Kawasaki 840121 User Manual

MODEL

#840121

2.2 GALLON WET/DRY
VACUUM/BLOWER

INSTRUCTION MANUAL

FOR CUSTOMER SERVICE

POUR LE SERVICE APRÉS VENTE

OU DU CONSOMMATEUR

PARA EL SERVICIO

PARA EL CONSUMIDOR

1-800-590-3723

Printed in China

KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:

©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA

840121 – 2.2 Gallon Corded Wet/Dry Vacuum/Blower_Rev 9/28/06

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: [e-mail].
YOUR FEEDBACK IS VITAL TO US.

87-1904-60957

CONGRATULATIONS!

Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please
contact us at 1-800-590-3723. Properly cared for, this tool will give you many
years of satisfaction.

INTENDED USE

This tool is intended for consumer use only.

GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to

follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.

Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.

This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.

DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.

WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.

TABLE OF CONTENTS

CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION ONE

GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS . . . . 2

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3

IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

ELECTRICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SECTION TWO

SAFETY RULES FOR WET/ DRY VACUUM / BLOWERS . . . . . . . . . . . . . 5

VACUUM SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

BLOWING SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

EXTENSION CORD USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SECTION THREE

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

OPERATING THE WET / DRY VACUUM / BLOWER . . . . . . . . . . . . . . . . . 9-11

DRY VACUUMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

WET VACUUMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

EMPTYING THE DUST CONTAINER . . . . . . . . . . . . . . . . . . . . . . . . 10

BLOWER USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

SECTION FOUR

MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS . . . . . . . . . . . . . . 14

SECTION FIVE

3 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18

1 2

ELECTRICAL SAFETY

Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates the need for the three wire

grounded power cord and grounded power supply system.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is

grounded.

Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tool or pull the plug
from an outlet. Keep the cord away from heat, oil, sharp edges, or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk

of electric shock.

When operating the tool outside, use an outdoor extension cord marked “W­A” or “W.”These cords are rated for outdoor use and reduce the risk of elec-

tric shock.

SERVICE

Tool service must be performed only by qualified repair personnel. Service or

maintenance by unqualified personnel may result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instructions may create a risk of shock or injury.

4

CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.

CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.

NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.

IMPORTANT SAFEGUARDS

People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.

WARNING: Some dust created by power sanding, sawing, grinding, drilling and

other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.

WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.

Wash hands after handling.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

3

NEVER vacuum up smoldering cigarette butts, hot ashes or any other burning mate­rial. This may cause the unit to burst into flame.

NEVER use the vacuum if the filter is wet or missing.

BLOWING SAFETY

DO NOT use Wet/Dry Vacuum/Blower as a sprayer.
DO NOT point the nozzle or exhaust vents toward your eyes, ears or hair. DO NOT

point nozzle at bystanders or animals. Keep air discharge directed at the work area.
Keep children away while blower is in use.
USE ONLY for dust, dirt, leaves and other light debris. This product should not be

used for heavy-duty blowing.

If you have a pacemaker, consult your doctor before

using this product. This equipment could cause pacemaker interference or fail-

ure when used at close quarters.

GROUNDING INSTRUCTIONS

The electrical power source for this Wet/Dry Vacuum/Blower MUST be grounded in
order prevent possible electric shock or even death should the tool malfunction or
breakdown. Grounding provides a path of least resistance for electric current thus
reducing the risk of electrical shock. The power source must also use a minimum
20A service and not used if other power tools on the same circuit are in use.

This Wet/Dry Vacuum/Blower is equipped with a grounded 3-wire power cord with
a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter
can be used as long as it is connected to the center screw in the wall plate. Never
modify the electrical plug by cutting off the grounding prong so it will fit into unap­proved, un-grounded electrical receptacles.

SAFETY RULES FOR WET / DRY VACUUM / BLOWERS

Never immerse the motor housing in water or liquid. Do not expose to rain
or other wet conditions. Failure to keep motor housing dry will lead to risk of

electric shock.

Never handle the Wet/Dry Vacuum/Blower with wet hands.

Keep body away from grounded surfaces like refrigerators, pipes or ranges.

For additional protection against shock, connect the Wet/Dry Vacuum/Blower
to an outlet with a Ground Fault Circuit Interrupter (GFCI).

Keep the ventilation openings clear of dust, hair, paper or anything else that
may restrict air flow.

NEVER run the Wet/Dry Vacuum/Blower over the cord.

DO NOT vacuum toxic materials.

STOP using the Wet/Dry Vacuum/Blower immediately if the motor housing
breaks and the motor or any other electrical components are exposed. Using

the Wet/Dry Vacuum/Blower in this condition could lead to shock or serious
personal injury.

Always wear safety goggles or eye protection when using this tool. Operation
of the Wet/Dry Vacuum/Blower can result in foreign objects being blown into
the eyes resulting in severe eye damage. NOTE: Everyday glasses are not SAFE­TY GLASSES and not compliant with ANSI.

Use a dust mask or respirator for applications which generate dust.

Always wear an OSHA approved dusk mask or respirator when inside the
work area. Replace the filter daily. NOTE: Not all dust masks offer protection

from lead paint dust. Be sure to use the proper mask for the job.

Wear ear protection when using the Wet/Dry Vacuum/Blower for extended
hours or when using it in a noisy area.

Maintain labels and nameplates on the Vacuum/Blower. These carry impor-

tant information. If unreadable or missing, contact Alltrade for a replacement.

VACUUM SAFETY

NEVER leave Wet/Dry Vacuum/Blower running unattended.
NEVER vacuum in the presence of flammable or explosive materials such as gasoline,

natural gas, coal dust, magnesium dust, gun powder, hydrogen, solvents or lighter
fluid. Sparks inside the motor can cause flammable dust, liquid or gases to explode.

DO NOT vacuum toxic materials.
DO NOT use for grooming animals.

5

UNGROUNDED AC RECEPTACLE

GROUNDED RECEPTACLE

GROUNDING ADAPTER

WET/DRY VACUUM/BLOWER
POWER CORD

WET/DRY VACUUM/BLOWER
POWER CORD

COVERPLATE

MOUNTING SCREW

FUNCTIONAL DESCRIPTION

CONTROLS AND COMPONENTS:

1. ON/OFF Switch

2. Hose with Swivel Ends

3. Nozzle

4. Vacuum Port

5. Blower Port

6. Power Cord

7. Cord Storage Indentation

COMPONENT MODEL NUMBER

BARE VACUUM CLEANER 691252
FILTER 691286
NOZZLE 691285
HOSE 691284

8

If you have questions about hooking up the Wet/Dry Vacuum/Blower, contact a
certified electrical contractor to install the proper circuitry acceptable for this and
other power tools you use. Repair or replace any damaged electrical wiring

IMMEDIATELY.

EXTENSION CORD USAGE

Extension cords are not recommended for use with this Wet/Dry Vacuum/Blower.
Extension cords, if used, must be properly grounded with a 3-prong plug on one
and a 3-hole receptacle on the other. DO NOT use grounding adapters with an
extension cord. Extension cords must be UL listed and use a minimum of 18
A.W.G. wiring. Extension cords should never exceed 25 feet in length. Extension
cords, that are too long, cause a voltage drop over the extra distance causing the
Wet/Dry Vacuum/Blower motor to run slower with the possibility of causing dam­age to the motor. Using extension cords with smaller than the recommended wire
gauge run the risk of getting too hot, melting, and/or causing fires. See table,

“Extension Cord Specifications”, on page 13.

SYMBOLS

IMPORTANT: Some of the following symbols may be used on your tool. Please

study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.

SYMBOL NAME EXPLANATION

V Volts Voltage (Potential)
A Amperes Current

Hz Hertz Frequency (Cycles per Second)

W Watt Power

Kg Kilograms Weight

Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation

min Minutes Time

s Seconds Time

! Diameter Size of Drill Bits,

Grinding Wheels, etc.

No load speed No-load Rotational Speed

.../min Revolutions per Minute Revolutions, Surface Speed,

Strokes, etc. per Minute

1,2,3, … Ring Selector Settings Speed, Torque or Position Settings

4

13

3

10

7

5

6

1

11

12

2

9

8

8. Latches

9. Dust Container

10. Filter Bag

11. Rubber Band

12. Filter Cage

13. Ball Float (Inside Filter Cage)

WET VACUUMING

• Remove motor housing by pulling out on the latch­es located on either side of the dust container.

• Remove the filter bag.

• Place motor housing on top of the dust container
and press down until the latches pop into place.

• Insert hose into the vacuum port.

• Plug in power cord and switch power to ON.

When the dust container is full of liquid, the float ball
will rise to the top and automatically shut off the air
flow. The sound of the motor will become more high
pitched as the suction ceases and the motor works
harder. When this happens, dry off your hands and
feet and shut off the motor immediately. LEAVING

THE MOTOR RUNNING WHEN THE BALL IS IN THE
RAISED POSITION CAN DAMAGE THE WET/DRY
VACUUM/BLOWER.

Empty dust container before continuing.

EMPTYING THE DUST CONTAINER

Always unplug the power cord before emptying the dust

container to prevent injuries from accidental starting.

• Remove motor housing by pulling out on the latches located on either side of
the dust container.

• ALWAYS dispose of container contents wisely. Use proper waste receptacles.

• Clean out dust container thoroughly.

• Replace filter bag.

• Snap motor housing back onto dust container.

BLOWER USE

ALWAYS wear ANSI-approved safety glasses when using

blower. Particles may fly up into eyes and cause permanent damage. Wear

hearing protection if using blower for extended periods. Dust masks are also
recommended when blowing fine material.

OPERATING THE WET/DRY VACUUM/BLOWER

Do not operate the Wet/Dry Vacuum/Blower in areas where flammable gases
or explosive dust are present. This will reduce the risk of fire or explosion.

Do not vacuum flammable or combustible liquids or hot ashes.

To reduce the health hazards from vapors or dust, DO NOT vacuum toxic
materials.

DRY VACUUMING

• Remove motor housing by pulling out on the
latches located on either side of the dust
container.

• Make sure the filter bag is dry. A wet filter
bag will clog if used to vacuum dry material.

• Check that the filter bag is firmly attached to
the filter basket. Make sure the rubber band
is as close to the cover as possible. Gaps will
allow vacuumed material to blow back out
through the blower hole.

• Place motor housing on top of the dust
container and press down until the
latches pop into place.

9

• Insert hose into the vacuum port.

• Plug in power cord and switch
power to ON.

• When vacuuming large amounts
of debris or very fine dust, empty
the dust container and filter bag
frequently.

• When vacuuming is completed,
turn the switch OFF and unplug
the power cord.

• Release filter bag by pulling rubber band out
around the black plastic posts.

• Pull filter bag off filter cage. Clean or discard.

• Clean area around the top of the filter cage
where filter bag will be attached. Removing
stray dust particles will ensure a tighter fit.

• Push replacement filter onto filter cage. Make
sure bag reaches all the way to the lid.

• Work your way around the filter bag, carefully
releasing the rubber band. Make sure that the
bag is held securely and that there are no gaps.

STORAGE

ALWAYS empty dust container before storage.

Wrap cord around the indentation at the bottom of
the motor housing.

Attach one end of the hose to the blower port and
the other to the vacuum port.

Store indoors in a closed box or covered with a
cloth.

STORING THE CORD

Store the power cord by wrapping it around the
indentation at the bottom of the motor housing.

ALWAYS fully uncoil power cord before use.

12

• Clean out dust container so blower will
not spray dust into the air when
activated.

• Insert hose into blower port at the rear
of Wet/Dry Vacuum/Blower.

• Plug in power cord and switch power
to ON.

• NEVER point blower hose toward
people or animals.

• Use blower to move dirt, sawdust,
leaves and other small debris away
from patios, garages and driveways.

• When blowing is completed, turn the switch off and unplug the power cord.

MAINTENANCE AND CLEANING

Before each use, make sure dust container is clean and empty. Check filter bag for
holes or tears. Clean or replace if necessary.

Wipe motor housing with mild soap and water. NEVER use solvents or harsh
chemicals.

Use warm water and mild soap to clean dust container thoroughly. Dry with soft
cloth.

DO NOT attempt to service the Wet/Dry Vacuum/Blower yourself. Take the unit to
an authorized repair technician.

CLEANING AND REPLACING FILTER

ALWAYS unplug Wet/Dry Vacuum /Blower before clean-

ing or changing the filter bag.

NEVER remove filter cage. It is there to prevent injury.

Be careful not to tear the bag when changing or cleaning the filter. NEVER use a fil­ter bag with tears or holes in it. Torn bags will release a great deal of dust.

• Remove motor housing by pulling out on the latches located on either side of
the dust container.

• Turn motor housing upside-down and balance on top of dust container.

11

• Keep rubber band as close to the lid as
possible.

• Turn motor housing over and snap back onto
dust container.

SPECIFICATIONS

SPECIFICATIONS

Voltage 120V 60 Hz
Peak Horsepower 1.5
Holding Capacity 2.2 Gallons
Flex Hose Dimensions 1 5/8" Diameter, 56 3/4" Long
Overall Dimensions 11 1/4" W, 14 1/4"L, 14 3/4" H
Weight Approx. 7.0 lbs

OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS

Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.

Cordless Drills/Screwdrivers

Impact Wrenches

Sanders

Jigsaws

Circular Saws

Angle Grinders

Reciprocating Saws

Routers

Rotary Tools

Corded and Cordless Multi-Purpose Tools

Wide Range of Accessories and more

STORING THE HOSE

Attach one end of the hose to the
blower port and the other to the
vacuum port. This will keep the hose
safe and convenient.

ACCESSORIES

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on
another tool.

Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.

If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-

ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on next page).

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS

TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.G

AMPERE 10FT. 25FT. 50FT. 100FT.

3-6 18 18 18 18
6-8 18 18 18 16

8-10 18 18 18 14
10-12 16 16 14 14
12-16 14 12 12 ­16-20 12 12 12 -

13 14

be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi­ble for the return shipping charges. Alltrade’s repair and/or replacement of any non­conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.

Exclusions

This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.

This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.

DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,

3 YEAR LIMITED WARRANTY

Express and Exclusive Limited Warranty to Original Retail Buyer

Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud­ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.

SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any

COMMERCIAL OR RENTAL PURPOSE.

The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.

Warranty Performance

By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will

15 16

Limitation Of Liability

IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.

Limitations on Warranty Disclaimers

Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.

If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.

1817

COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.

Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.

The use of other than genuine Alltrade Repair Parts will void warranty.

Warranty Disclaimers

EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.