KAM DMX STAR CLUSTER Instruction Manual

instruction manual
www.kam.co.uk
Maintenance
It is very important to keep the DMX CLUSTER laser light clean, therefore please keep the reflector lens clean. We suggest that clean the light with professional glass cleaning lotion and a soft cloth.
Due to continuous product development, specifications and appearance are subject to change. E&O E.
LASER DMX STAR CLUSTER
Cluster_manual 24/10/07 09:11 Page 1
INTRODUCTION
Thank you for purchasing the DMX CLUSTER To optimize the performance of this product, prior to use, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. DMX CLUSTER has the KAM funky design and is an amazing Laser effect. Please keep these user instructions in safe place for future reference. This unit has been Tested at the factory before being shipped to you. There is no Assembly required.
WARNING!
To prevent or reduce the risk of electrical shock or fire, do not expose this unit to high Temperature / rain or moisture.
Laser Class 3B product. National Regulations must be adhered to at all steps of installation.
(In Germany apply DIN 56912 and BGVR LASER note: additional Regulations may apply).
Unintended reflections of the laser beam from reflective or metallic surfaces can be dangerous.
This appliance is to used by Qualified personnel only.
Laser Radiation Warning
This unit uses diode lasers in green and red colour. This is CLASS 3B laser product. Avoid exposure to eyes. Never open the laser diode box, please refer unit to a qualified engineer for servicing or repair
THE DMX CLUSTER
Laser beam ef
fect. Has an Abundance of laser patterns single colour, double colour or three colours. With more than 200 Red and green laser points, the reflection angle is appr
oximately 70 degr
ees.
Package list:
When you unpack the laser, please check contents
LASER x1 MAINS LEAD x 1 USER MANUAL x1
Control mode: music control or DMX-512 signal
control, master and slave,
Cool system: fan Operating environment: indoor use only
DMX-512 function
The DMX CLUSTER laser uses DMX-512 signal. It has 5 control channels. The details of DMX-512 signal control mode address switch as follow:
Dmx cables Male xlr to female xlr Wiring is Pin 1 ground Pin 2 hot Pin 3 negative
Please check the unit for any damage which may have been caused in transit, if any damage is found DO NOT operate the unit, please contact the dealer you purchased the unit from immediately
SPECIFICATION
Solid metal construction The DMX CLUSTER laser uses two colours of laser The laser Wavelength of 532nm laser emerald green colour and 650nm°, red colour. Laser diode A double-temperature -controlled power supply. The laser light source has a long life span and high stability, complying with international standards. Built in laser blackout function, when no sound is heard the laser will enter blackout mode after 15 seconds DMX-512 signal control and music control, master and slave,
DMX CONNECTION
DMX INPUT: DMX signal input - Male XLR DMX OUTPUT: DMX signal output - Female XLR MIC: Sound active Min-Max: Adjust the sensitivity knob for sound
active
POWER SWITCH: ON/OFF power FUSE: 3A Fuse
INSTRUCTIONS
Please ensure when mounting the laser that it is fixed to a suitable structure, capable of holding the weight of the unit and fit a safety chain from the light unit to the frame work Hang the projector and adjust its angle properly, then connect to the mains supply. Please not this unit must be earthed. ensure the correct voltage is being used this unit operates on 240v ac
TECHNICAL
Rated voltage: 240V ac Rated frequency: 50HZ Power consumption: ≤15w Laser wavelength: 25-120mW/532nm,
100mW/650nm Laser source: solid semi-conductor laser generator Colour: emerald gr
een, r
ed
Dmx channels: 5
If using 5 pin xlr follow wiring instructions below
When using a dmx controller to operate several units, each unit will need to have a separate head address.
The address of the first unit is set as 1, the second unit has also 5 channels, so its address code is 6, the third unit is set at 11, so on and so forth (the setting method will also depend on the specific controller, the above is just for general cases).
Please note about master and slave When using master and slave mode, control from a dmx controller is not available Only two heads can be linked in master and slave mode.
Cluster_manual 24/10/07 09:11 Page 2
Loading...