Fax No: 01264 723 576
Email: support@kalika.co.uk
Web: www.kalika.co.uk
ULYDOR BY KALIKA
(PBX Door Entry Systems)
Operating Instructions
2 Ulydor Door Entry Systems – Operating Instructions
Thank you for purchasing our Ulydor PBX Modular Door Entry System.
Ulydor is a highly versatile door entry system, allowing units from 0-64
buttons to be built.
When a visitor arrives at the building it allows them to select from the
name panel the company/person they wish to visit. The visitor presses the
button for that company/person and the appropriate telephone then rings
and allows a conversation to take place. To allow the visitor access the
company/person presses a two digit code on the handset, activating the
door lock and enabling entry to the building.
Ulydor works with most telephone systems able to provide a two wire
analogue extension. With every installation a Ulydor Control Unit will be
required of which there are three options: a UC0 (No Buttons), UC1 (One
Button) and a UC2 (Two Buttons). By adding C4 (4 button extension
control module) and M4 (4 button slave module) units, a system of 0-64
buttons can be built. Each button can be programmed with up to a 16 digit
number, including *, #, pause and hook flash.
Examples of Ulydor Entry Systems
Buttons Modules No. of Modules MK-x
0 UC0 1 1
1 UC1 1 1
2 UC2 1 1
4 UC0 - C4 2 2
5 UC1 - C4 2 2
6 UC2 - C4 2 2
8 UC0 - C4 - M4 3 3
9 UC1 - C4 - M4 3 3
10 UC2 - C4 - M4 3 3
12 UC0 - 2 x C4 - M4 4 4
13 UC1 - 2 x C4 - M4 4 4
14 UC2 - 2 x C4 - M4 4 4
16 UC0 - 2 x (C4+M4) 5 3 + 2
17 UC1 - 2 x (C4+M4) 5 3 + 2
18 UC2 - 2 x (C4+M4) 5 3 + 2
20 UC0 – 3 x C4 – 2 x M4 6 3 + 3
21 UC1 – 3 x C4 – 2 x M4 6 3 + 3
22 UC2 – 3 x C4 – 2 x M4 6 3 + 3
24 UC0 – 3 x C4 – 3 x M4 7 4 + 3
25 UC1 – 3 x C4 – 3 x M4 7 4 + 3
26 UC2 – 3 x C4 – 3 x M4 7 4 + 3
28 UC0 – 4 x C4 – 3 x M4 8 4 + 4
29 UC1 – 4 x C4 – 3 x M4 8 4 + 4
30 UC2 – 4 x C4 – 3 x M4 8 4 + 4
64 UC0 – 8 x C4 – 8 x M4 17 4 + 4 + 4 + 4 +1
Keypad can only be added on systems between 0 – 18 buttons.
Camera module can be added on any combination of buttons.
3 Ulydor Door Entry Systems – Operating Instructions
The Ulydor Control Modules can also be used in conjunction with a UCK
(12 Button Keypad Module) – particularly useful for staff entry.
Ulydor is supplied with 2 relays allowing the control of two doors for
opening and closing as well as lighting, cameras, etc.
The programming of a Ulydor Door Entry System is carried out by the use
of Windows based software supplied with all UC modules, or by the use of
the telephone keypad. It can also be carried out remotely and those with
the system code can program or re-program remotely by use of a GSM
mobile telephone or by connecting a jumper on the PCB. If a password is
forgotten, then re-programming would be carried out by use of the jumper.
4 Ulydor Door Entry Systems – Operating Instructions
TABLE OF CONTENTS
1 BASIC DESCRIPTION ………………………………………………. 6
1.1 Features ……………………………………………………... 6
1.2 Module Assembly ………………………………………….. 7
2
INSTALLATION OF ULYDOR ASSEMBLY ………………………
9
2.1 Installation of Surface Mount Module …………………. 9
2.2 Flush-Mounted Installation ………………………………. 9
2.3 Change of Nameplates ……………………………………. 10
2.4 Installing the Modules …………………………………….. 11
2.4.1 UCx Basic Module ……………………………... 11
2.4.2 Extending Modules - C4 & M4 ….................. 13
2.4.3 UCK – 12 Button Keypad Module …………… 14
2.4.4 Signalling Overview …………………………… 15
3
USING ULYDOR ……………………………………………………... 16
3.1 Ulydor System Without & With Keypad ……………….. 16
3.1.1 Without Keypad ………………………………... 16
3.1.2 With Keypad ……………………………………. 17
3.2 Using the System ………………………………………….. 18
3.2.1 Outgoing Call …………………………………… 18
3.2.2 Incoming Call …………………………………… 18
4
PROGRAMMING OF PARAMETERS …………………………….. 19
4.1 Programming through Phone …………………………… 19
4.1.1 Entry to Programming ………………………… 19
4.1.2 Programming of Parameters ………………… 19
4.2 Programming from PC – Program Nset ……………….. 20
4.3 Overview of Parameters ………………………………….. 21
4.4 Description of Parameters ……………………………….. 22
4.4.1 Direct Dialling – Memories …………………… 22
4.4.2 Relays ……………………………………………. 23
4.4.3 Basic Parameters ……………………………… 25
4.4.4 Time Parameters ………………………………. 27
4.4.5 Presetting and Deleting ………………………. 29
4.4.6 Programming Termination …………………… 29
4.5 System Setting ……………………………………………... 29
4.6 List of Presetting Parameters …………………………… 30
5
TECHNICAL PARAMETERS ………………………………………. 31
5.1 Electrical Parameters ……………………………………... 31
5.2 Mechanical Dimensions ………………………………….. 31
6
TABLE OF EASY PROGRAMMING ………………………………. 32
5 Ulydor Door Entry Systems – Operating Instructions
TABLE OF CONTENTS (Contd)
7
DISTY 300 …………………………………………………………….. 34
7.1 Description ………………………………………………….. 34
7.2 Signalling ……………………………………………………. 34
7.2.1 LED Indication ………………………………….. 34
7.2.2 Tones …………………………………………….. 35
8
IP CAMERA …………………………………………………………... 37
6 Ulydor Door Entry Systems – Operating Instructions
1 BASIC DESCRIPTION
1.1 Features
• Modular system allows connection of 0 - 64 buttons.
• Voice link is supplied from telephone extension.
• Pulse and Tone dialling (DTMF).
• Two 16 digit numbers with each button (including ρ, #, Hook Flash /
Recall and Pause).
• Day / Night switching.
• Extend call time by ρ or #
• Connection of two independent locks or activate other devices.
• 5 switching modes (e.g. camera, lighting, gradual opening, etc).
• Two codes for hanging up the Ulydor from the telephone.
• Two codes for door opening from the telephone.
• Six code locks (password from buttons at the door).
• Optional keypad, on systems with between 0-18 standard buttons.
• Keypad modes can be for direct dialling or memory dialing.
• Optional maximum number of rings to answer an incoming call.
• Optional time interval between button pressing for code entry.
• Optional time for hanging up before redial.
• Optional time before alternative number call.
• Optional parameters for tone choice, length of Recall and Pause.
• Default setting of some parameters.
• Besides the Preset Basic setting it is possible to preset two
alternative default settings.
• Remote telephone programming using DTMF tones or direct from a
PC.
• Integrated heating of printed circuit
• Permanent lighting buttons and name cards.
• Earth connection for better protection against static electricity.
7 Ulydor Door Entry Systems – Operating Instructions
1.2 Module Assembly
The structural elements of Ulydor are the basic modules: UC0, UC1,
UC2 and extending button modules C4 and M4 with four buttons.
UC0 Module UC1 Module UC2 Module C4/M4 Module
It is possible to provide the assembly with numerical keypad and camera
module (IP, WI-FI, Coax).
UCK Module
IP Camera Analogue Camera DECT Disty Box
The complete assembly consists of a system of maximum 4 modules in
column and maximum 3 columns side by side. Examples of frame
configuration are:
8 Ulydor Door Entry Systems – Operating Instructions
SMB1
Protected Cabinet &
Cosmetic Surround
SMB2
Protected Cabinet &
Cosmetic Surround
SMB4
Proected Cabinet &
Cosmetic Surround
FMBB2
Flush Mount Back Box
Cosmetic Surround
UC2 + C4 + FMBB2 (Horiz)
9 Ulydor Door Entry Systems – Operating Instructions
2 INSTALLATION OF ULYDOR ASSEMBLY
2.1 Installation of Surface Mount Module
The installation of a SMBx Surface Mount Box is
made by screwing the assembly to the wall.
2.2
Flush-Mounted Installation
The FMBBx box is mounted into the wall and secured by the fixing
screws provided. Lugs are provided for joining FMBBx boxes together if
larger installations are required.
The cosmetic protecting frame provides an
overlap to aid any unevenness when mounting
the box into the space created in the wall. The
canopy (EWHx) is necessary for installations in
external areas and is an accessory for the
FMBBx box and replaces the need for the
FMBBx cosmetic surround. When installed in exposed areas that are
subject to condensation, temperature changes, waterspray, or rain it is
recommended that the EWHx box is used and that the heater connector
is jumpered onto the UCx module and set to the "ON" position.
The BOARD HEATING has two positive functions.
Firstly, it heats up the electronics in winter at
temperatures -20oC (temperature range has
guaranteed parameters from -20oC), and secondly
with external installations experiencing rapid
temperature changes in humid areas the heater
prevents condensation on the Ulydor UCx PCB.
10 Ulydor Door Entry Systems – Operating Instructions
2.3
Change of Nameplates
The first step is to dismantle the fixing frame (See Diagram 1) by
removing the two hidden screws top and bottom. Remove the modules
requiring information change by inserting a screw driver into the side of
the module (See Diagrams 2 and 3). Each module is in two parts, the
front facia plate being metal and the back plate being plastic. Separate
the two parts and note that each button has its own nameplate located
under a clear plastic flag (See Diagram 4). New information can be
printed from the Nset program on the supplied CD or downloaded from
www.kalika.co.uk
Diagram 1 Diagram 2
Diagram 3 Diagram 4
11 Ulydor Door Entry Systems – Operating Instructions
2.4 Installing the Modules
2.4.1 UCx Basic Module
The Ulydor basic module is supplied in
three variants:
UC0 - No Buttons
UC1 - One Button, and
UC2 - Two Buttons
Figure 1 - Rear view of Basic Module
The telephone extension circuit from the PBX / line should be connected
to the terminal marked "ab line" (See Figure 1). The Ulydor circuits are
powered from the telephone line and nothing extra should be required to
make voice communication.
If one or two relays are to be used, an AC PSU of between 10V – 15V,
or with DC PSU between 12V – 18V must be connected to the "12V"
terminal. The PSU loading depends on number of modules, since it
feeds backlighting to the name card display. With the maximum number
of modules the demand will not exceed 300mA. If the PSU is also used
for power feed to the lock(s), then consideration needs to be given to the
electrical demands of the lock(s). In practice a 12V/1A meets these
demands.
12 Ulydor Door Entry Systems – Operating Instructions
The connection of relay contact terminals is shown in Figure 1. The
"NO" designation means a normally open relay contact, "COM" means a
pin contact (middle) and "NC" means a normally closed contact. The
contacts of both relays are galvanically isolated from each other and
from other Ulydor circuits. The connection variations are shown in
Figure 2.
Figure 2 - Examples of Switch Connections
The "G" Faston 2.8mm terminal protects against static electricity (to be
connected to earth).
The "VOLUME" trimmer allows adjustment to the volume of the
loudspeaker, it has no effect on other Ulydor features. The "MIC"
trimmer (placed under PDV board) provides the adjustment of
microphone volume. Such adjustment can improve the quality of speech
when subjected to ambient noise in the street, etc.
13 Ulydor Door Entry Systems – Operating Instructions
The "HEAT" jumper allows the switching of board heating. This function
requires the connection of 12V supply on "12V" marked terminal.
The "EXPANSION" marked connector serves the connection of
extending modules by means of flat cable.
The "PRG" marked connector provides the Ulydor adjustment from the
PC by means of serial cable and allows service programming and new
software uploads.
The "SERVICE" jumper allows direct access to programming. It can be
used in the absence of password for programming.
2.4.2 Extending Modules – C4 & M4
These modules are supplied in two designs.
The C4 module has four buttons
and includes the electronics to
connect to a UCx module. The
C4 is connected to a UCx by a flat
cable for additional buttons and
lighting. The flat cable connector
block is designed for one way
connection to prevent incorrect
alignment and therefore keeps the
connection routing correct.
The M4 (slave) module has four
buttons which connect via
terminal blocks on the previous
C4 module. The connections are
individually wired by screw
terminals (See Figure 3).
Remember:
Ulydor C modules always connect
in series, using the flat cable
connectors to the main control
unit (UCx). A module always
connects to a C4 module.
Figure 3 – Connection of C4 & M4
14 Ulydor Door Entry Systems – Operating Instructions
2.4.3 UCK – 12 Button Keypad Module
The keypad module is connected by flat cables to the
UCx or the C4 module. The keypad module is always the
last module in the row (no other module can be
connected beyond it). It can only be linked to the control
module, or the first/second C4 modules. This means that
systems with a keypad support a maximum of 18 direct
dial buttons. The possible assemblies of modules are:
• UCx + UCK (Position 1)
• Ucx + C4 + UCK (Position 2) + M4 (if required)
• Ucx + C4 + C4 + UCK Position 3) + 2 x M4 (if required)
Note: when programming the position of keypad connection must be
correctly specificed (parameter 48).
The extension or memory choice is entered by
pressing the numeric buttons. The key symbol must
be pressed first before entering a password. When
pressing X, the Ulydor will hang up.
2.4.3 Other Modules
Other extending modules are offered and can be ordered through your
supplier.
15 Ulydor Door Entry Systems – Operating Instructions
2.4.4 Signalling Overview
Ulydor signals acoustic tones during its operation. There is a further
signal provided by an LED placed on the main control unit.
Condition Tones
Tone
frequency
LED
Line lifting up –▄–■–▀– 425-850-1275 glows
Line hanging up –▀–■–▄ 1275-850-425 goes out
Report after calling –▄–■–▀– 425-850-1275 glows
Command confirmation from phone ––█–– 425
Dialling DTMF/Pulse goes out
Call glows
Notice about call end –■–■–■– 1275 glows
Entry to programming from phone –■–■–■– 850 glows
Programming from phone ––▓–▓––––– mod. 850 glows
Parameter confirmation ––█–– glows
Entry to programming from PC –■–■–■– 850 glows
Programming from PC blinks
Connection to line (Reset) –■–▄–■– 1275-850-1275 blinks
Error (anything if unsuitable) –■–■–■–■–■–■– 425….
Empty memory (no programming number) –█–▄–■–▄–■–▄– 850-1275-1700.
16 Ulydor Door Entry Systems – Operating Instructions
3 USING ULYDOR
Ulydor functions are influenced partly by the modules used (with or
without keypad module) and partly by the Ulydor system parameters.
For instance, if a single button module is installed the functions relate
purely to that particular module's parameters. As another example, if a
keypad is added the parameters of the keypad settings will affect some
parameters of programming the main control unit.
3.1 Ulydor System Without & With Keypad
3.1.1 Without Keypad
The system buttons are provided by the side of the nameplates for
company/person extension inside the building. The visitor will press the
corresponding button, the Ulydor System will open up the line either
immediately, or with delay (parameter 53) and after the period given by
parameter 55 will dial the programmed phone number. The dialling
number differs by choice mode, which is set in the Ulydor System
(parameter 47):
- Day / Night mode – when the Ulydor System is set in Day mode, it
is always dialling a number set in parameter 1. When in Night
mode, it is always dialling a number set in parameter 2. The mode
switchover is set in parameters 45, 46.
- mode of second number group = first press – it always dials a
number set in parameter 1. By repeated pressing of the same
button or detection of a busy tone after dialling the Ulydor System it
will select the number from the second group (parameter 2). The
next press of the same button again selects a number of the first
group, etc.
If a visitor presses the button after the Ulydor System has already
provided a line, the system will hang up for a given period (parameter
54), at the end of that period it will then reopen and dial a new number.
The number choice is carried out in tone (DTMF), and pulse dialling
according to the setting of parameter 41. Almost in all cases in the UK it
will require DTMF.
17 Ulydor Door Entry Systems – Operating Instructions
The relay (code lock) can be controlled by the first 10 buttons of Ulydor.
If the visitor presses buttons in a combination that meets the preprogrammed code (parameters 32-34) and the time among presses is
not bigger than the set point (parameter 53), then the Ulydor will
activate and deactivate the corresponding relay (if set in m=1 or m=5
modes) to the period given by parameter 36 event. 38. Then it will hang
up the line.
3.1.2 With Keypad
The Ulydor System with keypad can also include
(besides the keypad) up to 10 buttons of direct dialling
always behaving as mentioned in Chapter 3.1.1,
except the code lock as this is always situated on the
keypad. After the keypad is connected, the position of
where the keypad is connected should be set
(parameter 48).
The keypad has two functional buttons:
key symbol = pressing the numerical combination is considered as
the combination for control of the relays.
X symbol = when pressing X the Ulydor immediately will hang
up.
The number selection on the keypad can be executed in two ways
(parameter 49):
- The incoming person dialling a number (extension) as would be
done on a phone – the period among button presses should be
lower than the value given by parameter 53. After this period the
Ulydor System will lift up and dial the given number.
- On memory mode the incoming person is dialling a two-digit number
relative to the preset buttons (from 01-64), which represents the
memory number, where the 16-digit number is stored (same as for
buttons). The number dialling is managed by Day / Night setting or
mode for two groups of numbers (as described in Chapter 3.1.1).
18 Ulydor Door Entry Systems – Operating Instructions
3.2 Using the System
3.2.1 Outgoing Call
An outgoing call is a call from the Ulydor (made by the visitor) to an
internal user's telephone. After the visitor presses a button, the door
entry system calls the internal telephone, which when answered, will
allow voice connection to the visitor at the door. Using the telephone
keypad, the internal user can then activate the relays (parameter 35),
change over the Day / Night modes (parameters 45, 46) and hang up
(parameter 43). 10 seconds before the call ends (parameter 52) the
Ulydor will send a noticeable tone, signalling the call is about to end.
However, the call may be extended by pressing the * key (parameter
42). When the user ends the call the PBX sends a busy tone to the
Ulydor and the Ulydor also hangs up.
3.2.2 Incoming Call
An incoming call is a call from an internal user's telephone to the Ulydor.
After the extension number of the Ulydor is dialled, the Ulydor will ring
and after a set number of rings (parameter 51) will answer whereupon it
is possible to speak. The possibilities are the same as with an outgoing
call (Chapter 3.2.1).
• During the first 10 seconds, # followed by the service password
(parameter 44) can be entered. The Ulydor will then enter
programming mode.
• The other exception of an incoming call is by connecting the
“SERVICE” jumper. The Ulydor will automatically enter programming
mode when answering an incoming call. This facility should be used
if you have forgotten the service password. Warning: Never leave
a system installed with the "SERVICE" jumper connected.
19 Ulydor Door Entry Systems – Operating Instructions
4 PROGRAMMING OF PARAMETERS
4.1 Programming through Phone
4.1.1 Entry to Programming
The Ulydor System can be set to programming mode in two ways:
1. by password – Dial the extension number of the Ulydor and the
Ulydor will answer. Within the first 20 seconds you should dial
#xxxx (where xxxx is the programming password). If correct, the
registration tone to programming will sound and afterwards the
programming tone can be heard.
2. by "SERVICE" jumper – dial the extension number of the Ulydor
and the Ulydor will answer in programming mode – you hear tone
for answering, registration tone to programming and afterwards
the programming tone can be heard. You should only use the
"SERVICE" jumper if you have forgotten the password!
4.1.2 Programming of Parameters
The initial state for programming is signalled by the programming tone
and the Ulydor will return to this state after 5 seconds with no DTMF
input (even if you have started programming).
There are two types of parameter:
fixed length – the majority of parameters are of fixed length. After
entering the parameter you will hear an acknowledge tone.
variable length – some of the parameters are of a variable length. A
good example is the parameters which store the numbers dialled when a
user presses a button. After entering the parameter you should wait 5
seconds until you hear the confirmation tone.
If during programming you enter an invalid digit the Ulydor will
immediately emit an error tone. The parameter will not be recorded nor
changed, the Ulydor will return to programming mode and it is possible
to repeat the parameter setting or program another parameter.
20 Ulydor Door Entry Systems – Operating Instructions
The Ulydor stays inactive in programming mode for 34 seconds then it
will automatically hang up. You can also end the programming mode by
pressing 9.
Note 1:
if you wish to keep the connection (extend beyond the 34 second
period), press 6, 7, 0, * or # from time to time. The Ulydor
immediately responds by error tone and will extend the period before
hanging up.
Note 2: When entering the door release passwords (parameters 32,
33, 34), you can finish with the # key. This will save you waiting 5
seconds for the confirmation tone.
4.2 Programming from PC – Program Nset
The Ulydor can be set up from a PC. The special RS232 PROG cable
should be connected to a serial port and the Nset program should be
installed. The Ulydor has to be connected to a telephone line.
Procedure:
- Connect the Ulydor to the telephone line
- Connect the Ulydor to the PC via the programming cable (if there is
no serial port on your PC use a SUB – RS232 adapter). The Ulydor
will answer and the LED light on the front panel will light.
- Run the Nset program – the Ulydor will report entry to PC
programming mode. While the Nset software program is being used
the Ulydor will be in programming mode – this status is indicated by
a flashing LED (1 second on 1 second off) on the front of the UC
module. If the connection to the Nset software is lost it will be
necessary to disconnect and reconnect the RS232 programming
cable. The Ulydor UC module will answer and will indicate re-entry
to programming mode.
21 Ulydor Door Entry Systems – Operating Instructions
4.3 Overview of Parameters
Param. Value Meaning Basic Exam.1 Exam.2
1
tt nn…
Number nn under button tt
- - -
2
tt nn…
Number nn under button tt
- - -
31
r m
replay r works in m mode
11 21 11 22 11 25
32
r hhhhhh
Password hhhhhh for r relay in Day +
Night mode
-
1 121
2 122
1 4561
2 4562
33
r hhhhhh
Password hhhhhh for r in Day
mode
- - -
34
r hhhhhh
Password hhhhhh for r in Night
mode
- - -
35
r aa
Command aa from phone after r relay
closing
155 266 155 266 155 266
36
r ss
ss period [sec] of r relay closing
105 205 102 202 105 205
37
r p
r relay control by incoming call
11 21 11 21 11 21
38
Xx
xx period [sec] between relays 1 & 2
closing
10 10 15
41
V
Choice type v – tone / pulse
0 0 0
42
Z Sign for call extension
* * *
43
g bb
Command for Ulydor hanging up from
phone
155 266 155 244 155 244
44
Xxxx Service password 0000 0000 0000
45
Dd
Command for Day switching
11 11 11
46
Nn
Command for Night switching
10 10 10
47
E Mode of Ulydor choice 0 1 0
48
C Keypad connection 0 0 1
49
O Keypad mode 0 1 0
51
Q
Number of rings before Ulydor call
lifting up
2 1 2
52
D Maximum call time 2 2 1
53
W Time among button presses 2 2 2
54
Z
Time of hanging up when dialing
repeated
2 2 2
55
Z Time before dialling 1 1 1
56
H Number of rings before hanging up 12 12 12
57
T DTMF tone duration (tone) choice 5 (100ms) 5 (100ms) 5 (100ms)
58
M Gap duration among DTMF tones 5 (100ms) 5 (100ms) 5 (100ms)
59
F Flash duration 1 (100ms) 1 (100ms) 1 (100ms)
50
P Pause duration / interdigit gap 8 (800ms) 8 (800ms) 8 (800ms)
8#
# Basic setting executes
8#
1 Setting per example 1 executes
8#
2 Setting per example 2 executes
81
Deletes all numbers in group 1 (Day)
82
Deletes all numbers in group 2 (Night)
83
Basic setting only for parameters 3x only 3..
84
Basic setting only for parameters 4x only 4..
85
Basic setting only for parameters 5x only 5..
9
E N D
22 Ulydor Door Entry Systems – Operating Instructions
4.4 Description of Parameters
4.4.1 Direct Dialling – Memories
Group 1 – Day Mode
Param. Value Meaning Basic Exam.1 Exam.2
1 tt nn…
No. nn under button tt - - -
tt – button number (memory), always set in two-digit manner [0164]
nn – telephone number up to 16 digits, we want
to store. To store other choice flags the
assignment given in the table is used.
The numbers stored in parameter 1 are the number of
the first group or numbers of Day mode. Neither the
basic setting nor settings per examples change or delete the stored
numbers.
Group 2 – Night Mode
Param. Value Meaning Basic Exam.1 Exam.2
2 tt nn… No. nn under button tt
- - -
tt – button number (memory) is always set in two-digit manner
[01-64]
nn – telephone number up to 16 digits that is to
be stored. To store other choice flags the
assignment given in the table is used.
The numbers stored in parameter 2 are the numbers
of the second group or numbers of Night mode.
Neither the basic setting nor settings per the examples change or delete
the stored numbers.
Note: The switchover to Day / Night mode remains set in the Ulydor
System even after the line has been disconnected
.
meaning choice
0 - 9 0 - 9
# #
* **
Flash * #
Pause * 0
meaning choice
0 - 9 0 - 9
# #
* **
Flash * #
Pause * 0
23 Ulydor Door Entry Systems – Operating Instructions
4.4.2 Relays
Param. Value Meaning Basic Exam.1 Exam.2
31 R m relay r works in m mode
11 21 11 22 11 25
r – relay number [1-2]
m – relay mode [for r=1 1-4 , for r=2 1-5]
m=1 relay mode – will activate on command or password for ss period
(used for electrical locks, gate opening etc.)
m=2 camera mode – will activate when Ulydor goes off-hook and de-
activates by hanging up.
m=3 lighting mode – will activate when Ulydor goes off-hook and stays
activated for ss period after Ulydor line hangs up (the line is
engaged for this period).
m=4 switch mode – will close after button pressing and open after ss
period (used for e.g. external bell or horn connections).
m=5 delay opening mode – Only applies to relay 2. Relay 1 is
automatically set to mode 1. Relay 1 is activated for ss period,
then time xx is proceeding before switch 2 activated. Then relay 2
is activated for ss period and afterwards the Uldyor System hangs
up.
Note: Only Relay 1 can be activated from the phone, Relay 2 can be
separately activated from buttons by password.
Passwords
Param. Value Meaning Basic Exam.1 Exam.2
32 r hhhhhh
Password hhhhhh for relay r in
DAY + NIGHT mode
-
1 121
2 122
1 4561
2 4562
33 r hhhhhh
Password hhhhhh for relay r in
DAY mode
- - -
34 r hhhhhh
Password hhhhhh for relay r in
NIGHT mode
- - -
r – relay number [1-2]
hhhhhh – password for relay closing from buttons or keypad
[2 to 6 digits]
Total of 6 passwords, they are controlled by Day / Night; the
combination is entered either by Ulydor System buttons (first 10 buttons)
or from attached keypad (after pressing of key symbol). The relay
closing influences the set relay mode and Day / Night switchover. By
setting of choice mode of 2 number groups the Ulydor System is
permanently in DAY mode.
24 Ulydor Door Entry Systems – Operating Instructions
By password choice some rules have to be observed:
Select passwords in a way that would make it difficult to find its
combination out, e.g.from wear of certain buttons by frequent use.
Select the first password button from frequentless button for direct
dialling (- extends choice time) (- not valid for keypad).
Pay attention to congruity of password numbers when one password
includes other one, e.g. relay 1 has 1234 and relay 2 has 12345.
Then after pressing button 4 only relay 1 is called, but password
choice 234 for relay 2 can call both relays after pressing relay 4.
Note: The switchover to Day / Night mode remains set in Ulydor even
after line disconnection
.
Operating Relays from the Remote Phone
Param. Value Meaning Basic Exam.1 Exam.2
35 r aa
command aa from phone after
r relay closing
155 266 155 266 155 266
r – relay number [1-2]
aa – command from phone after relay closing [2 digits]
The same command can be set for both relays and they are activated at
the same time. The advantage is to set the same command both for
relay closing and command to Ulydor hanging up (parameter 43)
aa=bb.
Relay Operating Time
Param. Value Meaning Basic Exam.1 Exam.2
36 r ss ss period [sec] of r relay closing
105 205 102 202 105 205
r – relay number [1-2]
ss – duration of relay closing [2 digits 01-99]
Relay Operation During Incoming Call
Param. Value Meaning Basic Exam.1 Exam.2
37 R p r relay control by incoming call
11 21 11 21 11 21
r – relay number [1-2]
p – parameter:
p=1 allowed, or
p=0 prohibited to control the relay during an incoming call.
This function prohibits the control of relays during an incoming call.
25 Ulydor Door Entry Systems – Operating Instructions
Duration Between Operation of Relays 1 & 2 (Mode 5 only)
Param. Value Meaning Basic Exam.1 Exam.2
38 xx
xx period [sec] between relays
1 & 2 closing
10 10 15
xx – time between operation of relays 1 and 2 by m=5 mode setting
(gradual opening) [2 digits 01-99]
4.4.3 Basic Parameters
Param. Value Meaning Basic Exam.1 Exam.2
41 v choice type v – tone / pulse
0 0 0
v – choice type v=0 is DTMF tone choice, v=1 is pulse choice
Param. Value Meaning Basic Exam.1 Exam.2
42 z
sign for call extension * * *
z – sign for call extension * or # (10 sec before call end the Ulydor
will
send a notice, then the call may be extended)
Param. Value Meaning Basic Exam.1 Exam.2
43 g bb
command for Ulydor hanging up
from phone
155 266 155 244 155 244
g – command order [1-2] (two commands in order to hang up the
Ulydor using both relays)
bb –
command for Ulydor hanging up from phone
[2 digits]
It is recommended to set the same command both for relay operation
and the command for Ulydor to hang up.
Param. Value Meaning Basic Exam.1 Exam.2
44 xxxx
service password 0000 0000 0000
xxxx – service password for entry to programming
26 Ulydor Door Entry Systems – Operating Instructions
Param. Value Meaning Basic Exam.1 Exam.2
45 dd command for DAY switching
11 11 11
46 nn command for NIGHT switching
10 10 10
dd – command for DAY mode switching [2 digits]
nn – command for NIGHT mode switching [2 digits]
Note: The switchover to Day / Night mode remains set in Ulydor even after line
disconnection.
Param. Value Meaning Basic Exam.1 Exam.2
47 e
mode of Ulydor choice 1 1 0
e – mode of Ulydor choice:
e = 0 selects numbers of the first and second groups,
e = 1 selects number per Day / Night DES mode.
Param. Value Meaning Basic Exam.1 Exam.2
48 c
keypad connection 0 0 1
c – c = 0 only NC-mode connected to the basic module
c = 1 keypad connected on the first position
c = 2 keypad connected on the second position
c = 3 keypad connected to the third position
ATTENTION !! This parameter setting will sharply influence keypad
function.
Param. Value Meaning Basic Exam.1 Exam.2
49 o
keypad mode 0 1 0
o – o = 0 dialling as on normal telephone (the number of the
person to be contacted should be pressed on the
keypad).
o = 1 only the 2-digit memory number (the stored number of
the person to be called), is entered on the keypad
(memory number and corresponds to button number
with respect to Day / Night switchover).
ATTENTION !! This parameter setting will sharply influence keypad
function.
27 Ulydor Door Entry Systems – Operating Instructions
4.4.4 Time Parameters
Param. Value Meaning Basic Exam.1 Exam.2
51 q
Number of rings before Ulydor answers 2 1 2
q – Number of incoming call rings, the Ulydor System lifts up
between rings, namely 2 seconds after detection q – times
rings. The number can be set from 1 to 9.
Param. Value Meaning Basic Exam.1 Exam.2
52 d
maximum call time 2 2 1
d – maximum call time before the Ulydor hangs up. This time can
be extended during a call by sign choice
on the telephone (* or #). Time setting
is per the table.
Param. Value Meaning Basic Exam.1 Exam.2
53 w
time between button presses 2 2 2
w – maximum time [sec] between button presses [range 1-9]
normal buttons
- relay closing – if the time between the next two
presses is bigger than w time, the code is not
evaluated correctly.
- dialling – if the button being pressed is the first
password number for relay closing, then choice is
delayed by this w time.
keypad
- relay closing – if time between the next two presses
is bigger than w time, the code is not evaluated
correctly.
- Dialling - is the same as of a telephone: if length of
time after the last pressed button is longer than w time
then the dialling starts. If the number is incomplete it
is necessary to hang up (X button) and the dialling will
be repeated.
- dialling from memory: if length of time following
the first pressed button is longer than w time then
the entry of memory number has to be repeated.
mean. choice
0 - 9 0 - 9
# #
* **
Flash * #
Pause * 0
28 Ulydor Door Entry Systems – Operating Instructions
Param. Value Meaning Basic Exam.1 Exam.2
54 z
time of hanging up when dialling
repeated
2 2 2
z – time [sec] for which the Ulydor will hang up before repeated
dialling (button pressing during call or dialling, busy tone
detection) [range 1-5]
Param. Value Meaning Basic Exam.1 Exam.2
55 z
time before dialing 1 1 1
z – time [sec] between the Ulydor going off-hook and dialling
[range 1-5]. This time is different for each exchange but
most central exchanges usually manage to process dialling
up to 2 seconds after line lifting up.
Param. Value Meaning Basic Exam.1 Exam.2
56 h
No. of rings before hanging up 12 12 12
h – when dialling has been completed it calculates the number
of KVT (ringing tones). If the number exceeds h value it
will hang up [range 04-99]. The dialling is repeated when the
dialling mode of 2 groups is set.
Param. Value Meaning Basic Exam.1 Exam.2
57 t
DTMF tone duration (tone)
choice
5 (100ms) 5 (100ms) 5 (100ms)
58 m
gap duration among DTMF
tones
5 (100ms) 5 (100ms) 5 (100ms)
59 f
Flash duration 1 (100ms) 1 (100ms) 1 (100ms)
50 p
pause duration / interdigit gap 8 (800ms) 8 (800ms) 8 (800ms)
t - DTMF tone duration is determined per formula:
(no. entered + 5) x 10 = tone duration [ms] [range 1-0 i.e. 60-150ms]
m - gap duration among DTMF tones is determined per formula:
(no. entered + 5) x 10 = gap duration [ms] [range 1-0 i.e. 60-150ms]
f - flash duration is determined per formula:
no. entered x 100 = Flash duration [ms] [range 1-6 i.e. 100-600ms]
p - pause duration is determined per formula:
no. entered x 100 = pause duration [ms] [range 5-0 i.e. 500-1000ms]
- p time is simultaneously the duration of interdigit gap at pulse dialling.
29 Ulydor Door Entry Systems – Operating Instructions
4.4.5 Presetting and Deleting
Param. Value Meaning Basic Exam.1 Exam.2
8# #
basic setting executes
8# 1
setting per exam. 1 executes
8# 2
setting per exam. 2 Executes
This setting does not influence 1 and 2 (numbers stored in memory)
Param. Value Meaning Basic Exam.1 Exam.2
81
deletes all numbers in group 1
(Day Mode)
82
deletes all numbers in group 2
(Night Mode)
83
basic setting only for params. 3x only 3..
84
basic setting only for params. 4x only 4..
85
basic setting only for params. 5x only 5..
Parameters 81 and 82 will execute deleting of all numbers stored in
memories for buttons. Parameters 83 – 85 will execute a selective basic
setting only for parameters starting with 3.. – 5..
ATTENTION !!! Deleting is non-reversible!!! It will be necessary to
reprogram if deleted.
4.4.6 Programming Termination
Param. Value Meaning Basic Exam.1 Exam.2
9
E N D
After dialling 9 to programming tone the Ulydor will hang up.
4.5 System Setting
Param. Value Meaning Basic Exam.1 Exam.2
6# s
number of non-fitted buttons of
basic module
The basic module is fitted with 2 buttons as standard, i.e. s = 0, s = 1 is
set up for the basic module with one button and s = 2 for module without
buttons. This is a factory setting and no service can change this
parameter.
Note: Upon connection to the line the value of this parameter is checked and if
not satisfactory for any reason it is set to s = 0 (for a module fitted with 2
buttons).
30 Ulydor Door Entry Systems – Operating Instructions
4.6 List of Presetting Parameters
Param. Basic Exam. 1 Exam. 2
Relay 1 mode lock m=1 lock m=1 lock m=1
Relay 2 mode lock m=1 camera m=2 prog. m=5
Password Day+Night - Relay1 not 121 4561
Password Day+Night - Relay 2 not 122 4562
Password Day - Relay 1 not not not
Password Day - Relay 2 not not not
Password Night – Relay 1 not not not
Password Night – Relay 2 not not not
Relay 1 active from phone 55 55 55
Relay 2 active from phone 66 66 66
Closing time of switch 1 and 2 5 sec 2 sec 5 sec
Connection of incoming call allowed allowed allowed
Delay between closing first and second relay 10 sec 10 sec 15 sec
Choice DTMF DTMF DTMF
Sign of call extension
* * *
Hanging up from phone 1 / 2 55 / 66 55 / 44 55 / 44
Service password 0000 0000 0000
Switching to day mode 11 11 11
Switching to night mode 10 10 10
Ulydor choice mode 2 groups Day/Night 2 groups
Keypad connection no no on 1st place
Keypad mode dialing Memory nos. dialing
Number of rings of incoming call 2 1 2
Maximum call time 2 min 2 min 1 min
Time between button presses 2 sec 2 sec 2 sec
Time of hanging up when dialling repeated 2 sec 2 sec 2 sec
Time before dialling 1 sec 1 sec 1 sec
Number of rings before hanging up 12 12 12
DTMF tone duration (tone) choice 100ms 100ms 100ms
Gap duration among DTMF tones 100ms 100ms 100ms
Flash duration 100ms 100ms 100ms
Pause duration / interdigit gap 800ms 800ms 800ms
31 Ulydor Door Entry Systems – Operating Instructions
5 TECHNICAL PARAMETERS
5.1 Electrical Parameters
Param. Value Conditions
Minimum line current 18mA line answered
Minimum line voltage 18V line hang up
Voltage on line while Ulydor answers
(VA characteristics)
< 8V
< 12V
I = 20mA
I = 60 mA
Leakage in hang up status < 50uA U = 60V
Impedance of line termination 130R + 820R paral. 220n line answered
Band width 300Hz – 3400 Hz 20 - 60mA
Impedance of ringing > 2Kohm 25 – 60 Hz
Sensitivity of ringing detector min. 10 – 25 V
Pulse choice 40 / 60 ms
Tone choice level 4 a 6 dB 20 – 60 mA
Tone choice sensitivity 40 dB 20 – 60 mA
Sensitivity of tone detector 30 dB 20 – 60 mA
Power supply of lighting, switches and heating 12Vss ± 2V , 10-12Vst ± 2V
Maximum consumption of lighting and heating
300mA 12Vss
Maximum voltage of switch contact
48V at I < 1A
Maximum current of switch contact
2A at U < 30 V
Operational temperature
- 20 to + 50°C
5.2 Mechanical dimensions
Dimensions HxWxD [mm]
Type of Item
1 Module 2 Modules 3 Modules 4 Modules
Surface Mount Box (SMBx) 151 x 157 x 79 241 x 157 x 79 331 x 157 x 79 421 x 157 x 79
Flush Mount Box (FMBB1) 114 x 118 x 45 204 x 118 x 45 294 x 118 x 45 384 x 118 x 45
Flush Mount Box (FMBB2) - 204 x 286 x 45 294 x 286 45 384 x 286 x 45
EWHxx 149 x 151 x 49 241 x 151 x 49 331 x 151 x 49 421 x 151 x 49
Fixing Frame 147 x 151 x 3 239 x 151 x 3 299 x 151 x 3 399 x 151 x 3
32 Ulydor Door Entry Systems – Operating Instructions
6 TABLE OF EASY PROGRAMMING
Complete the section "Your Values" with the values to be programmed.
In double-frame part there are whole programming commands, so the
programming is very simple and without errors.
Meaning Programming Sequence
Description Spec. Par. Complete your values
No. Of
point
Number under button 1
Group 1 – Day
101
16
Number under button 2
Group 1 – Day
102
16
Number under button 3
Group 1 – Day
103
16
Number under button 4
Group 1 – Day
104
16
Number under button 5
Group 1 – Day
105
16
Number under button 6
Group 1 – Day
106
16
Number under button 7
Group 1 – Day
107
16
Number under button 8
Group 1 – Day
108
16
Number under button 9
Group 1 – Day
109
16
Number under button 10
Group 1 – Day
110
16
Number under button 11
Group 1 – Day
111
16
Number under button 12
Group 1 – Day
112
16
Number under button 1
Group 2 – Night
201
16
Number under button 2
Group 2 – Night
202
16
Number under button 3
Group 2 – Night
203
16
Number under button 4
Group 2 – Night
204
16
Number under button 5
Group 2 – Night
205
16
Number under button 6
Group 2 – Night
206
16
Number under button 7
Group 2 – Night
207
16
Number under button 8
Group 2 – Night
208
16
Number under button 9
Group 2 – Night
209
16
Number under button 10
Group 2 – Night
210
16
Number under button 11
Group 2 – Night
211
16
Number under button 12
Group 2 – Night
212
16
Relay 1 works in mode
m=1 – 4
311
1
Relay 2 works in mode
m=1 - 5
312
1
Password for Relay 1
Day+Night
321
6
Password for Relay 2
Day+Night
322
6
Password for Relay 1
Day
331
6
33 Ulydor Door Entry Systems – Operating Instructions
Meaning Programming Sequence
No
. Of
point
Description Spec. Par. Complete your values
Password for Relay 2
Day
332
6
Password for Relay 1
Night
341
6
Password for Relay 2
Night
342
6
Closing of Relay 1 from phone
351
2
Closing of Relay 2 from phone
352
2
Closing time of Relay 1
[sec]
361
2
Closing time of Relay 2
[sec]
362
2
Relay 1 connected by incoming call
1 / 0
371
1
Relay.2 connected by incoming call
1 / 0
372
1
Time between Relays 1 & 2 closing [sec]
38
2
Tone/pulse tone choice 1 / 0
41
1
Sign of call extension
* / # 42
1
Ulydor hanging up from phone 1.
431
2
Ulydor hanging up from phone 2.
432
2
Service password
44
4
Communication to DAY switching
45
2
Communication to NIGHT switching
46
2
Ulydor choice mode 1 / 0
47
1
Keypad connection 0 / 1 / 2
48
1
Keyboard mode 1 / 0
49
1
Number of rings
51
1
Maximum call duration [min]
52
2
Time between button presses [sec]
53
1
Hanging up time before dialling repeated [sec]
54
1
Time before dialling starts [sec]
55
1
Number of rings before system hangs up
56
2
Duration of dialling tone (n+5)x10
57
ms 1
Gap among DTMF tones (n+5)x10
58
ms 1
Recall duration nx100
59
ms 1
Pause duration / interdigit gap nx100
50
ms 1
34 Ulydor Door Entry Systems – Operating Instructions
7 DISTY 300
7.1 Description
The Disty 300 is a DECT-standard cordless
adaptor that when used in conjunction with
a Ulydor PBX enabled door entry system
allows the Ulydor UCx nit to work
cordlessly. The Disty 300 features an
integrated aerial that when used under the
right conditions will provide a range of 30m
indoors and 300m outdoors.
Normally, on a DECT cordless telephone the base can be programmed
with up to six cordless handsets. Effectively the Disty 300 is
programmed as the last of the handsets on the DECT cordless base
station. The UCx module is hardwired to a local Disty 300 (requiring an
RJ11 plug) and when the Ulydor UCx button is depressed by the visitor
the call will be sent to one of the other programmed cordless handsets.
Please be aware that not all DECT cordless handsets support DTMF
signalling and although this will not affect voice communication it could
have an adverse effect on the working of the Ulydor door lock control
and relays.
7.2 Signalling
7.2.1 LED Indication
35 Ulydor Door Entry Systems – Operating Instructions
7.2.2 Tones
7.3 Programming
You can enter the programming mode 20 sec – 10min after power
supply ON by **9 choice (to dial / busy tones) namely after Disty 300
power supply ON. If you had entered a new PIN in previous
programming (par.2) so now you must enter a correct PIN for entry to
programming (following main reset (par. 90) the PIN should not be
entered). The special dialing tone is heard in programming mode. The
entry and correct PIN are confirmed by confirmation tone, the false PIN
by error tone.
Param. Value Meaning
**9
[xxxx]
entry to programming, xxxx=PIN, if entered
0 #
log off – stored DECT parameters will be deleted
1 xxxxxxxx #
entry code to base station (4-8 numbers)
2 xxxx yyyy #
PIN change - xxxx is old, yyyy is new, 0000 is firm one
3 0# - 79#
distance – number load is multiple of 130m (300m = 3)
40
0# / 1#
choice mode - 0
sends / 1 suppresses DTMF choice transmission
from base station (0 is pract. doubled choice)
41
0# / 1#
operational setting - 0 is phone / 1 is FAX
70
0# / 1# / 2#
call limitation - 0 not limited, 1 incoming, 2 outcoming
71
0# / 1# / 2#
type of call - 0 both, 1 internal, 2 external call
72 xxx #
Flash length – xxx times 10ms (100ms = 010) firm.=210ms
90 #
reset and company setting (bold), presets all
91 #
reset and company setting (bold), log in parameters will be kept
92
0# / 1#
autoreset 0-inactive / 1-
active (every 24 hrs will end all transmissions
and recall to base station)
Settings for use with Ulydor: (90#), 401#, 410#, 700#, 710#
36 Ulydor Door Entry Systems – Operating Instructions
Internal call will be executed by **s, where s is 0-9 i.e. number of
internal station, station 9 may be called 10min after power supply ON, up
to this moment it is entry to programming.
Note: The switching of call/internal query can be made by “Flash” and
**s choices. The call will be switched over by hanging up. The “Flash”
function will turn back to previous call.
7.4 Log on to Base Station
The log in might be done automatically in this way that we hold the
button for searching on base station (min 3sec) and then we will connect
the power supply to DistyBox. This will automatically log on to base
station within 1 min and if not made it is recommended to make the
company reset (90#) and repeat logging on. Setting of parameters 401#,
410#, 700#, 710# is required.
Be sure about parameter 40, which is being set after company reset
thus that the choice is transmissed not only by DES, but also the base
station so that the choice is executed twice!!
37 Ulydor Door Entry Systems – Operating Instructions
8 IP CAMERA
IP Camera Rear View of IP Camera
The IP Camera is quick and straight-forward to install via your structured
cable network by adopting the RJ45-RJ45 lead (red lead on the Rear
View photograph) between camera and the wall socket. Programme the
camera via the web, logging its IP address and serial number. Once
accepted file the information under "favourites" on your web browser (or
create a shortcut on your desktop). When receiving a call from the
Ulydor reception unit, simply go into "favourites" (or the shortcut) and by
depressing the appropriate flag your computer screen will 'pop'
displaying the image of the visitor and a conversation can take place.
Loading...