K-array KX12 User Manual

Page 1
KX12 Ver. 1.4
KX12
USER GUIDE
English
Page 2
KX12 Ver. 1.4
2
SYMBoLS ................................................................................ 3
1. INTRoDUCTIoN ..................................................................... 4
2. KEY fEATURES ...................................................................... 4
3. APPLICATIoNS ....................................................................... 4
4. SAfETY INfoRMATIoN ............................................................ 5
5. UNPACKING ......................................................................... 6
6. PRoDUCT ovERvIEw .............................................................. 6
7. wIRING ................................................................................ 7
8. hoRN oRIENTATIoN ............................................................... 8
9. RIGGING ............................................................................... 9
9.1 SUSPENDING ThE KX12 wITh A fLY BAR.................................................... 9
9.2 wALL-MoUNTING ThE K X12 .................................................................14
9.3 STANDING ThE K X12 oN A KMT SUBwoofER ............................................ 15
10. SERvICE ........................................................................... 20
11. TEChNICAL SPECIfICATIoNS ................................................... 21
12. CERTIfICATIoN ................................................................... 22
Page 3
KX12 Ver. 1.4
3
SYMBoLS
This symbol alerts the user to the presence of recommendations about product’s use and maintenance.
This symbol alerts the user to the presence of recommendations about the product’s use and maintenance.
K-array declares that this device is in compliance with applicable CE standards and regulations. Before putting the device into operation, please observe the respective country-specific regulations!
Waste Electrical and Electronic Equipment (WEEE) Please dispose of this product at the end of its operational lifetime by bringing it to your local collection point or recycling center for such equipment.
This device complies with the Restriction of Hazardous Substances Directive.
Warning: DANGEROUS VOLTAGE. Terminals marked with this symbol carry a risk of electric shock, therefore external wiring connected to these terminals requires installation by a qualified professional or the use of ready-made leads or cords.
Page 4
KX12 Ver. 1.4
4
1. INTRoDUCTIoN
2. KEY fEATURES
3. APPLICATIoNS
Designed to be consistently unique like all the unique K-array products, the KX12 is a radical reinterpretation of a traditional coaxial 12” speaker. Its compact shape and different accessories allow the KX12 to perform as a powerful audio point source or as part of a line array.
When high pressure is needed in the foreground with a rapid depreciation once distanced from the source, the KX12 can meet this demand to become one of the most useful tools for an installer. Similar to the Firenze KH7, an asymmetric 100° by 30° horn with an adjustable orientation gives to the speaker an added value providing two modes of coverage to choose from to meet the needs of different installations.
Additionally, dedicated accessories assist in the set up of joining, flying and stacking the speaker, making it a perfect line array component.
Its steel chassis offers maximum rigidity in a minimum size. The speaker delivers a continuous SPL of 127 dB and has a frequency range of 120 Hz to 19 kHz and it is compatible with all K-array KMT subwoofers.
• Unique performance-to-size ratio
• Asymmetrical horizontal and vertical coverage
• Variable angle array design
• Stainless steel chassis
• Customized colors (only under specific request)
• Clubs, DJ
• Theaters, Concert halls
• Houses of worship
• Portable and installed AV systems
• Cinema and special effects
• Theme parks
• Optimized for KMT18, KMT21, KMT218, KA84
Page 5
KX12 Ver. 1.4
5
4. SAfETY INfoRMATIoN
Warning: failure to follow these safety instructions could result in injury or damage to the device or other property.
IMPORTANT SAFETY INSTRUCTIONS
• Read these instructions.
• Keep this instructions.
• Heed all warnings.
• Follow all instructions and keep all warnings.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or
sold with the apparatus.
• When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tipover.
• Avoiding hearing damage. Professional loudspeakers are capable of producing extremely high sound levels and should be used carefully. Never stand close to loudspeakers driven at high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that over time may sound normal but can be damaging to your hearing. Hearing loss worsens after exposure to a sound level of 90 dB or over for an extended period of time. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected.
• Choking Hazards. This device contains small parts, which may present a choking hazard to small
children. Keep the device and its accessories away from small children.
• Do not make repairs yourself. Never attempt to disassemble, repair or modify the system yourself.
Disassembling the unit may cause damage that is not covered under the warranty. The device contains no user-serviceable parts. Repairs should only be performed by factory trained service personnel.
• Sound distortion. Do not operate speakers for an extended period of time with sound distortion. This
is an indication of malfunction, which in turn can generate heat and result in a fire.
• Carrying, handling and installing the device. The device contains sensitive components. Do not drop,
disassemble, open, crush, bend, deform, puncture, shred, incinerate, paint, or insert foreign objects into it. If your device has been dropped or damaged, unplug the power cable immediately.
• Setup. Set up your device on a stable, horizontal surface. If combined or mechanically connected with
other products, always verify the stability of the resulting system. Install the unit only in a location that can structurally support the weight of the unit and far away from interference with the stability of the system. Ensure the wind does not interfere with the system’s stability, taking extra securities such as chains, weights, ropes or any other certified anchoring systems. Otherwise a unit could fall, causing property damage, personal injury or even death. The system should only be suspended by qualified personnel following safe rigging practices. Securing fixtures to the building structure are vital. To clarify any doubts you may have, seek help from architects, structural engineers or other specialists.
Page 6
KX12 Ver. 1.4
6
13,4in
340mm
7,9in
200mm
12,6in
320mm
4,8in
121,8mm
5. UNPACKIN G
Each K-array speaker is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your new amplifier. If you find any damage, immediately notify the shipping company. Only the consignee may institute a claim procedure regarding the system’s electronic equipment.
6. PRoDUCT ovERvIEw
Weight
12.2 kg (26.9 lbs)
Page 7
KX12 Ver. 1.4
7
7. wIRING
KX12’s internal wiring is designed to pick up the audio power signal from pins 1+ / 1- of a Speakon NL4 connector. Pins 1+ and 1-, such as pins 2+ and 2-, are directly wired from one socket to the other, so that the two sockets are equivalent and can connect the speaker to the amplifier or to another KX12 driven in parallel by the same amplifier channel.
NOTE:
The K-array KA84 amplifier can drive up to two KX12 units per channel
Page 8
KX12 Ver. 1.4
8
8. hoRN oRIENTATIoN
The KX12 features a 12” woofer and a compression driver coupled to an asymmetric horn. Because the horn is asymmetric, its sound dispersion pattern is different in respect to its axes: the sound dispersion is wide along the axis labeled FLOOD and narrow along the axis labeled SPOT.
The horn can be manually rotated 90° using the two handles situated at the front.
In this position the sound dispersion
pattern is wide (FLOOD - 100°) in the
horizontal plane and narrow (SPOT - 30°)
in the vertical plane.
In this position the sound dispersion
pattern is narrow (SPOT - 30°) in the
horizontal plane and wide (FLOOD - 100°)
in the vertical plane.
TIP
If you connect more units together to form a vertical array, make sure to orient all horns in vertical (above picture on the left) so that they are aligned in the same direction of the array. This will assure a wide horizontal coverage with a narrow vertical dispersion.
Page 9
KX12 Ver. 1.4
9
9. RIGGING
K-array offers a variety of dedicated accessories to mount and connect the KX12 speakers for a wide range of applications.
This section highlights the main accessories available for this product.
9.1 SUSPENDING ThE KX12 wITh A fLY BAR
KX12 units can be suspended using the K-FLY2B, a fly bar; K-FLY22, hardware used to connect the first unit to the fly bar; and K-JOINT2B, the hardware that connects a KX12 to the K-FLY22 or to another KX12.
K-FLY 2B K-FLY 22
1. First connect the two parts of a K-JOINT2B to each speaker with the provided 5x16 screws.
K-JOINT2B
Page 10
KX12 Ver. 1.4
10
2. Join the K-FLY2B and the K-FLY22 with the two 8x40 piston pins provided with the system.
3. Connect the first KX12 unit to the fly bar. Secure with the two 8x40 piston pins provided with the
system.
Page 11
KX12 Ver. 1.4
11
4. Insert two joint blocks and secure each of them with the two 5x30 piston pins provided with the
system. The orientation of the joint blocks and the holes used will affect the angle between the fly bar and the KX12, as shown below. We recommend setting an angle of 0° between the fly bar and the first KX12 unit.
If you want to angle the speaker by 0°, +5°, +10° or +15°, position the joint block so that the letter “A” is at the bottom. Plug a piston pin in the hole labeled “A”, adjust the angle of the speaker and plug the second piston pin in the hole corresponding to the desired angle.
If you would like to angle the speaker by -5°, -2.5°, +2.5° or +7.5°, position the joint block so that the letter “B” is at the bottom. Plug a piston pin in the hole labeled “B”, adjust the angle of the speaker and plug the second piston pin in the hole corresponding to the desired angle.
The pictures below show how to regulate the angles
Page 12
KX12 Ver. 1.4
12
5. Position the next unit. Connect the two units with two 8x40 piston pins. Insert the two joints and
regulate the angles as explained on the previous page. Secure with four 5x30 piston pins.
Page 13
KX12 Ver. 1.4
13
6. Repeat Step 5 to connect the other units.
Page 14
KX12 Ver. 1.4
14
9.2 wALL-MoUNTING ThE K X12
The K-WALL2 accessory is used to mount a KX12 unit to a wall.
Page 15
KX12 Ver. 1.4
15
9.3 STANDING ThE K X12 oN A KMT SUBwoofER
KX12 units can be mounted on a KMT subwoofer using the K-FOOT2B-202 and the K-JOINT2B accessories. Excellent examples of this combination are the K-array portable stereo systems KRX202, KRX402 and KRX802.
KRX202 KRX402
KRX802
Page 16
KX12 Ver. 1.4
16
The next step-by-step instructions demonstrate how to mount a KRX802. The mounting procedure for the other systems is not dissimilar.
Below are the accessories needed to mount the system:
K-FO OT 2 B-202 K-JOINT2B
Kit with a K-POLE1 extendable pole
and a K-FLY22 pole adapter.
Connecting hardware which you will
need per KX12 unit.
1. Screw the pole into the subwoofer.
Page 17
KX12 Ver. 1.4
17
2. Insert the K-FLY22 adapter and screw the knob.
3. Connect a K-JOINT2B to each KX12 unit.
Page 18
KX12 Ver. 1.4
18
4. Insert the first KX12 unit. Secure with the two 8x40 piston pins provided with the system.
5. Insert two joint blocks and secure each of them with the two 5x30 piston pins provided with the
system. The orientation of the joint blocks and the holes used will affect the angle between the K-FLY22 and the KX12, as shown in the next page.
Page 19
KX12 Ver. 1.4
19
If you want the to angle the speaker by 0°, +5°, +10° or +15°, position the joint block so that the letter “A” is at the bottom. Plug a piston pin in the hole labeled “A”, adjust the angle of the speaker and plug the second piston pin in the hole corresponding to the desired angle.
If you want the to angle the speaker by -5°, -2.5°, +2.5° or +7.5°, position the joint block so that the letter “B” is at the bottom. Plug a piston pin in the hole labeled “B”, adjust the angle of the speaker and plug the second piston pin in the hole corresponding to the desired angle.
The pictures below show how to regulate the angles
5. Repeat Steps 4 and 5 to add the other units.
Page 20
KX12 Ver. 1.4
20
10. SERvICE
To obtain service:
1) Contact the official K-array distributor in your country. Your local distributor will direct you to the appropriate service center.
2) If you are calling for service, please have the serial number(s) of the unit(s) available for reference.
Ask for Customer Service and be prepared to describe the problem clearly and completely.
3) If the problem cannot be resolved over the phone, you may be required to send the unit in for
service. In this instance, you will be provided with an RA (Return Authorization) number which should be included on all shipping documents and correspondence regarding the repair. Shipping charges are the responsibility of the purchaser.
Any attempt to modify or replace components of the device will invalidate your warranty. Service must be performed by an authorized K-array service center.
Cleaning: Use only a soft, dry cloth to clean the product. Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives. Do not use any sprays near the product or allow liquids to spill into any openings.
Page 21
KX12 Ver. 1.4
21
11. TEChNICAL SPECIfICATIoNS
The content s of this manual are furnished for informational purposes only. K-array s.u.r.l. assumes no responsibilit y for any errors or inaccuracies that may
appear in this manual. K-array s.u.r.l. reserves the right to make modifications without prior notice.
ACOUSTIC S
Power handling 800 + 200 W
Max power 1200 W
(1)
Frequency range (-3 dB) 120 Hz – 19 kHz
(2)
Impedance 8 Ω
SPL 1 W/1mt 102 dB
(3)
Maximum SPL 127 dB (cont.) – 133 dB (peak)
(4)
COVERAG E
Horizontal 100°/30° (depending on horn orientation)
Vertical 30°/100° (depending on hor n orientation)
CROSSOVER
Type External Crossover required
Frequency
High pass @ 120 Hz, 24 dB/oct suggested minimum
TRANSDUCERS
COAXIAL
12” Neodymiun magnet Woofer with 3” voice coil
Neodymium magnet compression driver with 2” Voice Coil
POWER AUDIO IN PUT/OUT PUT
Connector 2 x 4-pin Speakon
Wiring 1+ 1- (Signal IN & LINK ) 2+ 2- (Through)
RECOMMENDED AMPLIFIERS
Type KM T18, KMT 21, KMT218, K A84
CERTIFICATION
IP 21
PHYSICAL
Dimensions
34.0 cm x 32.0 cm x 20.0 cm (13.4“ x 12.6” x 7.9“)
Weight 12.2 kg (26.9 lbs)
Notes for data
1. Maximum RMS applicable power for a musical signal. The reference signal is the one proposed by EIAJ standard
2. With dedicated preset
3. Measured @ 4m then scaled @ 1m
4. Measured with musical signal
New materials and designs are introduced into existing products without prior notice. Present systems may differ in some respects from those presented in this catalogue.
Page 22
KX12 Ver. 1.4
22
12. CERTIfICATIoN
Loading...