Kalorik USK BL 3-4-5 User Manual

Blender

Batidora de Vaso

Blender

USK BL 3/4/5

120V~60Hz 500W



IMPORTANT SAFEGUARDS

1. READ ALL INSTRUCTIONS

2. Check that your mains voltage corresponds to that stated on the
rating plate of the appliance before using the appliance.

3. To protect against electrical shock do not immerse cord, plug, or
the motor unit in water or other liquid.

4. Close supervision is necessary when the appliance is used by or
near children.

5. Unplug from outlet when not in use and before putting on or
taking off parts or before cleaning.

6. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair, or adjustment.

7. The use of accessory attachments, including the pouring jar, not
recommended by the appliance manufacturer may cause
injuries.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter or touch hot
surfaces.

10. Do not place on or near a hot gas or electric burner, or in a
heated oven.

11. Always attach plug to appliance first, then plug cord into the wall
outlet. To disconnect remove the plug from the wall outlet.

12. Do not use appliance for other than intended use.

13. This kind of appliance cannot function continuously, it is not a
professional type of appliance. It is necessary to make temporary
stops. Check the section "Important information" in the
instruction manual.

14. It is absolutely necessary to keep this appliance clean at all times
as it comes into direct contact with food.

15. The pouring jar should be assembled correctly on the motor base
before you plug it into the mains. The appliance is equipped with

2

USK BL 3/4/5 - 060405

a safety, which prevents the pouring jar from working if it is not
assembled correctly.

16. The appliance is designed for the preparation of small quantities
of food, which have to be consumed rather quickly. It is not
designed for the preparation of large quantities at once.

17. Keep hands and utensils out of container while blending to
reduce the risk of severe personal injury and/or damage to
blender. A rubber spatula may be used but must be used only
when blender is not running.

18. Do not use a broken, chipped or cracked blender jar.

19. To reduce the risk of injury, never place the cutting unit blades on
base without jar properly attached.

20. Blades are sharp, handle with care.

21. Always operate the blender with cover in place.

22. Always close the jar with the lid before starting mixing. When
mixing hot liquid, do not fill more than 2/3 of the jar and be very
careful in order to avoid splashing of hot liquid, otherwise you can
get burned. Do not forget to close the feeding hole of the
pouring jar with the cap.

23. Screw on blade assembly firmly. Injury can result if moving blades
accidentally become exposed.

24. Do not leave blender unattended while it is operating.

25. To disconnect cord, turn the speed selector to "0" , then remove
the plug from wall outlet.

SAVE THESE INSTRUCTIONS

POLARIZED PLUG INSTRUCTIONS

This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug will fit into the
polarized outlet only one way. If the plug does not properly fit into
the outlet at first, reverse it. If it still does not fit, contact a competent
qualified electrician. Do not attempt to modify the plug in any way.

3

USK BL 3/4/5 - 060405

SHORT CORD INSTRUCTIONS

A short power supply cord is provided to reduce the hazards resulting
from becoming entangled in, or tripping over a longer cord.
Extension cords may be used if care is exercised in their use.

• The electrical rating of the extension cord should be at least

that of the appliance. If the electrical rating of the extension
cord is too low, it could overheat and burn.

• The resulting extended cord should be arranged so that it will

not drape over the counter top or tabletop where it can be
pulled on by children or tripped over.

PART DESCRIPTION

1. Locking cap with feeding

opening

2. Lid

3. Mixing jar

4. Sealing ring

5. Blades

6. Blade fixing ring

7. Motor block

8. Switch (P / 0 / 1 /2)

9. Jar assembly

4

USK BL 3/4/5 - 060405

IMPORTANT INFORMATION

This appliance is not for professional use. You should follow the
requested breaks. Failure to follow this instruction carefully may result
in damage to the motor. The maximum continuous usage time is 1
minute. After 1 minute of continuous use, you should insert a break of
at least 10 minutes.

ASSEMBLY OF THE BLENDER AND USE

CAUTION!

Your appliance is fitted with a security device allowing the
functioning of the appliance only when the jar is correctly placed on
the motor block. If the jar is correctly positioned and the appliance
does not start, call your after sales service.

If the blade is disassembled from the bottom of the jar, check the
cleaning section for mounting instructions before continuing.

• Put pouring jar on the motor block and make sure it is correctly
inserted.

• Remove the lid of the blender.

• Fill the pouring jar with the chosen ingredients.

• Close the lid.

• Plug in the appliance.

• Choose the mixing speed with the button on the motor base. The

position 0 corresponds to the stopping of the appliance, the
position 1 to the slow speed and the position 2 to the fast one.

• The position "P" (Pulse) is particular because the button has to be
kept manually. This position is generally used to crush ice in order
to avoid damages on the blades, but it can also be used to
complete the mixing.

• It is also possible to add liquids or other ingredients anytime
without stopping the appliance. You only have to remove the
cap, which closes the feeding opening by turning and raising it
straight up.

• Once you have finished the preparation, stop the appliance
(position 0) and unplug the appliance.

5

USK BL 3/4/5 - 060405

• Remove the jar from the base. Then remove the lid and pour the
liquid in the desired receptacle.

HOW TO CLEAN

• Always unplug from outlet before cleaning.

• For a quick rinsing of the pouring jar (for example between two

preparations), you can use clear water and switch on your
appliance for a few seconds. In this case, do not use any
detergent.

• For a full cleaning, remove the jar from the motor block and turn
the blade fixing ring on the bottom of the jar anti-clockwise to
detach the sealing ring and the blade (this will make the
cleaning easier). Then you can clean these parts with soapy
water and rinse thoroughly with clear water. Dry before
assembling. To attach the blades, put the sealing ring around the
blades, insert them in the bottom of the jar and tighten the fixing
ring by turning it clockwise (tighten vigorously in order to avoid
leaks). Caution, do not lose the seal during this operation.

• You can wipe the motor block with a soft damp cloth.

6

USK BL 3/4/5 - 060405