KAPSCH TRAFFICCOM CANADA 802120A User Manual
Kapsch TracCom
Janus
®
HOTPass
®
Interior Transponder
Mounting Instructions
HOV Lane Switch Position
Standard Toll Switch
The HOTPass® interior transponder mounts on the vehicle windshield. The preferred mounting
location is between the rooine and the rear view mirror post. If there is not enough room in the
preferred mounting location to accommodate the HOTPass
mounted beside the rear view mirror post. The HOTPass
®
transponder, the transponder can be
®
transponder is secured using 3M
Lock™ fasteners.
Requirements
WARNING: For safety purposes, select and move the
switch into the desired position and function only when
the vehicle is standing, parked or otherwise not in motion; failure to heed this warning may result in serious
injury or death.
For reliable operation of the transponder, the vehicle must be
equipped with only one transponder while passing through a toll
facility. Other transponders present in or on the vehicle must be
switched o or enclosed in an RF shield.
The mounting location must provide direct line-of-sight
communication between the transponder and the toll facility
overhead antenna.
Do not mount the HOTPass
®
transponder on vehicles:
with non-metallic roofs.
with windshields covered in RF-blocking material (ex. metal oxide).
with a metallic center windshield dividing post.
without center-mounted rear view mirrors.
Handheld mobile communication devices must not be located within
12 in. of the transponder.
Metal objects (except for the rear view mirror and the roof) must not
be located within 6 in. of the transponder.
HOTPass® transponders cannot be used where local regulations
prohibit mounting transponders on the windshield.
Apply Dual Lock™ fasteners in accordance with 3M™ document.
70 -0709-4029-4.
™
Dual
HOTPass ® Interior Transponder
Mounting
1. Select a mounting location on the front windshield. The
®
HOTPass
more that 2 in. from the rooine. The preferred mounting
location is between the rooine and the rear view mirror
mounting post, with a minimum of 1/2 in. between the
transponder should be mounted 1/2 in. but no
1/2 in. preferred
2 in. maximum
orientation
arrow
rooine
transponder and the rear view mirror post.
switch
2. If there is insucient space in the preferred location, select an
alternate mounting location beside the rear view mirror post.
3. Two 3M™ Dual Lock™ fasteners on the back of the HOTPass®
transponder are used to mount the transponder to the windshield.
Prepare the mounting location in accordance with 3M™ document
70 -0709 - 4029-4.
4. Remove the protective backing from the two 3M™ Dual Lock™
fasteners.
5. Firmly press the HOTPass® transponder against the windshield in
the mounting location, ensuring the orientation arrows are pointing
skyward.
6. Maintain pressure for 15 seconds to ensure a good bond.
7. Remove the transponder by lifting any corner with sucient force
to separate the Dual Lock™ fasteners. Do not reuse the Dual Lock
fasteners after removing them from the windshield. Obtain new
fasteners after removing them from the windshield. Obtain new
fasteners as required.
1/2 in. minimum
rear view mirror post
Preferred Mounting Location - Front View
orientation arrow
rear view
mirror post
1/2 in. preferred
2 in. maximum
rooine
1/2 in. minimum.
1-1/2 in. maximum
©Kapsch TracCom Canada Inc. All rights reserved. Subject to alteration without notice
Alternate Mounting Location - Front View
3M™ Dual Lock™
™
HOTPass® Transponder - Rear View
FCC License Notice - This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.
Kapsch Group
The Kapsch Group and its entities Kapsch TracCom, Kapsch CarrierCom and Kapsch BusinessCom are specialised in the future-oriented market
segments of Intelligent Transportation Systems (ITS) and Information and Communication Technology (ICT). Kapsch. Always one step ahead.
Kapsch TracCom North America | 8201 Greensboro Drive, Suite 1002 | McLean, VA 22102 | Phone +1 703 885 1976 |
Fax +1 703 790 9100
E-Mail ktc.ca.info@kapsch.net | ktc.na@kapsch.net | www.kapsch.net
801850-022 Rev A4
Loading...