Kambrook KMH100 User Manual

Micathermic

Heater

KMH100

KMH100_IB_A11_FA.indd 1 14/09/11 1:58 PM

Instruction Booklet

Important

Please retain your instruction
book for future use.

In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 273 845
(New Zealand). Alternatively, visit us on our website at
www.kambrook.com.au or www.kambrook.co.nz

KMH100_IB_A11_FA.indd 2 14/09/11 1:58 PM

Contents

Kambrook Recommends p4
Safety First

Your Kambrook p6
Micathermic Heater

Quick Start Guide p7
Using Your p8

Micathermic Heater
Care, Cleaning and Storage p13

KMH100_IB_A11_FA.indd 3 14/09/11 1:58 PM

Kambrook Recommends Safety First

IMPORTANT: Please retain your
instruction book for future use.

At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.

Important Safeguards For Your Kambrook
Micathermic Heater

• Carefully read all instructions before
operating the Heater and save for
future reference.

• Remove any packaging material and
promotional stickers before using the Heater
for the first time.

• Connect only to a 230V or 240V
power point.

• Avoid touching the heater body while it is on,
as some parts of the heater are hot. When
moving the unit switch off and hold the heater
by the handles where provided.

WARNING: In order to
avoid overheating, do
not cover the heater.

• Extreme caution and supervision is necessary
when this heater is used by or near children or
invalids.

• Extreme caution and supervision is necessary
when this heater is used near animals.

• Do not mount on ceiling.

• Do not leave the heater unattended. Always
switch off the heater at the controls and at
the power outlet then unplug from the power
outlet when not in use.

• Do not use heater to dry your laundry.

• Do not operate heater whilst asleep.

• Do not operate any heater with a damaged
cord or plug, or if the heater has been dropped
or damaged in any manner. Return the heater
to your nearest Kambrook Service Centre
for examination, electrical or mechanical
adjustment or repair.

• Do not use outdoors. This heater is not
intended for commercial use, such as
construction sites.

• Do not locate the heater immediately below
and in front of a socket outlet when in use.

• Do not use this heater with an external
programmer, timer or any other device that
switches the heater on automatically. Since
a fire risk may exist if the heater is covered or
positioned incorrectly.

• This heater is not intended for use in wet or
moist locations. Do not immerse or allow liquids
to be spilt on the heater.

• Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.

• This heater has hot and arcing or sparking
parts inside. Do not use in areas where
petrol, paints, aerosols, or other inflammable
substances are used or stored.

• Do not operate the heater with the power cord
damaged, frayed or split, wound around any
part of the heater, or in contact with heated
surfaces of the heater.

4

KMH100_IB_A11_FA.indd 4 14/09/11 1:58 PM

• Do not allow materials that have been in
contact with oil, petroleum based products
or drying fluids to come in contact with the
heater.

• Do not run the cord under carpeting or cover
the cord with rugs, runners or the like. Arrange
the cord away from traffic areas and where it
will not be tripped over.

• To disconnect the heater, switch control to off,
turn off at the power outlet then remove the
plug from the outlet.

• Do not insert or allow foreign objects to pass
through the inlet or outlet openings. This may
cause an electric shock, fire or damage the
heater.

• Do not touch hot surfaces.

• Switch off at the control switch and power
outlet, then unplug and allow the heater to
cool down before cleaning or storing.

• Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacturer may
cause fire electric shock or injury and voids all
warranties.

• Keep combustible materials such as drapes
and other furnishings at least 2.0 metres from
the front and 0.5m from the sides and rear
(when it is intended for floor use) and 1.0m
from the top of the heater.

• To prevent a possible fire or heat damage,
allow ample space around the heater (at
least 2.0m at front, 1.0m at the top and 0.5m at
the rear and sides when it is intended for floor
use), (at least 2.0m at the front, 1.0m at the top
and 0.5m at the sides when it is wall mounted)
and do not totally or partially block the air inlet
or outlets in any manner. Check the openings
from time to time for accumulated dust.

Important Safeguards For All
Electrical Appliances

• Carefully read all instructions before operating
the appliance and save for future reference.

• Remove and safely discard all packaging
material and promotional labels before using
the appliance for the first time.

• Fully unwind the power cord before use.

• Do not let the power cord hang over the edge
of a bench or table, touch hot surfaces or
become knotted.

• To protect against electric shock, do not
immerse the power cord, power plug or
appliance in water or any other liquid, unless it
is recommended in the cleaning instructions.

• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance, by a person
responsible for their safety.

• Children should be supervised to ensure that
they do not play with the appliance.

• It is recommended to inspect the appliance
regularly. Do not use the appliance if the
power supply cord, plug, connector or
appliance becomes damaged in anyway.
Return the entire appliance to the nearest
authorised Kambrook Service Centre for
examination and/or repair.

• Any maintenance other than cleaning should
be performed at an authorised Kambrook
Service Centre.

• This appliance is for household use only. Do not
use this appliance for other than its intended
use. Do not use in moving vehicles or boats.
Do not use outdoors. Misuse may cause injury.

• The installation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisable that a
safety switch with a rated residual operating
current not exceeding 30mA be installed in
the electrical circuit supplying the appliance.
See your electrician for professional advice

• Always turn the appliance to the OFF
position, switch off at the power outlet
and unplug at the power outlet when the
appliance is not in use.

• Before cleaning, always turn the appliance to
the OFF position, switch off at the power outlet,
unplug at the power outlet and remove the
power cord, if detachable, from the appliance
and allow all parts to cool.

• Do not place this appliance on or near a heat
source, such as hot plate, oven or heaters.

• Position the appliance at a minimum
distance of 20cm away from walls, curtains
and other heat or steam sensitive materials
and provide adequate space above and on
all sides for air circulation.

5

KMH100_IB_A11_FA.indd 5 14/09/11 1:58 PM

Your Kambrook Micathermic Heater

1. 1500 watts of power for fast and

even heat

2. Heat setting dial for OFF, LOW

or HI

3. Variable THERMOSTAT

control to maintain your
desired temperature

4. Micathermic element

produces both radiant and
convection heat

5. Wheels for easy movement

6. Carry handle

NOT SHOWN

• Wall mountable bracket

• Safety tip-over switch

• ThermoGuard safety protection

for peace of mind

6

KMH100_IB_A11_FA.indd 6 14/09/11 1:58 PM

Quick Start Guide

Turning the
heater on after
assembly

Turn the heat
setting dial to the
off position. Make
sure that the switch
on the THERMOSTAT
dial is set to MIN.

When a
comfortable room
temperature has
been reached,
turn the variable
THERMOSTAT in
an anti-clockwise
direction until a
click sound is heard,
then stop.

Plug the cord into
a 230V or 240V
power point and
switch on.

Turning the
heater off

Return the heat
setting dial to the
OFF position to turn
off the heater.

Setting the
heating mode

Turn the heat
setting dial in a
clockwise position
to the LOW or HI
heat setting.

Setting the
variable
temperature

Turn the variable
THERMOSTAT dial in
an anti-clockwise
position to the
MAX setting.

Hints/Tips to Retain Heat in
Your Home

• Don’t overheat your home. The

temperature of a heated room in winter
should be 18-21°C

• Your heater will work more efficiently if
you stick to Kambrook’s recommended
clearance spaces

• Choose the right size heater for the room
type you want to heat

• Zone off unoccupied rooms by closing
doors and only heat the main living areas

• Fit window coverings like curtains to limit
winter heat loss

• Put draft stoppers, such as a rolled
up towel, at the bottom of outside
doorways to keep out cold air

• Keep the heat in and the
cold out by installing wall and ceiling
insulation

• Avoid placing items too close to the
heater at the front (and back if it is for
floor use) for optimal air flow

7

KMH100_IB_A11_FA.indd 7 14/09/11 1:58 PM

Using Your Micathermic Heater

Before First Use

Remove any promotional material or
packaging from the heater.

When unpacking the heater, check
to see you have received the wheels
and wall mounting packs, before
discarding the packaging.

Unwind the cord to its full length and
place the heater on a firm, level
surface in a stable upright position.
Visually inspect the air inlet and outlets
to ensure there are no blockages.

Securing The Heater Wheels

The heater has four wheels and two
wheel brackets that come with a
set of screws. The wheel screws are
located in the wheel pack.

2. Line up the screw in the wheels

with those in the base of the
brackets, and secure.

Fig. 3

3. Turn the heater upside down.

Place the plastic wheel brackets
onto the two perforations, located
at the base of the heater. Ensure
the bracket with the centre hole
(near the centre screw) is placed
on the right hand side of the
heater.

Fig. 1

1. Insert the screw into the wheel,

ensuring the flat end of the screw
sits between the wheels.

Fig. 2

8

KMH100_IB_A11_FA.indd 8 14/09/11 1:58 PM

Fig. 4

4. Line up the bracket screw with

the screw hole in the base of the
heater, and secure.

Fig. 5

Fig. 6

5. Turn the heater upright so that

the wheels are holding up the
heating unit.

Wall Mounting Instructions

Please ensure your wall is capable
of holding the weight of this heater
and that the right screws are used for
your wall.

This unit can be mounted on any wall
in most rooms of the home (except in
the immediate surroundings of a bath,
a shower or a swimming pool). When
selecting a location, decide upon a
position that takes advantage of the
maximum volume of air flow.

CAUTION: Before
mounting the heater to
the wall, please ensure
that both attachment
points are secure in either
timber or concrete. Do
NOT secure directly into
plaster. Please contact
a tradesman if you are
unsure. Please see Fig.

7. which illustrates the
points of contact. Ensure
that the heater is at least

0.5 metres from the floor
and corners of the wall.

NOTE: Ensure the feet are
removed from the unit before
wall mounting the heater.

NOTE: The heater comes with
two sets of screws and wall
mounting brackets which can
be found in the bracket pack
and on the back of the heater.

1. Locate the brackets at the back

of the heater. The bracket is
located at the top of the heater
in the centre as per fig 7.

Fig. 7

9

KMH100_IB_A11_FA.indd 9 14/09/11 1:58 PM

Using Your Micathermic Heater continued

2. As a general safety guide select

a suitable location to wall mount
the heater, approximately 0.5m
from any furniture/furnishing either
side of the unit and 2m from any
furniture/furnishing placed in front
of the heater. The heater must be
mounted horizontally as per Fig 8.

Fig. 8

3. When selecting a location, make

sure the base of the heater is at
least 0.5m from the floor and at
least 1.0m from the ceiling.

4. Measure out and mark the screw

locations. Once you are confident
that the screw locations are
correct, drill suitable size holes.

6. Once the heater is mounted

on the wall, lodge the heater
to the mounting bracket to
prevent the heater from being
accidently dislodged from the
mounting bracket.

7. Visually inspect the front panel

to ensure no foreign material is
blocking this area.

CAUTION: Do not
mount the heater below
curtains and/or other
flammable items.

Turning Your Heater On

Turn the heat setting dial to the OFF
position. Make sure that the switch on
the THERMOSTAT dial is set to MIN.

Plug the cord into a 230V or 240V
power point and switch on.

NOTE: To avoid an electrical
circuit overload, it is
recommended that no other
appliances are plugged into
the same circuit as your heater,
when it is in use.

5. Take care with inserting the screws

into the holes you have made,
and then mount the heater onto
the wall bracket.

10

KMH100_IB_A11_FA.indd 10 14/09/11 1:58 PM

Setting The Heating Mode

Fig. 9

To activate the heater, turn the heat
setting dial clockwise to the LOW or HI
setting. The heater will start operating
on the selected heat setting and
the red power indicator light will
illuminate. Use the heat setting dial to
select the desired heat setting.

LOW – Low heat setting (1000 watts)
HI – High heat setting (1500 watts)

Setting The Variable
Thermostat

The variable THERMOSTAT can be used
to maintain your desired temperature.

Turn the variable THERMOSTAT dial to
the MAX setting. Once a comfortable
room temperature has been reached,
slowly turn the variable THERMOSTAT
dial anti-clockwise until a click sound
is heard.

At this setting your heater will
automatically cycle on and off
to maintain the desired room
temperature.

Turn the heat setting dial to the OFF
position to stop the heater operating.

NOTE: This heater features a
tip-over switch. If the heater tips
over, it will automatically switch
off. Once placed back into the
upright position, the heater will
resume operation.

NOTE: You may notice a faint
smell and light crackle sound
when using the mica heater for
the first time. This is normal and
nothing to worry about. Continue
running the mica heater, the
smell will dissipates.

KMH100_IB_A11_FA.indd 11 14/09/11 1:58 PM

To adjust the set temperature turn the
variable THERMOSTAT dial clockwise
to increase the desired temperature
and anti-clockwise to decrease the
desired temperature.

Fig. 10

11

Using Your Micathermic Heater continued

ThermoGuard Overheating
Safety Device

Your heater is fitted with a safety
device that switches off the heater
in the event of overheating. Should
this heater stop working, turn off the
heater and inspect the air inlet and
outlet for blockages. Wait at least
five minutes for the protection system
to reset before attempting to restart
the heater.

If the heater fails to operate or the
safety device switches off again,
return the heater to your nearest
Kambrook service centre for
examination or repair.

12

KMH100_IB_A11_FA.indd 12 14/09/11 1:58 PM

Care, Cleaning and Storage

Ensure that the heater is switched off
and disconnected from the power
point before cleaning.

Use a clean, dry cloth to clean the
external surfaces of the heater. If
the heater has collected dust or dirt
inside the unit, have the unit cleaned
by a qualified service agent. Do not
operate the heater in this condition.

Do not attempt to open up any
parts of the heater as there are no
customer serviceable parts inside.

When not in use, store the heater
(preferably in its original box) in a
cool, clean and dry location.

13

KMH100_IB_A11_FA.indd 13 14/09/11 1:58 PM

Notes

14

KMH100_IB_A11_FA.indd 14 14/09/11 1:58 PM

Notes

15

KMH100_IB_A11_FA.indd 15 14/09/11 1:58 PM

Kambrook - Australia

Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax [phone]

www.kambrook.com.au

Kambrook - New Zealand

Private Bag 94411
Botany, Manukau
Auckland 2163
New Zealand
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax [phone]

www.kambrook.co.nz

Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue A11

KMH100_IB_A11_FA.indd 1 14/09/11 1:58 PM