Karcher Puzzi 10/1, Puzzi 10/2 Adv User Manual

Puzzi 10/1
Puzzi 10/2 Adv

Deutsch 4
English 12
Français 19
Italiano 27
Nederlands 35
Español 43
Português 51
Dansk 59
Norsk 66
Svenska 73
Suomi 80
Ελληνικά 87
Türkçe 95
Русский 102
Magyar 111
Čeština 119
Slovenščina 126
Polski 133
Româneşte 141
Slovenčina 149
Hrvatski 157
Srpski 164
Български 172
Eesti 180
Latviešu 187
Lietuviškai 194
Українська 201

www.kaercher.com/register-and-win

59662790 01/14

A

1

4

2

MAX

MAX 50°C

CHEM

5

3

6

1.

2.

1.

2.

7

MAX 2L

CHEM

8

9

2

B

1

C

35

34

33

29

26
25 24

28

27

31
30

36

32

17

18

2
3
4

19

20

5

6

16

23

22

21 14

7
8

10

12

9

1115 13

3

Please read and comply with

these original instructions prior
to the initial operation of your appliance and
store them for later use or subsequent own­ers.

– Before initial start-up it is definitely nec-

essary to read the safety information
no. 5.956-251.0!

– The non-compliance of the operating

and safety instructions may lead to
damages of the appliance and to dan­gers for the operator and other persons.

– In case of transport damage inform ven-

dor immediately

Contents

Environmental protection . . . . . EN . . .1

Symbols in the operating in-

structions . . . . . . . . . . . . . . . . . EN . . .1

Proper use . . . . . . . . . . . . . . . . EN . . .1

Overview . . . . . . . . . . . . . . . . . EN . . .2

Start up. . . . . . . . . . . . . . . . . . . EN . . .2

Operation . . . . . . . . . . . . . . . . . EN . . .3

Cleaning methods . . . . . . . . . . EN . . .4

Transport . . . . . . . . . . . . . . . . . EN . . .5

Storage. . . . . . . . . . . . . . . . . . . EN . . .5

Maintenance and care . . . . . . . EN . . .5

Troubleshooting . . . . . . . . . . . . EN . . .5

Accessories and Spare Parts. . EN . . .6

Warranty. . . . . . . . . . . . . . . . . . EN . . .6

EC Declaration of Conformity. . EN . . .6

Technical specifications . . . . . . EN . . .7

Environmental protection

The packaging material can be
recycled. Please do not throw
the packaging material into
household waste; please send it
for recycling.

Old appliances contain valuable
materials that can be recycled;
these should be sent for recy­cling. Batteries, oil, and similar
substances must not enter the
environment. Please dispose of
your old appliances using ap­propriate collection systems.

Notes about the ingredients (REACH)

You will find current information about the
ingredients at:

www.kaercher.com/REACH

Symbols in the operating

instructions

 Danger

Immediate danger that can cause severe
injury or even death.

몇 Warning

Possible hazardous situation that could
lead to severe injury or even death.

Caution

Possible hazardous situation that could
lead to mild injury to persons or damage to
property.

Proper use

This device is intended for commercial use
as a wet cleaning device for carpets as de­picted in these operating instructions as
well as in the descriptions and safety notes
in the enclosed brochure "Safety indica­tions for brush cleaning devices and spray
extraction devices".

12 EN

– 1

Overview

Quick start instructions

Illustration
1 Connect spray/suction hose to the el-

bow,
Connect spray/suction hose to the ap­pliance

2 Prepare cleaning solution,

Fill up the fresh water tank
3 Select operating mode
4 Cleaning
5 Empty the fresh water tank
6 Empty wastewater container
7 Fill fresh water tank (without detergent),

Flush appliance
8 Clean lint trap,

Clean fresh water sieve
9 Allow appliance to dry

Device elements

Illustration
1 Hand nozzle for upholstery cleaning

(Puzzi 10/1 only)
2 Cable hook
3 Adapter for accessories (homebase)
4 Holder for accessories
5 Power cord
6 Quick start instructions
7 Fresh water tank
8 Fresh water sieve
9 Switch for spraying
10 Switch for vacuuming
11 Casing
12 Nameplate
13 Steering roller
14 Spray hose connection
15 Socket for additional brush washing

head PW 30/1 (Puzzi 10/2 Adv only)
16 Suction hose connection
17 Container for defoaming agent (Puzzi

10/2 Adv only)
18 Cover
19 Storage compartment for detergent

tabs (Puzzi 10/2 Adv only)
20 Carrying handle of the appliance
21 Floor nozzle for carpet cleaning
22 Carpet adapter

23 Unlocking device of the floor nozzle
24 Suction pipe
25 Nozzle mouth piece
26 Union joint
27 Handle
28 Bender
29 Lever on the manifold
30 Spray hose
31 Suction hose
32 Spray/suction hose
33 Dirt water reservoir, detachable
34 Carrying handle of the wastewater con-

tainer
35 Seal on the lid
36 Fluff filter

Start up

 Check high power cable, extension ca-

bles and hoses for damage every time

before use.

Attaching the Accessories

 Attach the suction pipe to the floor noz-

zle and hand-tighten the union nut on

the floor nozzle.
 If required, slide the handle onto the

suction pipe and hand-tighten it in the

desired position.
 Place the elbow over the suction pipe

and tighten the union joint on the elbow

fingertight.
 Insert the suction hose into the suction

hose connection on the appliance.

Attach the coupling of the spray hose to

the spray hose connection of the appli-

ance and snap in place.
 Connect the suction hose to the elbow.

Connect the coupling of the spray hose

with the manifold and snap in place.

Prepare cleaning solution

몇 Warning

Health risk, risk of damage. Observe all in­dications on the detergent used.

 Mix fresh water and detergent in a clean

container (use the concentration rec-

ommended for the detergent).

Dissolve detergent in the water.

– 2

13EN

Note: Warm water (max. 50°C) will in­crease the cleaning effect. Verify the tem­perature resistance of the surface to be
cleaned.
Note: For considerate treatment of the en­vironment use detergent economically.

Fill up fresh water reservoir

 Fill detergent solution into the fresh wa-

ter reservoir. The fill level must not ex­ceed the "MAX" mark.

Defoaming agent

Note: When cleaning previously sham-

pooed carpets, foam is generated in the
wastewater container. This formation of
foam can be prevented by adding a de­foaming agent.
Puzzi 10/1 only:
 Put defoaming agent (optional accesso-

ry) into the wastewater container.

Puzzi 10/2 Adv only:

 Open container for defoaming agent.
 Fill in defoaming agent (optional acces-

sory).

Replacing the carpet adapter

 Push the unlocking device of the floor

nozzle on one side.

 Swivel out and remove the carpet

adapter.

 Insert a new carpet adapter and snap

the locking device in place.

Operation

Working with attachments

Puzzi 10/2 Adv only:
Note: There is an additional socket to con­nect electrical accessory devices.

 Danger

Risk of injury and damage! The socket is
only intended for the direct connection of
the additional brush washing head PW 30/
1 to the Puzzi 10/2 Adv. Any other use of
the socket is not permitted.

Turning on the Appliance

 Plug in the main plug.
 Press the suction switch to turn on the

suction turbine.
 Press the spray switch to switch on the

spray pump.

Cleaning

Caution

Risk of damage. Check the object to be
cleaned prior to using the appliance in an
inconspicuous place for colour fastness
and water resistance.

 Operate the lever on the manifold in or-

der to spray the cleaning solution.
 Run across the surface to be cleaned in

overlapping paths. Pull the nozzle back-

wards (do not push).
 In case of work interruptions, the floor

nozzle can be stored in the handle.

Turn off the appliance

 Switch off the spray and suction switch-

es.
 Pull out the mains plug.

Empty wastewater container

 If the dirt water reservoir is full, switch

off the suction and spray switches.

 Remove the lid.
 Remove the wastewater container from

the appliance and drain it.

Empty the fresh water reservoir

 Turn off the appliance.
 Shortly activate the lever on bender to

decrease the pressure.
 Separate bender from the spray/suction

hose.
 Insert the suction hose into the fresh

water reservoir.
 Press the suction switch to turn on the

suction turbine.
 Empty the fresh water reservoir and

switch the appliance off.

 Remove the lid.
 Remove the wastewater container from

the appliance and drain it.

14 EN

– 3

Flush appliance

 Connect the manifold (with suction pipe

and nozzle) to the suction hose.

 Connect the coupling of the spray hose

with the manifold and snap in place.

 Fill approx. 2 litres of fresh water into

the fresh water reservoir.

Do not add any detergents.

 Press the spray switch to switch on the

spray pump.

 Hold floor nozzle over a drain.
 Activate lever on bender and flush the

appliance for appr. 1 to 2 minutes.

 Turn off the appliance.

After each operation

 Flush appliance.
 Empty the wastewater container and

clean it under running water.

 Empty the fresh water reservoir.
 Clean the outside of the appliance with

a damp cloth.

 Remove all water from the appliance

prior to longer periods of non-use to
avoid offensive odours.

 Allow appliance to dry thoroughly: Re-

move or move lid sideways.

Storing the Appliance

 Place the appliance in a dry room and

secure it from unauthorized use.

Cleaning methods

Normal soiling

 Spray and suction off detergent solution

in one work cycle.
Note: Repeated suctioning without spray­ing will shorten the drying time.

Strong soiling or stains

 Apply detergent solution with suction

turbine turned off and soak for 10 to 15
minutes.

 Clean the surface just like with normal

soiling.

 In order to further improve the cleaning

result, the surface can be recleaned us­ing clear, warm water.

Upholstery cleaning

 Puzzi 10/1 only:

Attach hand nozzle instead of the floor
nozzle.

 With sensitive materials, use less deter-

gent and spray the surface at a distance
of approx. 200 mm. Then simply vacu­um off.

Cleaning tips

– Highly soiled spots should be pre-

soaked and the detergent solution
should soak 5 to 10 minutes.

– Always work from the light to the shade

(from the window to the door).

– Always work from the cleaned to the un-

cleaned surface.

– The more sensitive the surface (oriental

rugs, berbers, upholstery material) the
lower the cleaning solution concentra­tion should be.

– Rugs with jute backing can shrink if too

much water is used and can bleed col­ours.

– Brush high-fiber rugs in the direction of

the weave after cleaning (using a fiber
brush or a scrubber).

– Water-proofing the fabric using Care

Tex RM 762 after the wet cleaning pre­vents a quick resoiling of the textile sur­face.

– Do not step on cleaned surfaces until

they have dried and do not place furni­ture on them to avoid pressure spots or
rust stains.

– 4

15EN

Detergent

Carpet and upholstery
cleaning

Defoaming RM 761
Waterproofing carpets RM 762

For further information, please request
product information sheet and EU safety
data sheet of the relevant detergent.

RM 760 powder
RM 760 tabs
RM 764 liquid

Transport

Caution

Risk of injury and damage! Observe the
weight of the appliance when you transport
it.

Illustration
 For transport, place suction pipe on the

carrying handle and place the spray/

suction hose on top of the appliance.

Wind up the mains cable and hook it

into the cable hook.
 When transporting in vehicles, secure

the appliance according to the guide-

lines from slipping and tipping over.

Storage

Caution

Risk of injury and damage! Note the weight
of the appliance in case of storage.

This appliance must only be stored in inte­rior rooms.

Maintenance and care

 Danger

Danger of injury by electric shock.
First pull out the plug from the mains before
carrying out any tasks on the machine.

Clean the fluff filter

 Remove the lid.
 Remove the wastewater container from

the appliance.
 Regularly clean the lint trap using a

brush.

Cleaning the fresh water sieve

 Unscrew the fresh water sieve.
 Regularly clean the fresh water sieve

under running water.

Cleaning the nozzle

 Unscrew the covering nut.
 Clean nozzle mouthpiece.

Troubleshooting

 Danger

– Danger of injury by electric shock.

First pull out the plug from the mains be­fore carrying out any tasks on the ma­chine.

– Get the electrical components checked

and repaired only by authorised cus­tomer service persons.

Appliance is not working

 Check the receptacle and the fuse of

the power supply.

 Check the power cable and the power

plug of the device.

 Turn on the appliance.

No water exiting from nozzle

 Fill up fresh water reservoir.
 Check the couplings on the spray hose

for proper seating.

 Clean or replace nozzle tip.
 Clean the sieve in the fresh water reser-

voir.

 Spray pump defective, contact after-

sales service.

Spray stream one-sided

 Clean nozzle mouthpiece.

Insufficient vacuum performance

 Check the correct positioning of the lid.
 Clean seal on lid and surface on the ap-

pliance.

 Clean the fluff filter.
 Check suction hose for blockages;

clean if required.

16 EN

– 5

Spray pump loud

 Fill up fresh water reservoir.

Heavy formation of foam in the

wastewater container

 Add the defoaming agent into the

wastewater container or fill up the con-

tainer for the defoaming agent.

Customer Service

If malfunction can not be fixed, the de­vice must be checked by customer ser­vice.

Accessories and Spare Parts

– Only use accessories and spare parts

which have been approved by the man-

ufacturer. The exclusive use of original

accessories and original spare parts

ensures that the appliance can be oper-

ated safely and trouble free.

– At the end of the operating instructions

you will find a selected list of spare parts

that are often required.

– For additional information about spare

parts, please go to the Service section

at www.kaercher.com.

Warranty

The warranty terms published by the rele­vant sales company are applicable in each
country. We will repair potential failures of
your appliance within the warranty period
free of charge, provided that such failure is
caused by faulty material or defects in man­ufacturing. In the event of a warranty claim
please contact your dealer or the nearest
authorized Customer Service centre.
Please submit the proof of purchase.

EC Declaration of Conformity

We hereby declare that the machine de­scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.

Product: Spray extraction device
Type: 1.100-xxx
Type: 1.193-xxx
Relevant EU Directives

2006/42/EC (+2009/127/EC)
2004/108/EC
2011/65/EU

Applied harmonized standards

EN 55014–1: 2006+A1: 2009+A2: 2011
EN 55014–2: 1997+A1: 2001+A2: 2008
EN 60335–1
EN 60335–2–68
EN 61000–3–2: 2006+A1: 2009+A2: 2009
EN 61000–3–3: 2008
EN 62233: 2008
EN 50581

Applied national standards

-

5.957-534

The undersigned act on behalf and under
the power of attorney of the company man­agement.

CEO

Authorised Documentation Representative
S. Reiser

Alfred Kärcher GmbH Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Phone: [phone]
Fax: [phone]

Head of Approbation

Winnenden, 2013/12/01

– 6

17EN

Technical specifications

Puzzi 10/1 Puzzi 10/2 Adv

Mains voltage V EU: 220-240 EU: 220-240

V GB: 230-240 GB: 230-240
V AU: 240 AU: 240

V AR: 220 AR: 220
Frequency Hz 1~ 50/60 1~ 50/60
Type of protection -- IPX4 IPX4
Protective class II II

Nominal performance of blower motor W 1100 1100
Power (tot.) W -- 1350
Air volume (max.) l/s 54 54
Negative pressure (max.) kPa (mbar) 22 (220) 22 (220)
Spray pump performance W 40 80
Spray pressure MPa 0,1 0,2
Spray pressure (max.) MPa 0,3 0,3
Spray volume I/min 1 2
Temperature of the cleaning solution

(max.)
Filling quantity of fresh water l 10 10
Fill volume wastewater l 9 9
Appliance socket performance (max) W -- 250
Length x width x height mm 705 x 320 x 435 705 x 320 x 435
Typical operating weight kg 10,7 11,4
Max. ambient temperature °C +40 +40

Values determined to EN 60335-2-68

Sound pressure level L

Uncertainty K

pA

pA

Hand-arm vibration value m/s
Uncertainty K m/s

Power cord H05VV-F 2x1,0 mm

Part no.: Cable length
EU 6.650-363.0 7.5 m
GB 6.650-380.0 7.5 m
AU 6.650-385.0 7.5 m
AR 6.650-382.0 7.5 m

°C 50 50

dB(A) EU: 74 EU: 74
dB(A) GB: 76 GB: 76
dB(A) 1 1

2

2

2

<2,5 <2,5
0,2 0,2

18 EN

– 7