Full HD Dash camera 3.0" IPS Screen
with Rear Camera & 24 hr Parkmode
KPT-522
USER MANUAL
CONTENTS
1.0 CAUTION .............................................................................................................................4
1.1 Battery Warning .............................................................................................................5
1.2 Product Information ......................................................................................................6
2.0 INTRODUCTION .................................................................................................................7
2.1 Package Contents ..........................................................................................................8
2.2 Product Overview ...........................................................................................................9
3.0 BUTTON FUNCTIONS ......................................................................................................10
4.0 GETTING STARTED ...........................................................................................................11
4.1 Inserting a Micro SD Card ...........................................................................................11
4.2 Removing a Micro SD Card ........................................................................................ 12
4.3 Installing the KPT-522.................................................................................................. 13
4.4 Adjusting the Angle of the KPT-522 ......................................................................... 14
4.5 Installing the Rear Camera ........................................................................................ 15
4.5.1 Installation Guide ........................................................................................... 15
1
4.5.2 Rear Camera Wiring Diagram .................................................................... 16
4.5.3 Rear Camera Features ................................................................................. 17
4.6 Connecting to Power ...................................................................................................18
4.7 LED Indicator ................................................................................................................ 19
5.0 POWERING THE KPT522 ONOFF ...............................................................................19
5.1 Auto Power On/Off ..................................................................................................... 19
5.2 Manual Power On ......................................................................................................... 19
5.3 Manual Power Off ...................................................................................................... 20
5.4 Reset the Car DVR ...................................................................................................... 20
6.0 INITIAL SETTINGS ........................................................................................................... 20
6.1 Formatting the Inserted Micro SD Card ................................................................ 20
7.0 SETTING THE TIME AND DATE ...................................................................................... 21
8.0 VIDEO MODE ....................................................................................................................22
9.0 INTERFACE ......................................................................................................................23
2
9.1 Video Mode .................................................................................................................... 23
9.2 Setup Menu ...................................................................................................................24
10.0 VIDEO MENU ....................................................................................................................25
11.0 PICTURE MODE ................................................................................................................29
12.0 PLAYBACK ....................................................................................................................... 30
13.0 WARRANTY TERMS & CONDITIONS ............................................................................31
3
1.0 CAUTION
4
• Ensure you are using your Car Dash Cam within your countries’ road laws.
Please make sure you are familiar with your local road legislation before use.
• Avoid leaving your Dash Cam in direct sunlight for extended periods of time in
an unventilated space.
• Please set time and date before you use this device to record.
• The notiications given by the Car Dash Cam are suggestions only, please drive
to the actual conditions.
• The system is to be used only for non-commercial use, within the limits
permitted by the relevant laws.
• Avoid using the Car Dash Cam near any devices that emit radio interference
(e.g. Microwave Ovens).
• It is considered normal operation for the Car Dash Cam to get warm during
use.
1.1 BATTERY WARNING
Always charge the Car Dash Cam using the provided charger. Improper charging of
the Car Dash Cam and may result in failure of the internal battery.
Never dismantle the Car Dash Cam or expose the internal battery.
Do not dispose of the Car Dash Cam in ire.
Dispose of the Car Dash Cam observing local regulations being mindful of the
internal battery.
Do not attempt to replace or expose the internal battery.
5
NOTES ON INSTALLATION
• It is advised that the Car Dash Cam is installed near the rear view mirror, at
the top centre of the windshield for optimal operation.
• Make sure that the lens is within the range of the windscreen wiper to ensure
a clear view when it rains.
• Do not touch the lens with your ingers. Finger prints left on the lens will result
in unclear videos or photos. If photos or videos are blurred, please clean the
lens gently with a microibre cloth.
• Do not install the device on a tinted window. Doing so may damage the tint
ilm and restrict the Car Dash Camera's recording capabilities.
• It is recommended to install the rear camera near your license plate to provide
an unhindered view from the rear of your vehicle.
• Only use the included cable to power the Car Dash Cam.
• The KPT-522 is designed to be constantly connected to the included power
supply, and is NOT designed to be used solely with the camera’s built in
battery.
1.2 PRODUCT INFORMATION
For latest manual and product updates please visit our website at
www.kapturecam.com.au or www.kapturecam.co.nz
6
2.0 INTRODUCTION
Thank you for purchasing a Kapture Dash Cam. Please read through instructions
before attempting to install or use this product.
This User guide is designed to assist with the day to day operation of the KPT-522.
Before attempting to use or install your Kapture KPT-522, please ensure you have
read and understood all of the safety notes below.
• Avoid leaving your KPT-522 in direct sunlight for extended periods of time in an
unventilated space.
• Do not expose your KPT-522 to liquids, excessive dusty conditions or
temperatures exceeding 60°C.
• Only use the included cables to power and charge the KPT-522.
• Only use the rear camera supplied in the packaging.
• Please do not attempt to adjust the KPT-522 position or settings whilst you are
operating your vehicle.
• Please clean the windshield thoroughly removing all dust and dirt particles
before ixing the adhesive mount.
• Since the mount sticks on the wind shield with 3M mount, please ensure that
the position of the camera is best located to capture maximum area.
7
• We suggest you to power-on the dash camera and test the playback image on
screen irst prior to removing the 3M tape for installation.
• Only remove the 3M tape when you are satisied with the dash camera
placement and image position are delivering the best possible image and view
of the road ahead.
• Ensure you are using your KPT-522 within your countries’ road laws. Please
make sure you are familiar with your local road legislation before use.
2.1 PACKAGE CONTENTS
KPT-522
Dash Cam
Car Charger
User Guide
8
Dash Cam
3M Mount
Spare 3M
Adhesive
Rear Camera
with 6M Cable
Rear Camera
Mount Screws
2.2 PRODUCT OVERVIEW
1. Micro SD card slot*
2. Up Button
3. Menu Button
4. Down Button
5. HDMI Port/Rear Camera In
6. Slot for ixing mount
7. Mini USB power socket
8. Recording Indicator LED
9. Display Screen
10. Rec / OK Button
11. Mode Button
12. Lock Recording Button
13. ON / OFF Power Button
14. Microphone
15. Reset
16. Lens
17. Power ON LED Indicator
17 10
1
2
3
98
4
765
11
12
13
1514
16
9
3.0 BUTTON FUNCTIONS
MODE BUTTON
When Device is not recording, press the M button to switch between Video Mode /
Photo Mode / Play Back mode.
OK BUTTON
Press the OK Button to start/stop video recording in Video mode.
Press the OK Button to take photo in Camera mode.
Press the OK Button to play/pause current video on playback mode.
LOCK FILE BUTTON
When DVR is recording, Press Lock Button to lock the current ile. Locked ile won't
be over recorded during loop recording.
POWER BUTTON
Press and hold the Power Button to Power Off the Device. Press once to switch
LCD Screen Off however DVR will continue recording.
DOWN BUTTON
In Settings menu use the down key to toggle between the settings.
Press to turn On/Off the inbuilt Microphone.
10
MENU BUTTON
Press to enter or exit the Settings Menu.
UP BUTTON
In the Settings menu use the Up Button to toggle between the settings.
RESET BUTTON
Press to reset to factory settings.
MIC
Microphone Position
TF CARD SLOT
Micro SD Card Slot. Please use Maximum 32 GB, Class 10 and above.
USB INTERFACE
Mini USB Power cable to connect with power adapter provided in the packaging.
4.0 GETTING STARTED
4.1 INSERTING A MICRO SD CARD
With the Car DVR turned off and the screen facing towards you insert your Micro
SD Card (not included) in the slot on the right side of the KPT-522 with the text on
the Micro SD card away from you. Push the memory card in until a click is heard.
11
4.2 REMOVING A MICRO SD CARD
Ensure that the KPT-522 is powered off, and with your thumbnail press in the Micro
SD Card until a click is heard. The Micro SD Card will eject from the
KPT-522 when released.
NOTE:
• Micro SD Card is not included.
• Do not remove or insert the memory card while the Car DVR is turned on as
this may damage the memory card or corrupt the memory cards stored data.
• Please use a Class 10 or higher rated micro SD card with a maximum capacity
of 32GB.
• Please format the Micro SD card before the initial use.
• When removing the memory card, be careful as the card may eject quickly.
12
4.3 INSTALLING THE KPT522
1. Connect the Window mount from the top of the DVR and rotate the wheel
(See Fig 1 on page 14) clock wise till it is tight.
2. Please follow the instructions on page 6 before continuing.
3. Remove the protective stickers from the Car DVR and the 3M Mount.
4. Press the mount base irmly against the windscreen and hold for 30 seconds.
5. Insert the power cable adapter onto the dash camera power socket.
6. Rear camera connector has to be inserted in HDMI port of the dash camera.
NOTE:
• It is advised that the KPT-522
is installed in the centre of the
windscreen behind the rear view
mirror.
13
4.4 ADJUSTING THE ANGLE OF THE KPT522
1. Loosen the Angle Locking Wheel on the mounting bracket, and adjust the
vertical and horizontal angle of the camera.
2. Tighten the Angle Locking Wheel to lock the position of the camera.
(Fig .1) Window Mount
14
Mounting
Lock Wheel
Angle Locking
Wheel
3M adhesive
Sticker
4.5 INSTALLING THE REAR CAMERA
4.5.1 INSTALLATION GUIDE
1. Select a lat and centred location near the number plate lamp at the rear of
the vehicle to mount camera.
2. Attach tape to the bracket of the camera to hold
the camera in position while installing, and drill two
small holes, one for the irst screw, the second to
run the reverse camera cable through.
3. Use a screw driver to ix the irst screw, leaving the screw loose enough to
adjust the camera.
4. Insert the camera wire through the intended drilled
hole checking the installation position.
15
5. Mark the position suitable for the second screw
and drill a small hole for it.
6. Fix the second screw and securely tighten both
screws.
4.5.2 REAR CAMERA WIRING DIAGRAM
Rear Camera Reversing Light Wire6M Rear Camera Cable
16
4.5.3 REAR CAMERA FEATURES
After successfully installing and connecting of the rear camera into the main DVR,
the rear camera will be displayed on the Dash Cam's 3.0" IPS Screen.
Both Cameras will instantaneously start recording after DVR is powered ON.
Both Front and Rear Camera images will now be displayed on your Dash Camera's
3.0" IPS Screen, you can switch between by using the UP key.
Display can switch between:
1. Full Front Camera view
2. Full Rear Camera view
3. Half Front and Rear view
When your vehicle is in reverse gear, the display will change to the Rear Camera
view with Reversing Grid Lines to assist the driver when reversing / parking.
17
4.6 CONNECTING TO POWER
Only use the included charger to power and charge the Car DVR.
1. Once the Car DVR is securely installed on your vehicle’s windscreen, plug the
DC Power Plug into your vehicle’s cigarette lighter.
2. Run the power cable along your vehicle’s console and windscreen and plug the
USB Micro plug into the Car DVR and the USB A end into the DC Power Plug.
NOTES:
• It is recommended that the Car DVR is installed behind your vehicle’s rear
view mirror.
• Make sure that the camera view is not obstructed by any window tint or any
other objects.
• The KPT-522 is designed to be constantly powered by the included DC Power
Plug. The internal battery is designed to hold saved settings and power the
camera when in Park Mode. The battery is NOT designed for primary use.
18
4.7 LED INDICATOR
• Flashing blue light indicates recording is in progress.
• Flashing red light indicates the internal battery is charging.
NOTE:
• The KPT-522 is designed to be constantly powered by the included DC Power
Plug. The internal battery is designed to hold saved settings and power the
camera when in Park Mode. The battery is NOT designed for primary use.
5.0 POWERING THE KPT522 ONOFF
5.1 AUTO POWER ONOFF
When the Car DVR is correctly installed and connected to your vehicle’s 12v power
supply, the Car DVR will automatically power up and start recording when the
vehicle accessories are activated.
5.2 MANUAL POWER ON
Hold the Power button on the lower right hand side of the camera until the
Kapture start up screen appears.
19
5.3 MANUAL POWER OFF
Make sure that recording has been stopped and then press the Power button
on the lower right hand side of the car DVR. After powering down the device please
wait for 10 seconds before turning the Car DVR back on.
5.4 RESET THE CAR DVR
If the Car DVR does not function normally, try restarting the car DVR. To restart
the car DVR, using a small pin press and hold the Reset button on the bottom side
of the camera.
6.0 INITIAL SETTINGS
Before using the Car DVR we recommend Formatting the Inserted Micro SD Card
and setting the correct Time and Date.
6.1 FORMATTING THE INSERTED MICRO SD CARD
Formatting the Micro SD card will delete all information on the inserted Micro SD
Card and prepare the card for use with the Car DVR.
1. Press the Button to stop the Car DVR from recording.
2. Press the Menu Button to enter the Settings Menu.
3. Use the and Buttons to navigate the Settings Menu and highlight the
Format setting and press the right to select.
20
4. Select SD Card and press the OK Button.
5. Press the OK Button to conirm.
NOTES:
• Menus cannot be accessed while the camera is recording. Please stop the
recording before attempting to access the menu.
• Formatting your Micro SD Card will delete all iles from the card. Once these
iles have been deleted you will not be able to recover them.
7.0 SETTING THE TIME AND DATE
Setting the Time and Date allows you to stamp your footage with the time as a
reference.
1. Press the Button to stop the Car DVR from recording.
2. Press the Button to enter the Settings Menu.
3. Use the and Buttons to navigate the Settings Menu and highlight the
Date/Time setting and press the right button to select.
21
4. Use the and buttons to edit the selected digit and the right
NOTES:
• Menus cannot be accessed while the camera is recording. Please stop the
• Once the time and date is set, it can be stamped onto your footage using the
8.0 VIDEO MODE
When the Car DVR is powered up the video screen will start by default. In this
screen recording will automatically start and can be stopped by pressing the
Button. To access the Video Menu, ensure that the Car DVR is not recording then
press the button.
22
button to conirm and progress to the next digit. The inal ield sets the format
that the date will be presented in, pressing the button with this ield
highlighted will save the date and time and return you to the settings menu.
recording before attempting to access the menu.
Date Stamp setting. Please see section Date Stamp for more details.
9.0 INTERFACE
9.1 VIDEO MODE
1 2 3
11 12
1. Video Mode: Number 3 shows the loop recording duration.
2. Resolution: 1080 FHD Video Recording Resolution.
3. Duration: 00:00:01 Loop Recording timer.
4. Motion Detection: Displays Motion Detection.
4 8 9 105 6 7
23
5. Lock File: Current Recorded File Locked indicator.
6. Park Mode: The highlighted bar indicates the sensitivity of Park mode with 1
7. G-Sensor: The highlighted bar indicated the sensitivity of G-Sensor with 1 Bar
8. Microphone: Turns on or off the Microphone.
9. Micro SD Card: Indicates inserted SD Card.
10. Battery: Indicates battery level.
11. Date: (01/01/2019)
12. Time: (00:00:01)
9.2 SETUP MENU
1. Press to stop Recording.
2. Press the Menu button to enter into the Settings Menu.
3. Press the and Button to select the setting you wish to change.
4. Press Button on your selected option.
5. New Setting will be shown on the top left of the screen and also on the
24
Bar indicates Low Sensitivity.
indicates Low Sensitivity.
selected setting icon.
10.0 VIDEO MENU
Menu Select Settings Description
Resolution 1080P FHD
Loop
Recording
720P FHD
Off / 1 , 3 or 5
Minutes
Higher resolution gives your footage more detail
but uses more storage space.
Lower resolution saves storage space.
Default: 1080P
Loop Recording deines the length of time the
KPT-522 records before creating a new ile. Using
the Off setting will record the longest possible
loops under the ile size of 1 GB (around 5 minutes).
Default: 3 Mins
Photo
Resolution
12M 4032 x 3024
8M 3264 x 2448
5M 2592 x 1944
2M 1920 x 1080
Higher resolution gives your footage more detail
but uses more storage space.
Lower resolution saves storage space.
Default: 12M
25
VIDEO MENU CONT'
Menu Select Settings Description
Language Select
Date/Time Set Date and
G-Sensor Off / Low /
Park Mode Off / Low /
26
Language
Time
Medium / High
Medium / High
Select Menu Language.
Default: English
Using the Up/Down and OK buttons to enter the
date and time (24hr clock) to stamp onto your
footage. Once you have inished use the Menu
button to save and return to the Settings Menu.
To adjust the sensitivity of the G-sensor.
High is the highest sensitivity and Low is the lowest.
Default: Low
Park Mode helps to make your car safe by recording
the video even when the Engine is switched off.
Your DVR will record the incidents when ever it
detects an impact and the G-Sensor is triggered.
Park Mode will record a maximum of 10 instances
during a 24 hour period, once the battery has been
fully charged.
Default: Off
VIDEO MENU CONT'
Menu Select Settings Description
Motion
Detection
Number
Plate
Stamp
Date
Stamp On
Microphone Off / On Turning this setting off mutes the built in
Beep sound Off / On Mutes control for Key beeps.
Off / On DVR will stop recording if it doesn’t detect any
Input Number
Plate
Off / On Select On/Off to have the date and time stamped
motion and will immediately start recording if it
detects motion.
Default: Off
Input your car number plate and it will be
watermarked on the recorded footage.
on the recorded Video.
Default: On
microphone.
Default: On
Default: On
27
VIDEO MENU CONT'
Menu Select Settings Description
Auto
Display Off
Flicker 50Hz / 60 Hz Screen Hz setting.
Format Cancel / OK Format the inserted Micro SD Card, deleting all
Default
Setting
Version OK Displays the installed irmware version.
28
Off / 1 min / 3
mins / 5 mins
Restore factory
settings
Auto Screen Saver setting determines the amount
of time before the display screen turns off.
(KPT-522 will keep on recording even the display
is Off).
Default : Off
Default: 50 Hz
photos, videos and data.
Cancel / OK
11.0 PICTURE MODE
Picture
Resolutions
1. Press OK to Stop Recording.
2. Press M (Mode Key) once to enter Picture Mode.
3. Press OK Key to take pictures.
SD Card
Battery
Indicator
29
12.0 PLAYBACK
Video Play/
Pause
File Name
30
Battery
Resolution
of recorded
Video
1. Press the OK Button once to Stop Recording.
2. Press M (Mode Key) twice to enter Playback Mode.
3. Press and button to select the desired ile to be played back.
4. Press the OK button to Playback selected video ile and then press again to
pause.
13.0 WARRANTY TERMS & CONDITIONS
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
This warranty is provided in addition to your rights under the Australian Consumer
Law. Directed Electronics warrants that this product is free from defects in
material and workmanship for a period of 12 months from the date of purchase
or for the period stated on the packaging. This warranty is only valid where you
have used the product in accordance with any recommendations or instructions
provided by Directed Electronics.
This warranty excludes defects resulting from alterations of the product, accident,
misuse, abuse or neglect. In order to claim the warranty, you must return the
product to the retailer from which it was purchased or if that retailer is part of
a National network, a store within that chain, along with satisfactory proof of
purchase. The retailer will then return the goods to Directed Electronics.
31
Directed Electronics will repair, replace or refurbish the product at its discretion.
The retailer will contact you when the product is ready for collection. All costs
involved in claiming this warranty, including the cost of the retailer sending the
product to Directed Electronics, will be borne by you.
Directed Electronics Address: 44 Translink Drive, Keilor Park Victoria 3042
Ph: +61 03 8331 4800
Email: service@kapturecam.com.au
32
33
V1.0
YOUR EYEWITNESS ON THE ROAD™
All Images, Information and Content are Copyright © 2019 Directed Electronics
Australia Pty Ltd. All Rights Reserved.
www.kapturecam.com.au | www.kapturecam.co.nz www.directed.com.au | www.directed.co.nz
Loading...