KAZ HS-120, HS-120C User Manual

OWNER’S MANUAL

12" ( 30 CM) TURBO

4 WAY FAN

12" ( 30 CM) TECH

4 WAY FAN

Model HS-120 Series

Model HS-120C Series

INSTRUCTIONS F0R USE AND CARE

READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN.

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

Use this fan only as described in this manual. Other use not recommended may cause fire, electric shock or injury to persons.

2. This product is intended for household use

ONLY and not for commercial, industrial or outdoor use.

3. To protect against electric shock, do not place fan in window, immerse unit, plug or cord in water or spray with liquids.

4. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

DO NOT

attempt to defeat this safety feature.

5. Close supervision is necessary when any appliance is used by or near children.

6. Turn the fan to the OFF position and unplug the fan from the outlet when not in use, when moving the fan from one location to another and before cleaning.

7. To disconnect the fan, grip the plug and pull it from the wall outlet. Never pull by the cord.

8. Do not operate the fan in the presence of explosive and/or flammable fumes.

9. Do not place the fan or any parts near an open flame, cooking or other heating appliance.

10. Do not operate the fan with a damaged cord or plug, if the product malfunctions or is dropped or damaged in any manner. (see warranty)

11. Avoid contact with moving fan parts.

12. The use of attachments not recommended by the manufacturer may be hazardous.

13. Place the fan on a dry level surface.

14. Do not hang or mount fan on a wall or ceiling.

15. Do not operate if the fan housing is removed or damaged.

16. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

WARNING: To Reduce The Risk of Fire or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.

STAND FAN ASSEMBLY INSTRUCTIONS

• Insert the long Metal Pole into the Base and tighten it by turning either the Pole or the Base (Fig. 1).

• Insert and tighten the short Metal Pole into the Base/Pole Assembly (Fig.1).

• Place the Motor Assembly into the shorter

Fig. 1 Fig. 2

Fan Pole and tighten by turning the Motor Assembly clockwise (Fig. 2). Go to grille assembly instructions.

This fan can be converted into two heights by selecting different size poles to assemble.

1. Stand fan = use both short and long pole

2. Table fan = use only short pole

ASSEMBLY INSTRUCTIONS

BLADE KNOB

REAR GRILLE

BASE

FAN BLADE

REAR GRILLE MOUNTING NUT

FRONT GRILLE

GRILLE HUB

CLIPS

MOTOR

HOUSING

SHORT

METAL POLE

LONG

METAL POLE

GRILLE ASSEMBLY INSTRUCTIONS

• Remove the Rear Grille Mounting Nut from the Motor. Place the Rear Grille onto the Motor Housing, making sure the three holes of the Rear Grille fit over the three matching prongs on the Motor Housing. Tighten the Rear Grille Mounting Nut CLOCKWISE (Fig. 4).

Fig. 5

BLADE KNOB

MOTOR

ASSEMBLY

Fig. 6

• Raise the built in caps around the front grille fasten the caps onto rear grille (Fig.7).

• To change the tilt angle of the fan, simply tilt the Motor Assembly to the angle desired.

NOTE: This will only work when fan is fully assembled

• Push the Fan Blade onto the Motor Shaft, lining up the center of the blade with the D-shape on the Motor Shaft. Tighten the Blade Knob by turning it COUNTER CLOCKWISE (Fig. 5).

• Align the front grille and hook the top grille clip onto the rear grille (Fig. 6).

Fig. 4

MOUNTING NUT

REAR GRILLE

Fig. 7

TABLE FAN ASSEMBLY INSTRUCTIONS

• Insert the short Metal Pole into the Base and tighten it by turning either the Pole or the Base (Fig. 1).

• Place the Motor Assembly into the short Fan Pole and tighten (Fig.2) by turning the

Motor Assembly Clockwise (Fig. 3).

• Go to grille assembly instructions

Fig. 3

MOTOR

ASSEMBLY

SHORT POLE

BASE

OPERATION

• Place your fan on a level and dry surface.

• Plug the power cord into a 120 volt wall outlet.

• To operate the Child Resistant switch, push in and turn the Speed Control Knob (Fig. 8).

• To stop the oscillating feature, pull up hard on the Oscillation Control Knob. You will feel two clicks before oscillation stops (Fig. 9).

• To re-start oscillation push down on oscillation knob.

USING YOUR FAN AS AN AIR CIRCULATOR

• Turn the Speed Control Knob to OFF.

• Tilt the fan motor assembly back so that the front grille of the fan is facing the ceiling.

•

DO NOT USE OSCILLATION FEATURE IN THE AIR CIRCULATOR POSITION.

• Turn the Speed Control Knob to your desired speed.

CLEANING AND STORAGE

• Turn the fan to the OFF position and unplug the fan before cleaning.

• Remove the Front Grille.

• Unscrew the

Blade Knob by turning it CLOCKWISE.

• Pull the Fan Blade away from the Motor Housing.

• Clean the Fan Blade

and grilles with a soft, damp cloth.

• DO NOT immerse the fan in water and never allow water to enter the Motor Housing.

• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.

• To store, disassemble and clean the fan carefully as instructed and store it in its original box. You may leave the fan assembled and covered to protect it from dust. Store the fan in a cool, dry place.

Fig. 8 Fig. 9

PUSH IN AND TURN

OSCILLATION

CONTROL KNOB

CONSUMER RELATIONS/REPLACEMENT PARTS

To speak with a customer service representative or place an order please call our consumer relations center, toll free at 1-800-332-1110. Orders may be placed 24 hours a day, seven days a week with Master Card, Visa or Discover.

To order by mail, Please include $4.50 US/$6.10 CAN for shipping and handling and make check or money order payable to Honeywell Consumer Products Business. Massachusetts residents add 5% sales tax, Canadian residents add 7% GST plus applicable provincial sales tax. Mail to:

Consumer Relations Honeywell Consumer Products Business 250 Turnpike Rd. Southborough MA 01772 USA

NOTE: Honeywell can not ship to P.O. boxes.

Thank you for purchasing a Honeywell fan. For more information about Honeywell visit us at www.honeywell.com

Please specify fan colour and model number.

Item HS-122 Part # Price US Price CAN

Front & Rear Grille HS-122-1 $8.00 $11.75 Rear Grille HS-122-2 $3.00 $4.50

Mounting Nut Fan Blade HS-122-4 $10.00 $14.70 Blade Knob HS-122-5 $3.00 $4.50 Base HS-122-10 $10.00 $14.70 Metal Pole-Short HS-122-11 $5.00 $7.40 Metal Pole- Long HS-122-12 $5.00 $7.40 Motor Assembly HS-122-13 $12.00 $17.70

5 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

The enclosed Customer Response card should be filled out and returned within 7 days of purchase.

. This 5 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

HONEYWELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Honeywell will repair or replace this product if it is found to be defective in material or workmanship. Defective product should be returned to the place of purchase in accordance with store policy. Thereafter, while within the warranty period defective product may be returned to Honeywell.

C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

D. Return defective product to Honeywell Consumer Products with a brief description of the problem. Include proof of purchase and a $14.70 CAN./$10 US check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. Send to:

Honeywell Attn: Returns Department 4755 Southpoint Drive Memphis, TN 38118 USA

+ 14 hidden pages