Kalorik CM 38933 User Manual



Fax [phone]

Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

Coffee maker

Cafetera

Machine à Café

CM 38933

www.KALORIK.com

Front cover page (first page)

Assembly page 1/26

120V~60Hz - 1000W (8.3A)





Fax [phone]

Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always
be followed, including the following:

1. READ ALL INSTRUCTIONS

2. Check that your mains voltage corresponds to that stated on the
appliance.

3. Do not touch hot surfaces. Use handles or knobs.

4. To protect against electrical shock do not immerse the cord, plug, or
the main unit in water or any other liquid.

5. Please keep out of reach of children and pets. This product is not
intended for use by children, by persons with reduced physical, sensory
or mental capabilities, or lacking experience or knowledge, unless they
have been given supervision or instruction concerning the use of the
product, by a person responsible for their safety. Extra caution is always
necessary when using this product.

6. Close supervision is necessary when any appliance is used by or near
children.

7. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts.

8. Do not operate any appliance with a damaged cord or plug or after
the appliance malfunctions or has been damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair, or adjustment.

9. The use of accessory attachments not recommended by the appliance
manufacturer may cause injuries, fire or electric shock.

10. Do not use outdoors.

11. Do not let cord hang over edge of table or counter, or touch hot
surfaces.

12. Do not place on or near a hot gas or electric burner, or in a heated
oven.

13. Place the appliance on a flat, level surface that is waterproof.

14. Extreme caution must be used when moving an appliance containing
hot oil or other hot liquids.

15. To disconnect, put the switch in off position, then remove plug from wall
outlet.

16. Do not use appliance for other than intended use.

17. Scalding may occur if the lid of the coffee maker is removed during the
brewing cycles.

2

Assembly page 2/26

CM 38933 - 120501



Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good

Fax [phone]

18. Make sure the appliance never comes into contact with flammable
materials such as curtains, textiles… when it is in use as they might catch
fire.

19. When removing lime scale, only use special products for the removal of
lime scale. Never use ammonia or any other substance that might
damage your health.

20. Only put ground coffee in the filter. Always use a filter (paper or
permanent) in the filter holder.

21.

The appliance shall not be operated using a separate timer or separate
remote device.

22. Never use your coffee maker without water in it. If you have a
programmable coffee maker, make sure to fill it with water before
programming it.
Important: never put the jug in a microwave oven to warm up the
coffee. We will not take any responsibility if you do so.

numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

SAVE THESE INSTRUCTIONS

HOUSEHOLD USE ONLY

POLARIZED PLUG INSTRUCTIONS

This appliance is equipped with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug will fit into the
polarized outlet only one way. If the plug does not properly fit into the outlet
at first, reverse it. If it still does not fit, contact a qualified electrician. Do not

attempt to modify the plug in any way.

SHORT CORD INSTRUCTIONS

A short power supply cord is provided to reduce the hazards resulting from
becoming entangled in, or tripping over a longer cord. Extension cords may
be used if care is exercised in their use.

• The electrical rating of the extension cord should be at least that of

the appliance. If the electrical rating of the extension cord is too
low, it could overheat and burn.

• The resulting extended cord should be arranged so that it will not

drape over the counter top or tabletop where it can be pulled on by
children or tripped over.

3

Assembly page 3/26

CM 38933 - 120501



Fax [phone]

10

Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

PART DESCRIPTION

13

12

11

9

1

2

3

4
5

6

7

8

1. Water reservoir lid

2. Water reservoir with window

3. Cavity for filter holder

4. AUTO light

5. Hour adjustment button “H”

6. Minute adjustment button “M”

7. Tempered glass carafe

8. Heating plate

9. Drip stop mechanism (under
filter holder)

10. PROG button

11. On/Off button

12. Digital programmable clock
with backlit display

13. BREW light

TYPE OF FILTER:

4

Cone paper filter type 4 or permanent filter (included)

Assembly page 4/26

CM 38933 - 120501



Fax [phone]

Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

BEFORE FIRST USE

• When you use your appliance for the first time, pour fresh water into the
water tank (without coffee) and switch on the appliance.

• Once all the water has passed through, switch off the appliance and let
it cool down. When it is cold enough repeat the process 3 times with
fresh water.

SETTING THE CLOCK

To set the digital clock, press the PROG button (10). “CLOCK” is displayed
on the screen. Press the “H” button (5) until the clock displays the desired
hour. Press the “M” button (6) until the clock displays the desired number of
minutes. Press “PROG” button twice to exit the clock setting program.

PREPARATION OF COFFEE

• Open the lid (1) of the water tank (2) and pour the desired volume of
water in it. The water level can be read off the water level indicator.
Never exceed the maximum level indicated, corresponding to 12 cups
of coffee.

• Insert a paper filter, or the permanent filter supplied, into the filter holder;
place the removable filter holder in the cavity (3) and add the desired
quantity of ground coffee using the provided scoop.

• Never forget to close the water tank lid before switching on the coffee
maker.

• Put the carafe (7) with its lid closed on the heating plate.

• Plug in the coffee maker on a wall outlet.

• Press the ON/OFF button (11) once. The red light “BREW” (13) will

illuminate, indicating that your appliance is in use, along with the LCD
display of the clock (12). The screen will remain backlit during the whole
brewing process.

• Thanks to the electronic keep warm function, your coffee will be kept
warm for 2 hours, unless the coffee maker gets switched off (see below).

• Your coffee maker is equipped with a “Pause-and-Serve” aka drip stop
function (9), which means that when you remove the carafe from the
appliance, a non-drip valve will automatically operate to stop any
drops of coffee falling onto the heating plate (8). When you put the
carafe back into place, the non-drip valve opens automatically and
allows the remaining coffee to filter through, into the jug.

• Wait until the brewing process is finished and the filter is empty of water
before removing the carafe.

5

Assembly page 5/26

CM 38933 - 120501



Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good

Fax [phone]

numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

Practical hints: When the water tank is empty, wait a couple minutes longer

before removing the carafe, as some water might still drip out of the filter.
Note: the 2-hour auto-shut off feature is activated when operating the

coffee maker manually, or using the timer.

• To shut off your coffee maker manually before the 2-hour auto shut-off
period, press the ON/OFF button twice, until both lights and the light of
the LCD display are off.

PROGRAMMING THE COFFEE MAKER (DELAYED TIMER)

• To program your coffee maker to brew fresh coffee at a preset time, first
follow steps 1 to 4 in the “PREPARATION OF COFFEE” section.

• Make sure the coffee maker’s clock is set to the right time.

• Press the PROG button twice (10). The clock will now display 12:00 with

the word “TIMER” in the upper left corner. Use the “H” and “M” buttons
to set the desired brew time. Press PROG again to validate the timer
setting.

• Press the ON/OFF button (11) twice to activate the preset brew cycle.
The green AUTO light (4) will illuminate, when the brew time is properly
set.

• When your preset brew time is reached, and the coffee maker starts its
brew cycle, the green AUTO light (4) will go out, and the red BREW light
(13) will illuminate, along with the LCD display of the clock (12). The
screen will remain backlit during the whole brewing process.

• As with the regular brew cycle, an automatic two-hour keep warm
cycle will start after your coffee maker has finished brewing. At the end
of the two hours, the coffee maker will automatically shut itself off.

NOTE: the 2-hour auto-shut off feature will be activated when operating the
coffee maker manually, or using the timer.

• To shut off your coffee maker manually before the 2-hour auto shut-off
period, press the ON/OFF button twice, until both lights and the light of
the LCD display are off.

6

Assembly page 6/26

CM 38933 - 120501



Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good

Fax [phone]

numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

DESCALING AND CLEANING

• Before any cleaning, switch the appliance off and unplug it. Let it cool
down before cleaning or storage.

• The filter holder, the permanent filter, the carafe and the lid of the
carafe can be cleaned in warm soapy water.

• The coffee maker can be cleaned with a damp non-abrasive cloth or
sponge.

• Removing lime scale / mineral deposits in your coffee maker, on a
regular basis, will greatly prolong its life span. For decalcification, only
use products especially formulated for the descaling of coffee makers
and follow their instruction manual carefully. Do not use vinegar as it
may damage the internal pipes.

• Never put any part of the appliance in the dishwasher. Clean the
carafe with soapy water and rinse it with clear water.

PRACTICAL HINTS

Problem:

You notice that the coffee making process is longer than it should be.

Solution:

It is probably time to decalcify the appliance. Do not wait for the situation
to get worse. The decalcifying frequency depends on the hardness of the
water and therefore can be different from one household to another.
Therefore it is important to pay attention to this. A good maintenance of
your appliance will prolong its lifespan. Guarantee claims will not be
accepted for the replacement of a heating element full of mineral deposit.

Problem:

The carafe is hard to remove when in place.

Solution:

The heating plate is designed deep in order to optimize the keep warm
function. Please lift the carafe before removing it, or angle it slightly towards
the back before removal. To replace the carafe, also angle it slightly
towards the coffee maker.

7

Assembly page 7/26

CM 38933 - 120501



Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International USA. The pages must be reproduced and folded
in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm
height). When folding, make sure you keep the good

Fax [phone]

numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only

what is inside the frame.

WARRANTY

We suggest that you complete and return the enclosed Product
Registration Card promptly to facilitate verification of the date of
original purchase. However, return of the Product Registration Card is
not a condition of these warranties. You can also fill out this warranty
card online, at the following address: www.KALORIK.com

This KALORIK product is warranted in the U.S.A. for 1 year from the
date of purchase against defects in material and workmanship. This
warranty is not transferable. Keep the original sales receipt. Proof of
purchase is required to obtain warranty performance.

During this period, if the KALORIK product, upon inspection by
KALORIK, is proven defective, it will be repaired or replaced, at
Kalorik’s option, without charge to the customer. If a replacement
product is sent, it will carry the remaining warranty of the original
product.

This warranty does not apply to any defect arising from a buyer's or
user's misuse of the product, negligence, failure to follow KALORIK
instructions noted in the user’s manual, use on current or voltage
other than that stamped on the product, wear and tear, alteration
or repair not authorized by KALORIK, or use for commercial purposes.
There is no warranty for glass parts, glass containers, filter basket,
blades and agitators, and accessories in general. There is also no
warranty for parts lost by the user.

ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO
THIS PRODUCT IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY
PERIOD.

Some states do not allow limitation on how long an implied warranty
lasts or do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

If the appliance should become defective within the warranty
period and more than 30 days after date of purchase, do not return

8

Assembly page 8/26

CM 38933 - 120501