Kalorik JK 39380 User Manual



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change

Glass Water kettle

Hervidor con jarra
de cristal

Bouilloire électrique
en verre

the page numbering. Keep the language integrity. Print only

what is inside the frame.

JK 39380

www.KALORIK.com

120V~60Hz 1500W (12.5A)



Front cover page (first page)

Assembly page 1/24



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed, including the following:

1. READ ALL INSTRUCTIONS

2. Check that the voltage in your home corresponds to that stated
on the rating label of the appliance.

3. Do not touch hot surfaces. Use handles or knobs.

4. To protect against electrical shock do not immerse base, cord,
plug, or the jug kettle in water or other liquids.

5. Close supervision is necessary when any appliance is used by or
near children.

6. Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts.

7. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair, or adjustment.

8. The use of accessory attachments not recommended by the
appliance manufacturer may cause injuries.

9. Do not use outdoors.

10. Do not let cord hang over edge of table or counter, or touch hot
surfaces.

11. Do not place on or near a hot gas or electric burner, or in a
heated oven.

12. Always attach plug to appliance first, then plug cord into the wall
outlet. To disconnect, put the switch in off position, then remove
plug from wall outlet.

13. Do not use appliance for other than intended use.

14. Scalding may occur if the lid of the jug kettle is removed during
the heating cycles.

15. Make sure the appliance never comes into contact with
inflammable materials such as curtains, textiles ..., when it is in use
as they might catch fire.

16. When removing mineral deposit, only use special products
formulated for the removal of mineral deposit (decalcifying

2

Assembly page 2/24

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

solutions). Never use ammonia or any other substance that might
damage your health.

17. Do NOT use abrasive cleaners to clean the inside or outside of the
kettle, to avoid permanent damage to the surface.

18. Ensure that the kettle is properly positioned on the power base
before switching on.

19. Do NOT refill with water while the appliance is switched on.

20. Remove the kettle from power base before filling or pouring. If the
base becomes wet, unplug the kettle from the power outlet and
switch off. After it has become dry, you may replace the kettle on
the base, after ensuring that the kettle is switched off.

21. Use the kettle only with the power base supplied and vice versa.

22. Use on a hard, flat level surface only.

23. If the kettle is overfilled, boiling water may be ejected.

24. Extreme caution must be used when handling or moving kettle
and pouring from the kettle containing boiling water.

25. Make sure that the lid and the filter are correctly and securely
fitted before switching on the appliance. Failure to do so will
cause the kettle not to switch off, and boiling water might eject
through the spout causing scalding or injuries.

26. When pouring a large quantity of hot water, pour slowly and do
not incline the kettle past the horizontal line to avoid burns and
injuries.

27. When you are done using the appliance, switch it off and unplug
the power cord from the wall socket.

28. NEVER use the appliance to boil anything other than water.

29. NEVER use near a flame or hot surface.

30. NEVER put any part of the hand or body near the appliance
when switched on. Steam is invisible and will cause scalding or
injury.

31. NEVER use the appliance if it has been dropped on the floor or
damaged in any way.

SAVE THESE INSTRUCTIONS

HOUSEHOLD USE ONLY

3

Assembly page 3/24

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

3

5

9

7

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

POLARIZED PLUG INSTRUCTIONS

This appliance is equipped with a polarized plug (one blade is wider
than the other). To reduce the risk of electric shock, this plug will fit
into the polarized outlet only one way. If the plug does not properly
fit into the outlet at first, reverse it. If it still does not fit, contact a
competent qualified electrician. Do not attempt to modify the plug in

any way.

SHORT CORD INSTRUCTIONS

A short power supply cord is provided to reduce the hazards resulting
from becoming entangled in, or tripping over a longer cord.
Extension cords may be used if care is exercised in their use.

• The extension cord should be a grounding type 3-wire cord.

• The electrical rating of the extension cord should be at least

that of the appliance. If the electrical rating of the extension
cord is too low, it could overheat and burn.

• The resulting extended cord should be arranged so that it will

not drape over the counter top or tabletop where it can be
pulled on by children or tripped over.

PART DESCRIPTION

1. Power base

2. Power switch

3. Handle

4. Lid opening button

5. Lid

6. Spout with scale filter

7. Glass housing

8. Illumination LED ring

9. Cord storage in base

4

6

8

Assembly page 4/24

4

2

1

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

BEFORE THE FIRST OPERATION

For the perfect taste, operate the cordless water kettle with fresh
water in order to clean any residue left from the manufacturing
process. When the appliance has cooled down, repeat the process
3 times with fresh water, before rinsing.

OPERATION

•

Always remove the kettle from the power base (1) before filling it
or before any operation.

•

Open the lid (5) by pressing on the lid opening button (4) and fill
the tank with fresh water, paying attention not to fill under the
minimum mark or above the maximum mark indicated on the
glass housing of the kettle (7).

•

Close the lid by pressing it down until it you hear a click. Make
sure it closes correctly.

•

Make sure the spout filter is well in position, as else the auto-shut
off feature might not work.

•

Put the kettle onto the power base (1), plug into the wall socket,
and switch on (2). The blue light ring (8) will come on, indicating
that the appliance is operating. If it does not come on, check if
the kettle is correctly positioned on the base and check if the
base is plugged in. Do not open the lid while the water is heating
or boiling.

•

The cordless water kettle will switch off automatically when the
water has boiled. However, you can stop the appliance anytime
by putting the switch in off position or lifting the kettle from the
power base.

CAUTION: Make sure that the lid is closed and the filter is correctly
and securely fitted before switching on the appliance. Failure to do
so will cause the kettle not to switch off.

• For instant re-boiling, wait until water has cooled down and
switch on the appliance again.

• The kettle will not re-boil until the switch is pressed again.

• The kettle may be stored on the power base when not in use.

• Always disconnect the power supply when not in use.

5

Assembly page 5/24

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

• When pouring a large quantity of hot water, pour slowly and do
not incline the kettle past the horizontal line to avoid burns and
injuries.

SAFETY CUT-OUT

•

This cordless water kettle is protected with an automatic safety
device, if accidentally switched on without water. Please bear in
mind that only the thermostat is switched off in case of overheat,
whereas the switch stays in the ON-position.

•

If this happens, switch off the appliance by putting the switch in
the OFF position and wait about 10 minutes for the element to
cool. Then pour in sufficient cold water to cover the element. This
will reset the safety device.

•

The kettle may then be used as normal.

CLEANING AND MAINTENANCE

•

Before attempting any cleaning operation, make sure the
appliance is unplugged from the supply socket and fully cooled
down.

•

To clean the exterior surfaces, simply wipe over with a soft, damp
cloth and dry thoroughly.

•

Never use abrasive products, powders or scouring pads.

•

Under no circumstances shall the jug kettle or its power base be
immersed in water.

•

To remove mineral deposits from the water kettle, use products
(decalcifying solutions) made especially available for this
purpose. Make sure to use a type recommended for kettles or
coffee makers. Follow the guidelines as recommended by the
manufacturer of the de-calcifying solution. Rinse well.

FILTER

• Your appliance is provided with a mesh filter. This filter is factory
pre-installed before the spout.

• The filter is placed in front of the spout. Filter should be rinsed
clean regularly. For this, press the filter out, rinse under water, and
put it back into position once clean.

6

Assembly page 6/24

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

WARRANTY

We suggest that you complete and return the enclosed Product
Registration Card promptly to facilitate verification of the date of
original purchase. However, return of the Product Registration Card is
not a condition of these warranties. You can also fill out this warranty
card online, at the following address: www.KALORIK.com

This KALORIK product is warranted in the U.S.A. for 1 year from the
date of purchase against defects in material and workmanship. This
warranty is not transferable. Keep the original sales receipt. Proof of
purchase is required to obtain warranty performance.

During this period, if the KALORIK product, upon inspection by
KALORIK, is proven defective, it will be repaired or replaced, at
Kalorik’s option, without charge to the customer. If a replacement
product is sent, it will carry the remaining warranty of the original
product.

This warranty does not apply to any defect arising from a buyer's or
user's misuse of the product, negligence, failure to follow KALORIK
instructions noted in the user’s manual, use on current or voltage
other than that stamped on the product, wear and tear, alteration
or repair not authorized by KALORIK, or use for commercial purposes.
There is no warranty for glass parts, glass containers, filter basket,
blades and agitators, and accessories in general. There is also no
warranty for parts lost by the user.

ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO
THIS PRODUCT IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY
PERIOD.

Some states do not allow limitation on how long an implied warranty
lasts or do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

7

Assembly page 7/24

JK 39380 - 131101



Copies of the I/B. Please reproduce them without any

Fax [phone]

changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

If the appliance should become defective within the warranty
period and more than 30 days after date of purchase, do not return
the appliance to the store: often, our Customer Service
Representatives can help solve the problem without having the
product serviced. If servicing is needed, a Representative can
confirm whether the product is under warranty and direct you to the
nearest service location.

If this is the case, bring the product, or send it, postage prepaid by
the user (all Kalorik customers are responsible for the initial shipment
back to the warranty center), along with proof of purchase and a
return authorization number indicated on the outer package, given
by our Customer Service Representatives. Send to the authorized
KALORIK Service Center (please visit our website at
www.KALORIK.com or call our Customer Service Department for the
address of our authorized KALORIK Service Center).
When sending the product, please include a letter explaining the
nature of the claimed defect.

If you have additional questions, please call our Customer Service
Department (please see below for complete contact information),
Monday through Thursday from 9:00am - 5:00pm (EST) and Friday
from 9:00am - 4:00pm (EST). Please note hours are subject to change.

If you would like to write, please send your letter to:

KALORIK Customer Service Department

Team International Group of America Inc.
1400 N.W 159th Street, Suite 102
Miami Gardens, FL 33169 USA

Or call:

Toll Free: +1 888-521-TEAM / +1 888-KALORIK

Only letters can be accepted at this address above. Shipments and
packages that do not have a return authorization number will be
refused.

8

Assembly page 8/24

JK 39380 - 131101