Kasco LED8012 Owner's Manual

Owners Manual

LED Fountain Light Kit

Model LED8012

Contents

Important Safety. . . . pg2

General Instructions. . . . pg2

Parts Included. . . . pg2

LED8012 Assembly Instructions. . . . pg2

Additional Color or Replacement Kits. . . . pg4

Maintenance Recommendations. . . . pg4

Warranty Policy. . . . pg5

Replacing 8 Puck Lights. . . . pg6

Troubleshooting Tips. . . . pg6

Customer Repair Form. . . . pg7

Registration Information. . . . pg8

Kasco Marine, Inc.

800 Deere Rd.

Prescott, WI 54021

PH [phone]

FAX [phone]

www.kascomarine.com

Rev. 02/22/13

THANKS
We at Kasco Marine, Inc. would like to both thank
and congratulate you on your purchase of the LED
Light Kit. This kit will illuminate your fountain for a
beautiful display. We thank you for choosing Kasco
for your fountain and aeration needs and want you to

be completely satised with your purchase.

Important Safety

Please read and follow these extremely important
safety and handling instructions for your Kasco
equipment. Following these instructions will help
ensure your safety and the quality performance of your
equipment.

• Under NO circumstances should anyone enter
the water with the electrical equipment plugged
in and/or in operation. All Kasco equipment is
designed and built for use in water, and control
panels are available with GFCI protection.
However, it is NEVER recommended to enter the
water with the equipment in operation.

• Kasco’s Light Kit is intended for use with a Listed
control panel having a GFCI protected receptacle,

or eld wiring terminals and disconnect switch,

or a timer with a disconnect for use with a GFCI
receptacle. They are intended to be mounted on

a oating fountain or aerator for use in a natural

or man-made body of water to comply with NEC
Article 682.

• Kasco’s Light Kit has not been evaluated for use in
swimming pools, spas or stationary fountains.

• The power connection for the light kit is 120Vac
and MUST be plugged into a GFCI protected

receptacle or GFCI protected eld terminal

connections.

• Caution should be used when dealing with any
electrical and/or moving equipment.

• NEVER run the unit out of water. It could create a
dangerous situation for the operator.

• Extreme caution should be used around water,
especially cold water, as in Spring, Fall, and
Winter, which poses a hazard itself.

• NEVER lift or drag the fountain or light kit by the
power cords. If you need to pull the unit to the
side of the pond, use the anchoring ropes.

• Do not use waders in ponds/lakes that are deep,
with drop-offs, drastic slopes, or soft bottom
material.

• Do not use a canoe or boat that tips easily during
installation

• To reduce the risk of electrical shock, be certain
the light kit is connected to the GFCI protected
lighting circuit of your control panel. For
more information regarding your control panel
instructions, refer to your fountain owner’s manual
or download control panel wiring diagrams from
http://kascomarine.com/instructions.html. A
control panel must be installed a minimum of 5
feet (3m in Canada) from the body of water unless
separated from the body of water by a fence, wall,
or other permanent barrier that will make the unit
inaccessible to persons in the water.

General Instructions

INSPECT THE SHIPMENT
Immediately inspect this shipment for any visible
damages. Also cross reference the “Parts Included”
section to check for part shortages. Shortages should
be reported immediately to your Kasco Marine
distributor or representative and damages reported to
your carrier and Kasco Marine.

Parts Included

LED8012

• A. Light Kit power cord with junction box (1)

• B. 8 puck lights (1) (color depends on purchase)

• C. Dual Lock Fastener Squares (16)

• D. Cable tie (1)

Note: Part A and B are already connected.

TOOLS & SUPPLIES NEEDED

• A. Diagonal Pliers or Cutter for Nylon Cable Tie

LED8012 Assembly Instructions

For ease of assembly, make sure the Aerating Fountain
is completely assembled. Place the assembly upright.

1. Unbundle the 8 puck light kit. Unpeel the back-

ing from one of the dual lock squares and place on the
back of one of the puck lights. (See Fig 1.) Repeat

this on the other 7 puck light xtures.

2

Fig.1

Mounting to Fountain model 2400SF (xStream)

2. There are 8 circular indents on the oat of the

2400SF xStream fountain. Make sure these areas are
clean, free of debris, and dry. Remove the backing
from one of the dual lock squares and stick to the
bottom of one of the indents (See Fig. 2). Repeat to

the other 7 indents of the oat.

Fig 3

Fig 4

Fig 2

3. Place the puck light that has the power cord leading

to the junction box in the indent on the oat that has a

notch for power cords. This would be the same area
where the power cord for the fountain is located. Push
down gently until the puck light snaps in place (Fig 3).

Place the other puck lights in the oat and gently snap

them in place (Fig 4).

4. Cable tie the main power cord after the junction

box to the opposite side of the oat where you cable

tied the fountain power cord. This will help provide
strain relief to junction box and puck lights if the cord
is accidentally pulled. (Fig 5)

Fig 5

3