdoors.

• Do not let the power

cord hang over the edge of a table or counter or let it touch any hot surfaces.

• A loose fit between the AC outlet and plug may cause overheating of the plug. Have a qualified electrician replace the outlet.

WARNING: To reduce the risk of fire or electrical shock, DO NOT USE THIS FAN with any SOLID STATE Speed Control Device.

BASE ASSEMBLY INSTRUCTIONS

NOTE: THESE INSTRUCTIONS ARE FOR MODEL HV-141 (NO BASE WEIGHT INCLUDED/FIG. 1) AND HV-181 (WITH BASE WEIGHT/FIG. 1A).

IF YOU HAVE MODEL HV141 (Fig.1), PLEASE FOLLOW THESE INSTRUCTIONS BUT DISREGARD REFERENCES TO BASE WEIGHT.

• Remove the base extension pole, base with attached base weight (Fig.1A), #10 metric socket wrench and (5) bolts and (5) nuts from the box.

• Place the base on the floor with the weight on the bottom, line up the base extension pole holes with those in the base and firmly insert the pole into the base.

NOTE: It may be easier for you to insert and tighten each bolt individually instead of all 5 at once. Use the method you are most comfortable with.

• When you are finished attaching all (5) bolts, flip the base back over so that the base extension pole is now facing up.

• Separate the nut and metal washer from each bolt.

• Using your fingers, press one bolt through the base extension pole plate, and into the base until it is almost flush with the plate.

• Once the bolt is inserted, carefully turn over the base and pole so the base weight is facing upright.

• Take a metal washer and drop it into the hole so it fits around the bolt.

• Then take a nut and fit it into the #10 metric socket wrench (included). You may then, using the tool, thread and secure the nut around the bolt. Do not completely tighten

• Repeat for all 5 bolts, then tighten.

Fig. 1

BASE EXTENSION POLE

BASE

BOLTS

NUTS

Fig. 1A

BASE EXTENSION POLE

BASE

BOLTS

BASE WEIGHT

NUTS

WASHERS

HV-181

HV-141

• Place the metal stand fan pole into the base extension, lining up the groove of the pole to the hole in the base extension.

• Push together until the holes (in the groove) line up (Fig. 2).

•

Insert and hand tighten

the locking thumb screw.

➡

Fig. 2

➡

Fig. 3

• Unscrew the control box locking knob from the control box.

• Push the control box extension through the hole in the fan pole (Fig. 4). Be sure that the power cord from the control box to the fan is always free hanging.

• From the rear, tighten the control box holding knob. DO NOT OVERTIGHTEN.

ASSEMBLY INSTRUCTIONS

• Place the fan assembly

over the metal stand pole while lining up the groove from the fan assembly with the hole in the fan pole. Push together and line up the holes (Fig. 3).

• Insert the fan locking thumb screw and hand tighten.

➡

Commercial

Grade

Fig. 4

OPERATION

• Set your fan on a level, dry surface.

• Plug the power cord into a grounded three prong wall outlet.

• Select the desired speed for your needs

• Tilt the fan assembly to the desired air direction.

• For maximum circulation, you may point the fan toward the

ceiling and get the maximum air turbulence (Fig. 5). Using this method in the summer will circulate air providing a “wind chill” effect, and in the winter will move the warm air from the ceiling, dispersing it and giving you a more uniform room temperature.

Fig. 5

+ 8 hidden pages