Page 1
Due to continuous product development, please ensure that you have downloaded
the latest instruction manual for this product from the Kam website at www.kam.co.uk
MANUAL VERSION 1.0
25- 11- 11
For the latest updates and information on the entire Kam range visit:
www.kam.co.uk
Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ
Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: mail@lambaplc.com • Web: www.lambaplc.com
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
Due to continuous product development, specifications and appearance are subject to change. © Copyright Lamba plc 2011. E&OE.
Gobolaser 550RB
Red & blue burst grating shutter FX laser
Page 2
Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.
To optimise the performance of this product, please read these operating instructions carefully to familiarise
yourself with the basic operations of this unit. Please retain them for future reference.This unit has been tested at
the factory before being shipped to you.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire
hazard, do not expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is
unlikely to be used for long periods of time.
When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings
in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating.
To prevent fire hazard, the openings should never be blocked or covered.
Always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power
cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power
cable should be placed such that it is not likely to be stepped on. A damaged power cable can cause a fire or give
you an electrical shock. Checkthe power cord periodicaly, if you ever find that it is damaged, replace it before
using the unit again. Contact your retailer for a replacement.
The voltage of the available power supply differs according to country or region. Be sure that the power supply
voltage of the area where this unit is to be used meets the required written on the unit.
The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the
unit’s enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts
inside. Refer all servicing to qualified service personnel.
The exclamation mark inside a triangle is intended to alert the user to the presence of important operating
and maintenance instructions in the literature accompanying the appliance.
Do not aim this laser directly into an audience and ensure any part of the lowest scanned beam is above
head height (ideally greater than 3m). Visible and invisible laser-light, direct beam will damage the human
eye and the eyes of animals. Do not look at any Laser light directly.
Do not touch the laser aperture with the hand. When cleaning the laser aperture, please use a soft cloth
with alcohol or camera lens paper.
Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to
vibration and excessive dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or
exceeding 95ºF / 35ºC).
Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect
condition. Please check that no damage has occurred during transit. If any damage is found, do not operate your
unit. Please contact the retailer you purchased it from immediately. If there is any damage to the mains cable do
not use the device. Always disconnect the unit from the mains supply when carrying out any cleaning of the unit.
Page 3
Front & rear panel guide
1. Laser aperture
2. Sound sensitivity adjustment
3. Built-in microphone
4. Power LED
5. Mains power input
6. On/Off power switch
7. Sound mode / Auto mode selector switch
8. Sound sensitivity adjustment
9. Safety key lock
Package contents
Laser unit, mains lead, safety key, instruction manual, laser safety guide
Page 4
Operation
1. Plug the unit into a suitable mains power supply.
2. Turn the On/Off power switch to the ON position.
3. Ensure that the key is located in the safety key lock.
4. Ensure the safety key lock is turned to the ON position.
5. Select desired function mode using the selector switch (7).
6. If using Sound-to-Light mode, ensure that the sound sensitivity is turned up and a sound source is playing.
Sound mode / Auto mode
Using the selector switch on the rear panel, select the function mode required.
In the AUTO MODE position the unit will run through it’s built-in programs at a pre-determined program speed.
In the SOUND MODE position the unit will run through it’s built-in programs in sync with the beat of the music.
Adjust the Sound Sensitivity knob on the rear panel to increase or decrease the sound sensitivity of the unit.
Anti clockwise will reduce the sensitivity and clockwise will increase the sensitivity.
Product features
Red & blue burst grating shutter FX laser
Plug&Play operation
Automatic mode
Sound-to-Light mode
LED power indicator
Built-in microphone
Sound sensitivity adjustment
Adjustable metal hanging bracket
Robust metal chassis
Safety key On/Off lock
IEC mains input
Technical specifications
Laser power: 350mW blue laser@447nm / 200mW red laser@650nm
Scanner motor: Micro stepper motor
Modes: Sound-to-Light mode / Auto mode
Input power: AC100~240V / 50~60Hz
Power consumption: 30W
Packing size LxWxH: 275x183x148mm
Weight: 2.3Kg
Class 3B laser. Visible or invisible radiation, avoid eye or skin exposure to direct or scattered radiation.
Please note this unit is designed for indoor use only
Loading...