Kanmed Babybed User manual

User Manual

Art no: BB1-070/1
March 2007

Caution

Please read this manual carefully.
Incorrect use may cause patient injury.

Manufactured by:

KANMED AB

www.kanmed.se

Distributed by:

Contents

1 General Description .....................................................................................................3

2 Description of Symbols.................................................................................................3

3 Preparations before use................................................................................................4

4 Handling and daily use .................................................................................................5

5 Cleaning and Maintenance ............................................................................................6

6 Trouble shooting .........................................................................................................6

7 Warranty Statement ....................................................................................................6

8 Technical Data ............................................................................................................7

9 Technical service and maintenance ................................................................................8

10 Spare parts/Accessories..............................................................................................9

11 EMC guidelines ..........................................................................................................9

User Manual BB1/070/1

KANMED BABYBED
TWIN VERSION AND FIXED HEIGHT VERSION

Page 2 of 12

1 General Description

The intended use of the Kanmed Babybed is to provide an ideal bed for premature and new born babies
in hospital. It is also intended to be used with the Kanmed Babywarmer system.
It is designed for hospital use only and must be used according to the instructions given in this manual,
according to your established clinical routines and by qualified personnel. Only persons that have been
instructed in the use of the Kanmed Babybed shall be allowed to use the product.
Warning: Do not use the Kanmed Babybed with babies/small children that are capable to move so
much that they might fall/climb out of the bed.
Do not leave a baby unattended with the side walls down.
Respect the weight limits.
Do not place electronic equipment on the shelf under the bed.

2 Description of Symbols

User Manual BB1/070/1

Maximum Load permitted:
Bed surface for BB-1 and BB-3: 10 kg.
(Excl BABYWARMER Control Unit (3kg) and Water mattress (4.5kg))
Bed surface BB-4= 10 kg
(Excl Two BABYWARMER Control Unit (2x3kg) and two Water mattresses
(2x4,5kg) or one BABYWARMER Control Unit (3kg) and twin water mattress
(9kg))

Shelf under bed surface:10 kg
Top shelf: 5
25 mm Side poles to top shelf: 5 kg on each
Horizontal bars top shelf system: 10 kg
Storage box system: 10 kg

Read users manual before use

Symbol for raising and lowering the bed ( not for BB-03)

Symbol for tilt function

Fulfils MDD 93/42 EEC

~

AC current (not for BB-3)

Protection grade Type B (Body) (not for BB-3)

Approval symbol for the USA and the Canadian Markets

When the Babybed reached end of life, it should be returned to the distributor for
recycling in accordance with the EU 2002/96/EC (WEEE) directive if applicable.

Page 3 of 12

3 Preparations before use

3.1 Mounting of the Wheels

Lay down the unit carefully on its side.
Be careful not to damage the side walls.
Note that the lockable wheels shall be
mounted on the long legs.
Use the enclosed Allen key and tighten hard!
Be careful not to damage the paint.
Raise the unit to an upright position

3.2 Side Walls

If sidewalls are not mounted then please see
section Service.
Raise the sidewalls gently and slide them into
place and remove the protection film.

3.3 Tent pole, Tent and Mattress

Mount the tent pole in the rear bracket.
The Tent has a channel inside. Thread the Tent pole into the channel in order to secure it.
Place the mattress in the bed.

3.4 Check all bolts and screws

Make sure that all bolts and screws are properly tightened and that the bed
feels stable. Run the electrical bed up and down and ensure that it moves smoothly without
any unusual noise.

3.5 Kanmed Babywarmer

The Kanmed Babywarmer control unit is hung on its bracket under the bed.
The heating pad cable is preferably thread through one of the holes in the bed and connected to the
control unit. The Kanmed Babywarmer is connected to mains power by its own cable.

3.6 First cleaning

The unit is factory clean but must be cleaned according to your hospital routines.
Please refer to section maintenance for cleaning before use with the first patient.

User Manual BB1/070/1

Page 4 of 12