Kambrook KFP100 User Manual
850W Dual Processor
Dual Food
Processor
Blender
KFP100
KFP100_FOODPROC_IB_FA.indd 1 29/5/09 4:27:53 PM
2
Carefully read all instructions before operating
the Kambrook Dual Food Processor & Blender for
the first time and save for future reference.
Remove and safely discard any packaging
material and promotional labels before using the
food processor for the first time.
To eliminate a choking hazard for young children,
remove and safely discard the protective cover
fitted to the power plug of this appliance.
Do not place the food processor near the edge
of a bench or table during operation. Ensure the
surface is level, clean and free of water and other
substances.
Do not use the food processor on a sink drain
board.
Do not place the food processor on or near a hot
gas or electric burner, or where it could touch a
heated oven.
Handle the food processor and attachments
with care – remember the blades and discs are
razor-sharp and should be kept out of the reach
of children.
Use the blade protector when storing the
processing blade.
Always ensure the food processor is completely
assembled before operating. The appliance will
not operate unless properly assembled.
Ensure the Speed Selection dial is in the ‘OFF’
position and the food processor is switched off at
the power outlet and the power cord is unplugged
before attaching the processing blade, discs or
processing lid.
Always secure the processing bowl onto the
motor base before attaching the processing blade
or discs.
•
•
•
•
•
•
•
•
•
•
•
Ensure the blender/processor lid is securely
locked in place before operating.
Before using the processor ensure that the
blender drive cover is in place.
Do not remove blender jug or processing bowl
from the motor base whilst blender/processor is
in operation.
Do not push food into the food chute with your
fingers or other utensils. Always use the food
pusher provided.
Keep fingers, hands, knives and other utensils
away from moving blades and discs.
Do not place hands or fingers into the blender
jug or the processing bowl of the food processor
unless the motor, blender blade, processing blade
and discs have come to a complete stop. Ensure
the Speed Selection dial is in the ‘OFF’ position
and the appliance is switched off at the power
outlet and the power cord is unplugged before
removing the lid from the food processor bowl or
the blender jug.
Ensure the motor and blades or discs have
completely stopped fore disassembling. Ensure
the Speed Selection Dial is in the ‘OFF’ position
and the appliance is switched off at the power
outlet and the power cord is unplugged from
the power outlet before attempting to move the
appliance, when not in use, if left unattended and
before disassembling, cleaning or storing.
Do not use attachments other than those provided
with the food processor.
Do not attempt to operate the food processor
by any method other than those described in
this booklet.
Care should be taken when removing the food
from the processing bowl by ensuring the motor
•
•
•
•
•
•
•
•
•
•
KAMBROOK SAFETY
At Kambrook, we believe that safe performance is the first priority in any consumer product
so that you, our valued customer can confidently use and trust our products. We ask that any
electrical appliance that you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
IMPORTANT SAFEGUARDS FOR YOUR KAMBROOK DUAL FOOD PROCESSOR & BLENDER
KFP100_FOODPROC_IB_FA.indd 2 29/5/09 4:27:53 PM
3
Fully unwind the power cord before use.
Do not let the power cord hang over the edge of
a bench or table, touch hot surfaces or become
knotted.
To protect against electric shock do not immerse
the power cord, power plug or motor base in
water or any other liquid.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
It is recommended to regularly inspect the
appliance. Do not use the appliance if power
cord, power plug or appliance becomes damaged
in any way. Return the entire appliance to the
nearest authorised Kambrook Service Centre for
examination and/or repair.
•
•
•
•
•
•
Any maintenance other than cleaning should be
performed at an authorised Kambrook Service
Centre.
This appliance is for household use only. Do not
use this appliance for anything other than its
intended use. Do not use in moving vehicles or
boats. Do not use outdoors. Misuse may cause
injury.
The installation of a residual current device (safety
switch is recommended to provide additional
safety protection when using electrical appliances.
It is advisable that a safety switch with a rated
residual operating current not exceeding 30mA
be installed in the electrical circuit supplying the
appliance. See your electrician for professional
advice.
•
•
•
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
and the processing blade or disc, have completely
stopped before disassembling. Ensure the Speed
Selector Dial is turned to the ‘OFF’ position, the
appliance is switched off at the power outlet and
unplugged, before removing the lid from the bowl.
The processing bowl should then be unlocked
from the motor body and the processing blade or
disc holder carefully removed before attempting
to remove the processed food.
Do not blend a dry, thick or heavy mixture for more
than 60 seconds without turning the blender/food
processor off and stirring the ingredients before
continuing to blend.
If the food processor is operated continuously for
too long, it should be allowed to rest for 25-30
minutes before recommencing.
Do not use the processor and blender at the
same time.
•
•
•
Do not process hot or boiling liquids – allow
liquids to cool before placing into the processing
bowl or the blender jug.
Do not move the food processor whilst in operation.
Do not leave the food processor unattended when
in use.
Do not place any part of the food processor in the
dishwasher or microwave oven.
Do not process thin fluids such as water, milk, stock,
juice, etc., above 500ml level in the processing bowl
as this could result in overflow. To reduce the risk
of overflow, always add drier or thicker ingredients
to the processing bowl prior to adding fluids.
Do not place anything on top of the food processor
when the lid is on, when in use and when stored
Keep the food processor clean. Follow the
cleaning instructions provided in this book.
•
•
•
•
•
•
•
KFP100_FOODPROC_IB_FA.indd 3 29/5/09 4:27:53 PM
4
•
FEATURES OF YOUR KAMBROOK DUAL FOOD PROCESSOR & BLENDER
1
2
45
6
789
10
3
1112
13
1819
20
15
14
16
17
21
22
KFP100_FOODPROC_IB_FA.indd 4 29/5/09 4:27:53 PM
5
FEATURES OF YOUR KAMBROOK DUAL FOOD PROCESSOR & BLENDER
1
Blender jug lid – ensure this is correctly in
position before activating.
2
Blender jug filler cap – for adding ingredients
whilst blending
3
Blender jug – 1.5 litre capacity, ideal for mixing
liquids (this must be correctly locked into the
blender drive or the blender will NOT operate)
4
Blender drive cover – this must be correctly in
place before using the processor, otherwise
the processor will NOT operate (see following
instructions)
5
Power control dial – a choice of 3 speeds plus
pulse for complete processing/blending control
6
Motor base - 850 watts of processing/blending
power
7
Processor bowl - extra large 1.5 litre capacity
for grating/slicing vegetables, processing foods,
mixing doughs etc.
8
Processor drive shaft
9
Food pusher with removable inner 80ml
Measuring Cup – fits the into the food chute
for safe adding of foods onto the blades and
prevents splashing when using the processing
blade
10
Processing lid and feed chute – (Processor lid
must be fitted correctly or the processor will
NOT operate)
11
Disc holder – processing discs simply lock into
place
12
Stainless steel coarse grating disc – for grating
firm cheeses, fruit and vegetables
13
Stainless steel fine grating disc – for grating
chocolate and hard cheeses such as Parmesan
14
Stainless steel chipping disc – for french fries.
Also handy for stir fried vegetables
15
Non-skid suction feet – for stability
16
Stainless steel thick slicing disc – for slicing
vegetables, chicken, meat and salami
17
Stainless steel thin slicing disc – for slicing
vegetables and fruits
18
Processing blade protective cover – for storage
when blade is not in use.
19
Spatula
20
Stainless steel processing blade – use for all
chopping, mixing and processing tasks
21
Mixing blade – use for making dough for pastry
or bread
22
Unique storage holder – conveniently and safely
stores attachments on top of lid
23
Automatic safety cut out – prevents the Dual
Food Processor & Blender from operating
unless the processor bowl and lid, blender jug
or blender drive cover are correctly engaged on
the motor base (not shown)
24
Cord storage (not shown)
B
LADES MUST BE HANDLED CAREFULLY AS THEY ARE
SHARP!
KFP100_FOODPROC_IB_FA.indd 5 29/5/09 4:27:54 PM
6
USING YOUR KAMBROOK DUAL
FOOD PROCESSOR & BLENDER
Before first use remove and safely discard any
promotional labels and wash the blender jug, food
processor bowl and all blades in warm, soapy water.
Dry thoroughly.
ALL BLADES MUST BE HANDLED CAREFULLY AS THEY ARE
SHARP!
Place the motor base on a level, flat surface.
ASSEMBLY AND OPERATION OF THE
FOOD PROCESSOR
Your Dual Food Processor & Blender features 3
safety locking devices.
NOTE: THE FOOD PROCESSOR WILL NOT WORK
UNLESS ALL OF THE BELOW ARE IN PLACE:
The blender drive cover is correctly LOCKED into
position
The processor bowl is correctly LOCKED into
position
The processor lid is correctly LOCKED into position
NOTE: Always ensure that the Dual Food Processor
& Blender is disconnected from the power outlet and
operating dial is turned to ‘0’ before assembling or
disassembling the Dual Food Processor & Blender.
Correct locking procedure of the
Blender Drive Cover
Place cover over drive with the arrow on the
drive cover aligned to the align arrow
on the
motor cover. Turn clockwise until the arrow on the
drive cover is aligned with lock arrow
on the
motor cover.
Note the food processor will not operate unless the
blender drive cover is locked in the correct position
1.
2.
3.
Correct placement of the Processor
Bowl
Place the empty bowl onto the base, with the handle
on your right align the arrow
on the processor
bowl handle with the align arrow
on the
motor base. Turn the bowl clockwise until the arrow
on the processor bowl handle is aligned with the
‘lock’ indicator arrow
on the motor base.
KFP100_FOODPROC_IB_FA.indd 6 29/5/09 4:27:57 PM
7
USING THE PROCESSING BLADE/
DISCS
ALL BLADES MUST BE HANDLED CAREFULLY AS THEY ARE
SHARP! USING THE PROCESSING/MIXING BLADE
Select either the processing or plastic mixing
blade
Place the processing /mixing blade over the drive
shaft and push down.
Using the slicing/grating discs.
Select the desired slicing/grating disc and
assemble into the disc holder. To fit the stainless
steel disc onto disc holder, fit left side of disc
(when writing is towards you), with locating tab
into holder, then push right side down firmly until
it locks into place. Fit the end without the push
up marking in first. Then push the “push up” side
down firmly until it locks into place.
a.
b.
a.
To remove disc, hold disk away and place thumbs
underneath disc at top of disc marked “push up”
and push out. The disc may be tight for the first
few times.
Correct placement of the processor lid
Place the lid on top of the bowl, align the indicator
line on the lid with the circle on the bowl.
b.
Push down
Locate tab
KFP100_FOODPROC_IB_FA.indd 7 29/5/09 4:27:59 PM
8
Turn the lid clockwise – moving the ‘lid locking tab’
into the slot near the top of the motor unit - until the
indicator line on the lid is aligned with the circle
on the top of the bowl. A “click” sound will be heard,
to indicate is correctly fitted.
NOTE: The Dual Food Processor & Blender will not
operate unless the processing bowl, lid and blender
drive cover are correctly locked into position.
Ensure the speed dial is in the ‘OFF’ position.
Insert power plug into a 230/240 volt power outlet.
Turn power on.
The processor is now ready to use.
To begin processing/slicing/grating turn the ‘Power
Control Dial’ from the ‘OFF’ position to either
the Low, Medium or High speed, depending your
requirements. The speed can be changed at any
time during the process.
For short bursts of power, whilst processing, use the
“PULSE” setting.
For slicing and grating – ensure that the food
items you want to slice or grate are of a suitable
size to be feed through the food chute.
Place the food inside chute and push down with the
‘food pusher’.
NOTE! : Never push down any foods with your hands
and do not put your hands down the food chute at
any time during processing.
For using the processing blade – with the
ingredients inside the processor bowl, start the
unit on low speed moving to high if necessary.
Before commencing ensure that the ‘food pusher’
is in place to avoid splashing from the food chute.
Ingredients can be added through the food chute
whilst processing.
If ingredients stick to the sides of the processor
bowl during processing, turn the speed to the ‘OFF’
position, switch off at the power outlet, remove lid
and then push the food back onto the blades using
the plastic spatula to scrape down the sides of the
bowl. Then recommence processing.
NOTE: Do not over fill the processor bowl past the
MAX line for solids and past the 750ml mark for
liquids. For greater quantities of liquids the blender
jug should be used.
When processing is complete, turn to the ‘OFF’
position. Wait until blades have stopped rotating
before removing the lid, blades or processor bowl.
ASSEMBLY AND OPERATION OF THE
BLENDER
Your Dual Food Processor & Blender features 2
safety locking devices.
NOTE: the blender will not operate unless:
The blender jug is correctly positioned and
LOCKED onto the motor base
The processor bowl AND lid are correctly locked
into place (refer to previous instructions)
NOTE: The food processor will not operate while
the blender jug is assembled to base. If processing
is required, remove the blender and fit the Blender
Drive Cover.
1.
2.
✓
Lid
locking
tab
Insert slot
KFP100_FOODPROC_IB_FA.indd 8 29/5/09 4:27:59 PM