KAM iLink RGY, Kam iLink GBC, Kam iLink RBP, Kam iLink Blue 500 Instruction Manual

MADE IN CHINA

Kam iLink RGY | Kam iLink GBC | Kam iLink RBP | Kam iLink Blue 500

Due to continuous product development, please ensure that you have downloaded

the latest instruction manual for this product from the Kam website at www.kam.co.uk

MANUAL VERSION 1.0

01- 02- 12

For the latest updates and information on the entire Kam range visit:

www.kam.co.uk

Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ

Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [e-mail] • Web: www.lambaplc.com

Due to continuous product development, specifications and appearance are subject to change. © Copyright Lamba plc 2012. E&OE.

iLink laser series

Linkable colour DMX laser effects

Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.

To optimise the performance of this product, please read these operating instructions carefully to familiarise
yourself with the basic operations of this unit. Please retain them for future reference.This unit has been tested at
the factory before being shipped to you. To prevent or reduce the risk of electrical shock or fire, do not expose the
unit to rain or moisture. To prevent a fire hazard, do not expose the unit to any naked flame sources. Unplug this
apparatus during lightning storms or if it is unlikely to be used for long periods of time.

When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings
in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating.
To prevent fire hazard, the openings should never be blocked or covered.

If the unit is powered by the mains, always handle the power cable by the plug. Never pull out the plug by pulling
on the cable. Never touch the power cable when your hands are wet as this could cause an electric shock. Do not
tie a knot in the cable. The power cable should be placed such that it is not likely to be stepped on. A damaged
power cable can cause a fire or give you an electrical shock. Check the power cord periodicaly, if you ever find that
it is damaged, replace it before using the unit again. Contact your retailer for a replacement.

The voltage of the available power supply differs according to country or region. Be sure that the power supply
voltage of the area where this unit is to be used meets the required written on the unit.

The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the
unit’s enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts
inside. Refer all servicing to qualified service personnel.

The exclamation mark inside a triangle is intended to alert the user to the presence of important operating
and maintenance instructions in the literature accompanying the appliance.

Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to
vibration and excessive dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or
exceeding 95ºF / 35ºC).

Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect
condition. Please check that no damage has occurred during transit. If any damage is found, do not operate your
unit. Please contact the retailer you purchased it from immediately. If there is any damage to the mains cable do
not use the device. Always disconnect the unit from the mains supply when carrying out any cleaning of the unit.

Manufacturer declarations

In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU),
and Battery Directive (2006/66/EU). If this product is ever no longer functional please take it to a recycling plant
for environmentally friendly disposal. Any supplied batteries can also be recycled.

CE declaration of conformity

Low Voltage Directive (2006/95/EU). The declarations are available on application from
[e-mail]
Before putting the devices into operation, please observe the respective country-specific regulations.

Warning
This unit contains high power laser devices. Do not open the laser housing due to potential exposure to
unsafe levels of laser radiation

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.

Front and rear panels

1 Power LED Indicates that the fixture is switched on
2 Music LED Synchronises to any detected music/sound signal
3 Remote receiver Remote controller signal receiver
4 Power switch Use to power On or Off the unit
5 Fuse holder The replaceable fuse is held here
6 Mains power Power input With IEC socket and integrated fuse holder
7 DMX In/Out 3 pin male/female XLR connector
8 Key switch Insert the supplied safety key before being able to turn the laser On or Off
9 Safety eyelet Used to attach a safety cable/chain when the fixture is rigged
10 Control panel LED display and operation control buttons
12 Microphone Used to detect the music/sound signal