KAM LASERSCAN 1000 3D, 1000/1200RGB Instruction Manual

LASERSCAN 1000 3D

Exceptional 3D ILDA laser with 5 different effects in a single unit

For the latest instruction manual updates and information on the entire Kam range visit:

www.kam.co.uk

Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ

Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [e-mail] • Web: www.lambaplc.com

If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.

Due to continuous product development, specifications and appearance are subject to change.

© Copyright Lamba plc 2010. E&OE.

Due to continuous product development, please ensure that you have downloaded

the latest instruction manual for this product from the Kam website at www.kam.co.uk

M A N U A L V E R S I O N 1 . 0

1 0 / 0 4 / 1 2

Thank you for purchasing this KAM product, we are sure that it will serve you for many years to come.

To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself with the basic
operations of this unit. After you have read the instructions, please retain them for future reference.

This unit has been tested at the factory before being shipped to you.

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not
expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long
periods of time.

When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are
provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the
openings should never be blocked or covered.

Always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power cable when your
hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed such that it is
not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check
the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact your retailer for a
replacement.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area
where this unit is to be used meets the required written on the unit.

The lightning flash symbol inside a triangle is intended to alert the user to the presence high voltage within the unit’s

enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.

Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.

The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.

Any modification carried out on the unit may invalidate the unit’s warranty.

If applicable, only use the stand, tripod or bracket specified or sold with the apparatus.

Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive
dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding 95ºF / 35ºC).

Unpacking and safety: Please unpack your new product carefully, your new product should reach you in perfect condition. Please
check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you
purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from
the mains supply when carrying out any servicing or cleaning of the unit.

The serial number for this equipment should be located on the rear or underside of the unit. Please make a note of this number as
you will need it for your warranty, it is a good idea to keep a copy of the serial number for your own records.

Unpacking instructions

CAUTION! Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present
and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts
appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the
event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Contents

1 x Laser, 2 x Keys, 1 x Interlock connector and 1 x Power cord.

Power Supply

Cable (EU)

Cable (US)

Pin

International

Brown

Black

Live

L

Light Blue

White

Neutral

N

Yellow/Green

Green

Earth

DMX-512 connection between fixtures

The fixture is equipped with 3-pin XLR sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted-pair cable designed for 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with
another.

XLR-connection

Building a serial DMX-chain

 If you are using a standard DMX-controller, you can connect the DMX-output of the controller directly with the DMX-input of

the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter
cables. (DMX controller not supplied).

 Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect output

with the input of the next fixture until all fixtures are connected.

 If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pins adapter.
 The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is disconnected to the unit.
 Each fixture needs to have a DMX address to receive the data from the controller. The DMX address number which could be

read from rear panel of each fixture is between 000~511.