KAZ HFS-641PC User Manual

OWNER'S MANUAL

SPEED

TIMER

BREEZE

SPEED

TIMER

OFF

BREEZE

ON/SPEED

TIMER

OFF

16" REMOTE CONTROL STAND FAN

Model HFS-641PC

The Honeywell trademark is used by Kaz, Inc. under license from Honeywell Intellectual Properties, Inc.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS FAN

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Use this fan only as described in this manual. Other use not recommended

may cause fire, electric shock or injury to persons.

2. This product is intended for household use ONLY and not for commercial,

industrial or outdoor use.

3. To protect against electric shock, do not place fan in window, immerse unit,

plug or cord in water or spray with liquids.

4. This fan requires a grounded 120 volt power source (3 prong receptacles).

Never connect this fan to any power source other than a properly grounded 120 volt AC receptacle. Do not attempt to defeat this safety feature.

5. Close supervision is necessary when any appliance is used by or near children.

6. Turn the fan to the OFF position and unplug the fan from the outlet when not in

use, when moving the fan from one location to another and before cleaning.

7. To disconnect the fan, first turn control to the OFF position, grip the plug and

pull it from the wall outlet. Never pull by the cord.

8. Do not operate the fan in the presence of explosive and/or flammable fumes.

9. Do not place the fan or any parts near an open flame, cooking or other

heating appliance.

10. Do not operate the fan with a damaged cord or plug or if the product

malfunctions, is dropped or damaged in any manner (see warranty).

11. Avoid contact with moving fan parts.

12. The use of attachments not recommended by the manufacturer may be

hazardous.

13. Place the fan on a dry level surface.

14. Do not hang or mount fan on a wall or ceiling.

15. Do not operate if the fan housing is removed or damaged.

16. A loose fit between the AC outlet (receptacle) and plug may cause

overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

17. Do not press or adjust the front or rear grille while the fan is plugged in

and/or operating.

WARNING: To Reduce The Risk of Fire or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.

ASSEMBLY INSTRUCTIONS

CLIPS (G)

GRILLE HUB

BLADE KNOB (F)

FRONT GRILLE

FAN BLADE

REAR GRILLE MOUNTING NUT (D)

REMOTE CONTROL

REAR GRILLE (E)

SPEED

TIMER

BREEZE

TIMER

SPEED

OFF

BREEZE

SPEED

TIMER

OFF

METAL POLE (C)

CONTROL PANEL

BASE

• Insert the Metal Pole (C) into the Base by lining up the recessed slot in the Pole to the raised dot on the inside of Base and push in (Fig. 1). Be sure that the Pole is fully seated. Hold the Base firmly and twist the Pole CLOCKWISE until it stops. DO NOT OVER-TIGHTEN

ATTACHING THE CONTROL PANEL

• Assemble the Control Panel to the Metal Pole by lining up the three (3) tabs of the Metal Pole with the three (3) indented slots of the Control Panel. Push the pieces together and rotate until they are secure (Fig. 4). Tighten the knob on the back of the Control Panel to lock in place.

• Insert the two (2) AAA batteries into the remote control and slide it into the neck of the Control Panel.

COMPLETING THE ASSEMBLY

MOTOR HOUSING

Fig. 1

RECESSED SLOT

Fig. 2

METAL

POLE

T I M

E R

4 2

T I M

O N

/ S P E

O F

S PE E

L M

B R

E E Z E

E R

E D

CONTROL PANEL

TAB

• Remove the Rear Grille Mounting Nut (D). Place the Rear Grille (E) onto the Motor Housing by making sure the three (3) holes of the Rear Grille fit over the three (3) bumps on the Motor Housing. Tighten the Rear Grille Mounting Nut CLOCKWISE (Fig. 3).

Fig. 3

• Push the Fan Blade onto the Motor Shaft, lining up the blade with the D-shape on the Motor Shaft’s end. Tighten the Blade Knob (F) by turning it COUNTERCLOCKWISE (Fig. 4).

• Properly align the Front Grille and hook the top Grille clip (G) onto the Rear Grille (Fig. 5).

• Fasten the built in clips around the Front Grille onto the Rear Grille (Fig. 6).

NOTE: The tilt angle of the Motor Assembly can be changed by simply tilting the Motor up or down once the fan is completely assembled.

Fig. 4 Fig. 5

Fig. 6

OPERATION

• Place your fan on a level and dry surface.

• Plug the power cord into a 120 Volt AC wall outlet.

• To turn fan on press the “ON/SPEED” button one time.

• When fan is on it will start in low speed. Press button again while on low speed and fan will switch to medium speed. While on medium press “ON/SPEED” button and fan will switch to high speed.

• When your fan is on high speed, pressing the “ON/SPEED” button will return your fan to low speed.

• You will see a red light illuminated on the control panel of the fan showing you what speed your fan is on (Fig. 7).

• To stop the oscillation feature, pull up hard on the Oscillation Control Knob until you feel two clicks. To restart oscillation feature press button down (Fig. 8).

• Tilt the fan head to desired angle.

• To turn the fan off press the “OFF” button.

NOTE: Once your fan is off, the next time you turn it on it will automatically default to the last used speed setting. You can then adjust the speed as desired.

Fig. 7

Fig. 8

illuminated

ON/SPEED

TIMER

for “LOW “ speed

BREEZE

ON/SPEED

TIMER

OFF

OSCILLATION CONTROL KNOB

FEATURES

Breeze: To activate the breeze feature, press the “BREEZE” button once on your

remote control or on the control panel on the fan. Your fan will now speed up and slow down to simulate outdoor air-flow. This feature can be used when your fan is on any speed setting. While using the fan in “BREEZE” mode, if you want to return to standard fan speed operation, press the “BREEZE” button once. Your fan will no longer cycle through its outdoor wind function.

Timer: You can set your fan to conveniently turn itself off within two, four or eight hours.

• This feature operates similar to the speed setting function. To use this feature press the “TIMER” button.

• The time you have set will be displayed by the illuminated green light on the fan control panel.

From Any Speed Setting:

1 press = 2 hours - light glows under 2 2 press = 4 hours - light glows under 4 3 press = 8 hours - light glows under 8

NOTE: If you shut off your fan in “Breeze” mode, the next time you turn your fan on it will be in “Breeze” Mode. If your fan shuts itself off as a result of “Timer” mode running out, the next time you turn your fan on it will default to the last used speed setting.

Feature Combination

• You can use “BREEZE” mode and “TIMER” mode at the same time!

• If you enjoy the soothing effects of “BREEZE” mode, but don’t want to leave your fan running all night, from any speed setting simply select “BREEZE” then choose either 2, 4 or 8 hour time setting by pressing the “TIMER” button.

• At the end of your time setting, the fan automatically turns itself off!

REMOTE

The remote control can be used up to 26 feet (8M) away from the fan. Be sure to point remote directly at the front of the fan to ensure a proper response.

• To remove remote from the fan, slide it up and lift it off the

BREEZE

ON/SPEED

TIMER

uses 2 AAA

OFF

batteries (included)

front panel. To place remote back on the fan, slide it down the track around the fan’s control panel and press gently to snap in place.

• The button on the remote will respond in the same manner as the buttons on the fan. To review these features see “operation” and “features” portion of the owners manual.

• You will hear a “beep” from the fan and see illuminated lights on the fan control panel while using the remote. This shows you that the remote is working.

CLEANING AND STORAGE

• Turn the fan to the off position and unplug the fan before cleaning.

• Use only a soft, damp cloth to gently wipe the fan clean.

• DO NOT immerse the fan in water and never allow water to drip into the motor housing.

• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.

REMOVAL OF THE FRONT GRILLE FOR CLEANING

• Release the Front Grille clips from around the Rear Grille and remove the Front Grille.

• Unscrew the Blade Knob by turning it CLOCKWISE.

• Pull the Fan Blade away from the Motor Housing.

• Gently wipe the Fan Blade and Grilles.

• Re-assemble the fan by following the ASSEMBLY INSTRUCTIONS.

TO STORE YOUR FAN

Store your fan covered in a cool, dry place.

TROUBLE SHOOTING GUIDE

Q: How do I turn the fan on A: To turn the fan on press the “ON/SPEED” button. Press once for low

operation, twice for medium, three times for high.

Q: My fan is slowing down and speeding up, is there something wrong A: No, you have the fan set to “Breeze”. To turn this feature off press the

“BREEZE” button once. The fan should now operate normally. Q: What happens if I have two of the same model Honeywell®Remote Control

fans and two remotes A: If both fans are the same model Honeywell®Remote Control Stand Fans, then both remotes should work on either fan.

CONSUMER RELATIONS / REPLACEMENT PARTS

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE RETURN THE FAN TO THE ORIGINAL PLACE OF PURCHASE OR SEE YOUR WARRANTY. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF. DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE FAN OR PERSONAL INJURY.

IF YOU HAVE ANY QUESTIONS REGARDING THIS FAN, PLEASE CALL OR WRITE:

Kaz Home Environment Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772

Toll free: 1-800-332-1110 E-mail: consumerrelations@kaz.com

Please visit us at www

.kaz.com

5 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product. A.This 5 year limited warranty applies to repair or replacement of product found to be

defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. KAZ IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B.At its option, Kaz will repair or replace this product if it is found to be defective in material

or workmanship. Defective product should be returned to the place of purchase in accordance with store policy. Thereafter, while within the warranty period defective product may be returned to Kaz.

C.This warranty does not cover damage resulting from any unauthorized attempts to repair or

from any use not in accordance with the instruction manual.

D.Return defective product to Kaz Home Environment with a brief description of the problem.

Include proof of purchase and a $10 US/ $15.50 CAN check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. Send to:

In U.S.:

Kaz Home Environment Attn: Returns Department 4755 Southpoint Drive Memphis, TN 38118 USA

In Canada:

Kaz Home Environment Attn: Returns Department 510 Bronte Street South Milton, ON L9T 2X6 Canada

+ 16 hidden pages