KAM Partybar Eco, Cluster FX-Bar Instruction Manual

XY Laser

Pan & tilt scanning colour laser

MANUAL VERSION 1.0

01- 06- 16

For the latest instruction manual updates and information on the entire Kam range visit:

www.kam.co.uk

Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ

Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [e-mail] • Web: www.lambaplc.com

If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.

Due to continuous product development, specifications and appearance are subject to change.

© Copyright Lamba plc. E&OE.

Kam Partybar Eco

Portable performance lighting rig

Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.

To optimise it’s performance, please read these instructions carefully to familiarise yourself with the basic operations of the unit. Please retain
them for future reference.This unit has been tested at the factory before being shipped to you. To prevent or reduce the risk of electrical shock
or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not expose the unit to any naked flame sources. Unplug this
apparatus during lightning storms or if it is unlikely to be used for long periods of time.

When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are provided for
ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the openings should never be
blocked or covered.

The unit is powered by the mains, always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the
power cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed
such that it is not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check the power cord
periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact your retailer for a replacement. The voltage of the
available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit is to be used
meets the requirements of the unit.

The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit’s enclosure that may be of
sufficient power to constitute a risk of electrical shock to persons. Caution: to prevent the risk of electric shock, do not attempt to
open the unit. No user-serviceable parts inside. Refer all servicing to qualified service personnel. The exclamation mark inside a
triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature
accompanying the appliance.

Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive dust. Do not
use the unit where there are extremes in temperature (- 20ºC to 40ºC).

Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect condition. Please check that
no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you purchased it from
immediately. Always disconnect the unit from the mains when carrying out any cleaning of the unit.

Manufacturer declarations

In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU).
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.

CE declaration of conformity

R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU), Low Voltage Directive (2006/95/EU).
The declarations are available on application from [e-mail]
Before putting the devices into operation, please observe the respective country-specific regulations.

The unit is supplied with a power plug appropriate to its voltage. Should any other connections be required they must be carried out with the
following configuration:

Cable (EU)

Cable (US)

Pin

International

Brown

Black

Live

L

Light blue

White

Neutral

N

Yellow/green

Green

Earth

DMX-512 connection

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX
chain. If you wish to connect a DMX controller with other XLR outputs you will need to use adapter cables.
1 = Shield
DMX output 2 = Signal (-) DMX input
3 = Signal (+)

Connect the DMX output of the first unit in a DMX chain with the DMX input of the next unit in the chain. Always connect the output of one unit
with the input of the next unit until all units are connected.