Kawasaki CD1677 Operating Instructions Manual

1. PRECAUTIONS

Follow the advice below for safe and appropriate operations.

ON PLACEMENT

• Do not use the unit in places which are extremely hot, cold, dusty, or humid.

• Place the unit on a flat and even surface.

• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet.

ON AC VOLTAGE

• Before use, check that the rated voltage of your unit matches your local voltage.

FCC INFORMATION (FOR USA ONLY)

This device complies with Part 15 of FCC Rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operations.

ON SAFETY

• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard.

• When you are not going to use the unit for a long period of time, disconnect the AC power cord.

ON CONDENSATION

• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the CD player.

• When there is condensation inside the unit, the unit may not function normally.

• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.

Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.

2. IMPORTANT SAFETY INSTRUCTIONS

4. PARTS IDENTIFICATION

1 2

4 5

9 10 11

1. CD door

2. ON indicator

3. STANDBY indicator

4. VOLUME control

5. CD OPEN/CLOSE button

6. CD PROGRAM button

7. PHONES jack

8. FUNCTION switch (ST.BY/TAPE/TUNER/CD)

9. CD REPEAT button

10. CD STOP button

11. Remote sensor

12. RADIO dial pointer

13. CD display

14. FM STEREO indicator

5. GENERAL OPERATION

15. TUNING control

16. DISC SKIP button

17. CD SKIP/SEARCH buttons

18. BAND switch (FM/AM)

19. BEAT CUT/FM MODE switch (FM.ST/FM MONO)

20. CD PLAY/PAUSE button

21. Cassette holder

22. Cassette operation controls

REC button

PLAY button

REW button F.FWD button STOP/EJECT button

PAUSE button

10. COMPACT DISC PLAYBACK

1. Set the FUNCTION switch to CD.

12 13

14 15 16 17

19 20

2. Press the OPEN/CLOSE button to open the disc tray. Place the first disc onto the disc holder, with the label side up.

3. Press the DISC SKIP button to revolve the tray clockwise. Place other disc(s) on the disc holder(s).

WARNING: Take out all discs from the disc tray before transportation.

4. Press the OPEN/CLOSE button to close the disc tray. It takes a short while for your player to check the discs.

5. Press the DISC SKIP button to select the desired disc. Press either one of the SKIP/SEARCH buttons to select the desired track.

6. Press PLAY/PAUSE button to start playback.

FUNCTION

ST.BY

TAPE

CD TUNER

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet , consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinch particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)

Only use attachments/accessories specified by the manufacturer.

12)

Unplug this apparatus during lightening storms or when unused for long periods of time.

13)

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14)

This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases shall be placed on the apparatus.

3. SYSTEM CONNECTIONS

SPEAKERS CONNECTING

• Connect the wires to the speaker terminals in correct position.

• Connecting speakers other than the speakers supplied with the unit may damage the unit.

AC POWER CONNECTING

• Before use, check that the rated voltage of your unit matches your local voltage. Make sure speakers are connected correctly before plugging the AC power cord into an AC outlet.

CAUTION :

• Be sure the AC power cord is disconnected and all functions are off before making connections.

6. COMPACT DISC (CD) DISPLAY

1. REPEAT mode indicators

2. PROGRAM indicator

3. Playback indicator

4. Pause indicator

5. Disc indicator

6.Track indicator

7. SOUND ADJUSTMENT

TO ADJUST THE VOLUME

Adjust the VOLUME to the desired listening level.

FOR PERSONAL LISTENING

Connect headphones ( Ø3.5mm stereo mini plug) to the PHONES jack. Adjust the VOLUME to the desired listening level. When headphones are connected, the speakers are automatically disconnected.

WHEN RECORDING

The VOLUME control may be adjusted with no effect on the recorded signal.

8. RADIO OPERATION

1. Set the FUNCTION switch to TUNER.

FUNCTION

ST.BY

TAPE

CD TUNER

3. Tune into a station.

2. Select the desired band.

4. Adjust the volume.

To stop playing:

a) For a moment only, press PLAY / PAUSE button and " " will be

displayed. Press this button again to resume playing.

b) Press CD STOP button.

NOTE:

• To locate a track of currently selected disc, press or SKIP/SEARCH button repeatedly.

• To locate a track of another disc, press DISC SKIP button to get to desired disc first and then press or SKIP/ SEARCH button repeatedly.

• To search a track, keep or SKIP/SEARCH button pressed and release it at desired point.

FORWARD

SKIP

REVERSE

SKIP

PRESS IT REPEATEDLY KEEP IT PRESSED

REVERSE

FORWARD

11. CD REPEAT PLAYBACK

REPEAT PLAYBACK - DURING PLAYBACK MODE

To repeat the current track

• Press REPEAT button until REPEAT ONE appears on the CD display and the currently playing track will be played repeatedly until the stop button is pressed.

• Press or SKIP/SEARCH button with repeat function on, repeat can still skip through different tracks of the currently selected disc.

To repeat the whole disc

• By pressing the REPEAT button until REPEAT ONE DISC appears on the CD display, the current disc will be played repeatedly starting from the currently playing point.

• By pressing or SKIP/SEARCH button with REPEAT-ONE-DISC function on, one can still search through the whole disc, and the player will start playing from the selected point.

To repeat all discs

• Press REPEAT button until REPEAT ALL DISC appears on the CD display.

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT (FOR USA AND CANADA ONLY).

FM ANTENNA

• Do not connect to an outside antenna.

9. RADIO OPERATION

FOR BETTER RECEPTION

Fully unwind the wire antenna. Then extend the wire antenna and place it in the position that sounds best.

NOTE:

Do not connect FM antenna wire to outside antenna.

TO RECEIVE THE FM BROADCAST IN STEREO

Set the Mode switch to FM.ST. When the FM STEREO broadcast is received, FM STEREO indicator lights up.

IF THE FM BROADCAST SIGNAL IS WEAK

Set the Mode switch to FM MONO position to turn off the FM STEREO indicator and background noises become monaural.

AFTER LISTENING

Set the FUNCTION switch to ST.BY (Standby).

AM / MW Rotate the unit to get the best

receiving position.

• By pressing on or SKIP/SEARCH button will make the player start playing from the newly selected point of the currently playing disc.

• By pressing on DISC SKIP button will make the player start playing from the first track of the newly selected disc. The or SKIP/SEARCH button can be used to choose a particular track on this selected disc, the player will then start playing from that point.

To cancel repeat play

• Press REPEAT button until the word 'REPEAT' disappears on the CD display.

ATTENTION - If the CD player does not operate properly

1. Slide the FUNCTION switch from CD to ST.BY (Standby).

FUNCTION

ST.BY

TAPE

CD TUNER

2. Slide the FUNCTION switch from ST.BY to CD.

FUNCTION

ST.BY

TAPE

CD TUNER

12. CD PROGRAMMED PLAYBACK

A program of up to 32 tracks from all the available discs in the disc tray can be played in a preset order.

1. Press the PROGRAM button (in stop mode).First " P01 " will display for about 2 seconds and then Disc Number (example 5d) will flash on the display. "P01" means you are setting the first programmed track.

PROGRAM

2. Press the DISC SKIP button to select the desired disc. (example 5d)

3. Press the / SKIP/SEARCH buttons to select the desired track. (example the first track of Disc 5)

4. Press the PROGRAM button again to store this track in memory.

PROGRAM

5. To add additional tracks, repeat steps 2 to 4.

6. To start playback, press the PLAY/PAUSE button.

PROGRAM

14. RECORDING FROM BUILT-IN TUNER

USE ONLY NORMAL (TYPE I) TAPE FOR RECORDING

1. Set the FUNCTION switch to TUNER and tune to your desired

2. Insert a tape into the cassette holder.

station.

FUNCTION

ST.BY

TAPE

CD TUNER

The side you want to

be recorded.

3. Press the RECORD button which also engages the PLAY button.

• If whistle is heard (beat) it may be reduced by switching the "Beat Cut" to the other position.

15. RECORDING FROM CD PLAYER

USE ONLY NORMAL (TYPE I) TAPE FOR RECORDING

1. Set the FUNCTION switch to CD.

FUNCTION

ST.BY

TAPE

CD TUNER

3. Press the RECORD button

which also engages the PLAY button.

2. Insert a tape into the cassette holder.

The side you

want to be

recorded.

4. Press the

PLAY/PAUSE

button of the CD player.

5CD CHANGER

HOME STEREO SYSTEM

OPERATING INSTRUCTIONS

WARNING

EXPLANATION OF GRAPHICAL SYMBOLS:

CAUTION

RISK OF ELECTRIC

SHOCK DONOT OPEN

"CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL."

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute an electric shock to persons.

The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

To check the program

After setting , press PLAY/PAUSE button to start paly, then press

or button to check programmed tracks. The Disc No. and

track No. will appear on the dispaly.

To stop programmed play for a moment:

• Press the PLAY/PAUSE button and " " will be displayed. Press this button again to resume playing.

PROGRAM

To add additional tracks during program playback:

1. Press STOP button first, the current playing disc No. will appear

on the display.

2. Press PROGRAM button, the first programmed No. and the track

No. will appear on the display.

PROGRAM

3. Press DISC SKIP or / SKIP/SEARCH buttons to select additional tracks.

To erase the whole program,do one of the following:

• Press STOP button twice to erase the program.

• Set the FUNCTION switch to other functions.

• Open the disc tray by pressing the OPEN/CLOSE button.

FUNCTION

ST.BY

TAPE

CD TUNER

NOTE:

• The same track can be selected more than once in the same program.

• With program on, the / skip function is available only for the selected tracks.

• With program on, repeat play cannot be done for ALL DISCS.

13. TAPE PLAYBACK

1. Set the FUNCTION switch to TAPE.

FUNCTION

ST.BY

TAPE

CD TUNER

3. Insert a cassette tape into the cassette compartment.

TO STOP PLAYBACK

Press the STOP / EJECT button.

TO INTERRUPT PLAYBACK

Press the PAUSE button. To resume playing, press the PAUSE button again.

TO REWIND AND FASTWIND

Press the

REW or F.FWD button. Press the STOP /

EJECT button to stop winding at the desired position.

WHEN THE TAPE REACHES ITS END

During fast wind or normal play, the tape will stop automatically when its end is reached.

2. Press the STOP / EJECT button.

4. Press the PLAY button to begin playback.

TO STOP RECORDING

Press the STOP / EJECT button.

TO INTERRUPT RECORDING

Press the PAUSE button. To resume recording, press the

PAUSE button again.

TO ERASE A RECORDED TAPE

1) Set the FUNCTION button to TAPE.

2) Insert a tape with the side you want to erase facing you.

3) Press the RECORD button to start erasing.

16. REMOTE CONTROL

1. - SKIP(SEARCH) Button

2. REPEAT Button

3. +SKIP(SEARCH) Button

4. DISC SKIP button

5. PLAY/PAUSE Button

6. STOP Button

USING THE REMOTE CONTROL CORRECTLY

• Point the Remote Control at the REMOTE SENSOR located on the unit.

• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded, causing unreliable operation.

• The recommended effective distance for remote operation is about 4 meters (13 feet).

TO CHANGE THE REMOTE CONTROL BATTERY

1. Open the battery

door.

2. Insert one CR2025 (3V) size battery.

ATTENTION

Take out the PVC sheet before operating the Remote Control.

BATTERY REPLACEMENT

When battery becomes weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the battery.

NOTE:

If the Remote Control is not to be used for a long time, remove the battery to avoid damage caused by battery leakage corrosion.

WARNING:

Do not dispose of batteries in fire, batteries may explode or leak.

17. MAINTENANCE

CLEANING CD

If the CD skips or will not play, the disc may need to be cleaned. Before playing, wipe the disc from the center out with a cleaning cloth. After playing, store the disc in its case.

CLEANING THE TAPE HEADS

To maintain optimum sound quality, clean the playback/record heads (a), erasure head (b), pinch roller (c), and capstans (d) regularly (every 10 hours of use). Use a cotton swab lightly moistened with cleaning fluid or denatured alcohol.

CLEANING THE UNIT

Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.

If an abnormal display indication or an operating problem occurs, disconnect the AC power cord. Wait at least 5 seconds, then reconnect it. Before transporting the unit, take out all discs from the CD tray.

IMPORTANT NOTE:

INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCK

DEFEATED.

AVOID EXPOSURE TO BEAM

This product contains a low power laser device.

CLASS 1 LASER PRODUCT

CLASS 1 LASER

PRODUCT

18. TROUBLE SHOOTING GUIDE

CAUTION

The following checks will assist in the correction of most problems which you may encounter with your system.

SYMPTOM

GENERAL

No sound.

No sound from one channel or unbalanced left and right volume.

Reversed left and right sound.

Lack of bass sound or apparently imprecise physical location of musical instruments.

Severe hum or noise.

RADIO RECEPTION

The FM STEREO indicator flashes.

Severe hum or noise.

CD PLAYER OPERATION

Play does not start.

Distorted playback or sound loss during CD playback.

CASSETTE DECK OPERATION

Recording cannot be made.

Recording or playback cannot be made or there is a decrease in sound level.

Excessive wow or flutter, or sound dropout.

Insufficient erasure.

Increase of noise or erase of high frequencies.

CAUSE (AND REMEDY)

• Turn VOLUME clockwise.

• The headphones are connected. Disconnect them.

• Check the speaker connections of the inoperative channel.

• Check the speaker cord connection and speaker location.

• Check the speaker connection for proper phasing.

• The TV or VCR is too close to the s tereo system. Separate the stereo system from the TV or VCR.

• Unwind the antenna wire.

• The disc is not placed correctly.

• Dirty disc.

• The disc is inserted upside down.

• The player is in the pause mode.

• Moisture condensation.

• CD is dirty or scratched.

• No cassette in the cassette holder.

• The tab is removed from the tape.

• The tape is wound completely.

• Dirty head.

• Magnetic build-up on the record/ playback head.

• Contamination of the capstans or pinch rollers.

• Magnetic build-up on the erase head.

19. SPECIFICATIONS

Power requirements AC ~ 120V 60Hz (USA/CANADA)

Power consumption 15 W

Specifications and external appearance are subject to change without advance notice due to continuous product improvement.

Printed in China

AC ~ 220V 50Hz (other countries) AC ~ 230-240V 50Hz (Europe) AC ~ 240V 50Hz (Australia) AC ~ 110-120V/220-240V 50/60Hz (other countries)

811-167791-030

Kawasaki CD1677 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual