Kanto YUMI POWERED SPEAKER User Manual
English
YUMI
POWERED SPEAKERS
User Manual
YUMI Powered Speakers
Supporting your digital lifestyle
™
Table of Contents
Important Safety Precautions . . . . . . . 2
Introduction / What’s in the Box? . . . . . 3
Front & Rear Panels . . . . . . . . . . . . 4
Remote Control . . . . . . . . . . . . . . 5
Setting Up Your Speakers . . . . . . . . . . 6
Connecting Audio Sources . . . . . . . . . 7
USB Charging . . . . . . . . . . . . . . . 9
Connecting a Sub-Woofer . . . . . . . . . .10
Specifications . . . . . . . . . . . . . . . . 11
Warranty . . . . . . . . . . . . . . . . . .12
Important Safety Precautions
ATTENTION
The exclamation point within an
equilateral triangle is intended to
alert the user of the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the apparatus.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
• Protect the power-supply cord from being walked on or
pinched, particularly at plugs, convenience receptacles and
the point where they exit from the apparatus.
• Only use attachments / accessories specified by the
manufacturer.
• Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE BACK PANEL.
NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
• Unplug this apparatus during lightning storms or when
• Refer all servicing to qualified service personnel. Servicing
• Apparatus shall be connected to a MAINS socket outlet with
• An appliance input coupler is used as the disconnect device
• Batteries or battery packs shall not be exposed to excessive
DANGEROUS VOLTAGE
The lightning flash with arrowhead, within an
equilateral triangle, is intended to alert the user
of the presence of non-insulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a
risk of electric shock to persons.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
unused for long periods of time.
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, the
apparatus does not operate normally, or the apparatus has
been dropped.
a protective earthing connection.
- the disconnect device shall remain readily operable.
heat such as sunshine, fire or the like.
FCC Warnings
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
FCC Notice:
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Industry Canada Notice:
• Complies with CAN ICES-3(B) / NMB-3(B)
2
Introduction
Thank you for choosing the YUMI Powered Speaker System, designed by Kanto in Canada. YUMI
outputs 30 W RMS (60 W peak) per side into 6 Ohm speakers, for remarkably bold and clean
sound. Excellent sensitivity and frequency response specs provide deep thumping lows and
clear, scintillating highs. YUMI is a truly flexible speaker system that can accept five input sources
(including optical and Bluetooth®), drive a sub-woofer, charge USB devices and switch between
115 V and 230 V inputs.
We recommend you read all instructions carefully before using the system, and keep them for
future reference. Ensure that the Voltage Select switch is set to the correct input voltage for
your location. Kanto cannot be liable for damage or injury caused by incorrect setup or use of
this product.
This powered speaker system was carefully tested and inspected during production, and before
packaging and shipping. After unpacking, please check for any damage. It is rare that a unit is
damaged during shipping, but if this happens contact your retailer immediately. You can also
call Kanto directly at 1-888-848-2643 or email support@kantospeakers.com.
What’s In the Box?
RESET
BASS TREBLE
YUMI
x2
x3
YUMI Active
Speaker
(Left Channel)
x8
Self-Adhesive
Rubber Feet
3
YUMI Passive
Speaker
(Right Channel)
Power
Cord
YUMI
Remote
Speaker
Wire (10’)
‘AAA’
Batteries
User
Manuals
RCA - 3.5 mm
‘Y’ cable (10’)
Supporting your digital lifestyle
™
Front & Rear Panels
FRONT PANEL
1 1” Silk Dome Tweeter
2 Signal LED (White) -
ON - Paired Device in Range
SLOW FLASH - Bluetooth Pairing Mode
FAST FLASH - USB Charging Mode
OFF - Bluetooth Input Not Selected
3 Power LED -
BLUE - Operating Mode
AMBER - Standby Mode
AMBER FLASHING - Mute
4 Remote Receiver
5 Volume / Input Select Knob
6 5” Kevlar Mid-Range Driver
REAR PANEL
7 Bass Reflex Port Tube
8 RCA Left and Right Input Connectors
9 3.5 mm Stereo Mini-Jack Input
Connector
10 Sub Woofer Output
11 Optical 1 and Optical 2
TOSLINK Input Connectors
12 Right Channel Output Terminals
(+ and −) for Passive Speaker
Connection
13 USB Charge Port (1 x 5V 1 A)
14 Voltage Select Switch
(115V 60 Hz / 230V 50 Hz)
15 ON/OFF Switch
16 AC Input Connection (IEC320/C14)
1
2
3
4
5
6
7
8
9
10
11
Volume/Input Select Knob
YUMI’s volume knob functions as an input
select knob as well.
Push the knob to select an input source
- it cycles through the following inputs
depending on what input source was last
used.
BLUETOOTH RCA 3.5mm OPT1 OPT2
12
13
14
15
16
4
Loading...