USE AND CARE MANUAL
5 LIGHT CRYSTAL CHANDELIER
A
B
C
H1
Mounting strip
1 pc
H5
Lock washer
1 pc
H9
(Pre-assembled to
Ring
screw collar loop)
1 pc
H13
Thumbscrew
loop assembly (A))
2 pcs
(Pre-assembled to
Hardware
H2
Outlet box screw
2 pcs
H6
Green ground screw
(Pre-assembled to mounting strip)
1 pc
H10
Quick link
2 pcs
H14
Crystal strand "A"
35+1 pcs
(Parts are not to scale)
H3
Threaded tube
1 pc
H7
Wire connector
3 pcs
H11
Canopy
1 pc
H15
Crystal strand "B"
1 pc
D
H4
Hex nut
1 pc
H8
Screw collar loop
1 pc
H12
Chain
1 pc
THIS MANUAL CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
Page 1 of 5
IMPORTANT SAFETY INFORMATION
• Please read and understand this entire manual before attempting to assemble, operate or install the
product.
• Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse
(or switching off circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit
wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which
could cause serious injury or death from electric shock.
• All electrical connections must be in agreement with local codes, ordinances or the national electric
code (NEC). Contact your municipal building department to learn about your local codes, permits and/or
inspections. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or
have your fixture installed by a qualified licensed electrician.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60°C. Consult a qualified
electrician before installation.
• Do not exceed the recommended wattage. Refer to the re-lamping label on the light socket for maximum
wattage.
• Do not replace a bulb when electrical outlet switch is turned to the “ON” position.
• Do not immerse your lamp in water; doing so will damage the wire.
• Keep materials that burn easily away from lighted bulbs.
PREPARATION
• Before beginning assembly, installation or operation of product, make sure all parts are present. Compare
parts with package contents list and diagram on previous page. If any part is missing or damaged, do not
attempt to assemble, install or operate the product. Contact customer service for replacement parts.
• Tools required for assembly (not included): flathead screwdriver, phillips screwdriver, pliers, electrical tape,
wire cutters, safety glasses, ladder, wire stripper.
INSTALLATION
Preparing the mounting strip
1
• Screw the threaded tube (H3) into the mounting
strip (H1), and secure it using the lock washer (H5)
and hex nut (H4).
NOTE: The threaded tube (H3) should extend long
enough to protrude through the canopy, when it
is mounted. (Adjust as needed.)
Installing the mounting strip
2
• Fasten the mounting strip (H1) onto the outlet
box using two outlet box screws (H2).
H1
H3
H5
H4
Page 2 of 5
H1
H2
INSTALLATION (continued)
Attaching the canopy to the
3
outlet box
• Place the canopy (H11) over the threaded tube
(H3), and screw the screw collar loop (H8) onto
the threaded tube (H3).
• Secure the canopy (H11) using the ring (H9).
H3
H11
H8
Assembling the loop and the
4
center column
• Pull the fixture wire through the loop (A) and the
center column (B), and screw the loop (A) and
the center column (B) onto the fixture body (D).
A
B
D
H9
Assembling the shade to the
5
fixture body
• Unscrew the two thumbscrews (H13) from the
center column (B). Place the shade (C) over
the top of the center column (B). Align the two
holes of the shade (C) and the metal plate of
the center column (B), then tighten the two
thumbscrews (H13).
NOTE: Remove the plastic cover from the shade
before using.
B
H13
C
Hanging the crystal strands the
6
fixture body
• Hang the crystal strands "B" (H15) onto the end
of the finial of the fixture body (D).
• Hang the crystal strands "A" (H14) onto the arms
and caps of the fixture body (D) as shown below.
NOTE: Hang the crystal strands "A" (H14) onto the
caps of the fixture body (D), the opening of the
hook must face outwards, otherwise, the crystal
strand will fall easily as shown below.
D
H14
H14
Page 3 of 5
H14
H14
H15
INSTALLATION (continued)
Attaching the chain
7
• Adjust the chain (H12) to the desired height
by spreading the end link of the chain (H12)
apart. Use a pair of pliers and a screwdriver (not
included). Wrap a soft cloth around the pliers to
protect the chain’s finish.
• Open the first quick link (H10), connect chain
(H12) to the loop (A) and close the quick link
(H10).
• Open the second quick link (10), connect other
end of chain (H12) to the screw collar loop (H8)
and close the quick link (H12).
H8
H10
H12
H10
A
Weaving the fixture wire
8
• Unscrew the ring (H9) from the screw collar loop
(H8), and lower the canopy (H11) and ring (H9)
over the chain (H12) on the fixture.
• Weave the fixture wires and bare copper ground
wire up through the chain (H12), ring (H9),
canopy (H11), screw collar loop (H8), threaded
tube (H3), and then into the outlet box.
H3
H8
H12
H11
H9
A
Making the electrical
9
connections
• Strip 3/4 in. of insulation from the wire ends.
• Connect the glossy live wire from the fixture to
the black wire from the outlet box, and the rough
neutral wire from the fixture to the white wire
from the outlet box.
• The bare copper ground wire from the fixture
must loop one turn under the head of the green
ground screw (H6) on the mounting strip (H1)
before it is connected to the ground conductor of
the supply circuit.
• Cover the wires with wire connectors (H7). Tape
the wire connectors (H7) and wires together, and
carefully position all wires inside the outlet box.
NOTE: The glossy live wire has the text printed on it;
the rough neutral wire has the ridge on it.
H7
Installing the canopy to the
10
outlet box
• Raise the canopy (H11) all the way up to the
ceiling, and tighten the ring (H9) onto the screw
collar loop (H8) until the canopy (H11) is firmly
held against the ceiling.
H11
H9
H8
H1
H6
Page 4 of 5
INSTALLATION (continued)
11
NOTE: You can also use five MAX 9W candelabra base (E12) self-ballasted LED bulbs. Do not exceed the
Installing the light bulbs
• Install the light bulbs (not included) into the socket. Use five Max 60W candelabra base (E12) type “B”
bulbs (recommended).
recommended wattage.
CLEANING
• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or
wipe carefully.
• To clean the fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the
fuse box. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.
TROUBLESHOOTING
• The light does not come on at all:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
• Fuse blows or circuit trips when light is turned on.
a) Check for crossed wires, ensure wiring is correct.
Page 5 of 5
Loading...