BEDIENUNGSANWEISUNG
mit Montageanweisungen
Instrucciones de Uso y de Montaje
Instructions for use and installation
Instructions d΄utilisation e avis de montage
Instruηυes de uso com indicaηυes para montagem
Instruções de utilização e Instalação
Istruzioni di uso e di montaggio
Bruks- och monteringsanvisningar
Gebruiksaanwijzing en montagehandleiding
Εγχειριδίου µε τις Οδηγίεσ Χρήσεωσ
IKD 11750.0 GE (703043)
(Rev. 0)
14
ENG
Dear client:
Congratulations on your choice. We are sure
that this modern, functional and practical
appliance, made with top quality materials,
will fully satisfy your needs.
Please read every section of this
INSTRUCTIONS MANUAL before using your
kitchen hood for the first time, to ensure
maximum performance from the appliance
and to avoid breakdowns, which may be
caused by incorrect use, as well as to allow
any minor problems to be solved.
Store this manual, as it will provide useful
information about your kitchen hood at all
times and will also help other people to use it.
• Please be aware of current local
regulations with reference to domestic
electrical fittings and gas eduction.
• Verify that the tension and frequency of the
network match those indicated on the label
located inside the kitchen hood.
• THE NET CABLE MUST NOT BE
SUBSTITUTED, EXCEPT BY AN
AUTHORIZED TECHNICAL SERVICE.
• Once the kitchen hood has been installed,
ensure that the mains cable to the network
is not in contact with any live metal edges.
• Avoid connecting the appliance to
conductors used as exits for fumes
produced by a non-electric energy source,
e.g.: boilers, chimneys, etc.
• If the extractor fan is going to be used
simultaneously with equipment powered by
a non-electric energy source, e.g.: gas
cookers, the room must have sufficient
ventilation.
• Excessive fat accumulation in the kitchen
hood and metal filters is a fire risk and may
also cause dripping, therefore the inside of
the kitchen hood and the metal filters must
be cleaned at least once a month.
• The lower part of the kitchen hood must be
fitted at least 50 cm. over electric hobs and
65 cm. over gas or mixed hobs. FOLLOW
THE MANUFACTURER'S MINIMUM
RECOMMENDATIONS.
• Never leave gas hobs lit if not covered by a
container. The fat accumulated in the filters
may drip or catch fire when the
temperature increases.
• Avoid cooking under the kitchen hood if the
metal filters are not fitted, e.g.: while they
are being cleaned in the dishwasher.
• You must not produce flames under the
kitchen hood.
• Disconnect the appliance before any
interior manipulation, e.g. during cleaning
or maintenance.
• We recommend the use of gloves and to
be extremely careful when cleaning the
kitchen hood's interior.
• Your kitchen hood is designed for domestic
use and only for extraction and purification
of fumes produced during food
preparation. It will be your responsibility if it
is used for other purposes, which may be
dangerous. The manufacturer cannot
accept responsibility for damage caused
by improper use of the appliance.
• For repairs please contact the nearest
KÜPPERSBUSCH Technical Assistance
Service, and always use genuine spare
parts. Repairs or modifications carried out
by unqualified personnel can cause
malfunctions or may damage the
appliance, putting your safety in danger.
• This appliance is marked according to the
European directive 2002/96/EC on “Waste
Electrical and Electronic Equipment”
(WEEE). This guideline is the frame of a
European-wide validity of return and
recycling on Waste Electrical and
Electronic Equipment, .
• When the cooker hood is run at the same
time as other than electrical appliance or
equipment with different energy source,
the air extraction (underpressure) must no
be higher than 4Pa (4 x 10
-5
bar).
• The appliance is not intended for use by
young children or infirm persons without
supervision. Young children should be
supervised to ensure they do not play with
the appliance.
Safety Instructions
15
ENG
Index
Page
Description of the appliance 15
Instructions for use 15
Programming timer 15
Cleaning and maintenance 16
Problem solving 16
Sizes and specifications 17
Accessories supplied 18
Installation 18
Active charcoal filters 18
A An electronic programmer device with
TOUCH CONTROL technology to control
speed, light, programming and power
indicators in use as well as filter saturation.
B Metal filters.
C Lamp with two bulbs - 20 W (G-4).
D, E Vertically adjustable tubecovers.
F Decorative part.
G Remote control (Optional).
Switch on the extractor fan a few minutes
before you start to cook in order to ensure that
a steady air flow has been established before
fumes appear.
Allow the extractor fan to run for several
minutes after you have finished cooking
(between 3 to 5 minutes) in order to expel all
the grease from the outlet duct. This prevents
the return of grease, smoke and smells.
Proceed as follows:
1) Turn the kitchen hood on and choose the
required speed. Press "timer". Suction
indicators 1, 2 and 3 will start to flash.
2) Select the required time by pressing the
increase and decrease speed selectors.
There is a variation of 10 in 10 minutes.
(Min.= 10 min.; Max.= 30 min.)
3) Once the required time has been selected,
press "timer" again to memorise the
program. The speed indicator in use will
start to flash.
4)Intensive “H” suction cannot be
programmed as it has a set length of 10
minutes.
Fig. 2 (Page 19)
• Do not mix used batteries with new ones.
• Do not heaten up batteries nor put them
into fire.
• Do not damage nor short-circuit batteries.
• Remove batteries from the remote control
if it will not be used for a longer time. Store
batteries in a dry and cool place.
Clean the filters when the saturation indicator
lights up. (See page 16, Filter cleaning
section).
Once you have cleaned the filters, and with
the hood turned off, press the increase and
decrease speed buttons at the same time for
3 seconds and the indicator will switch itself
off.
Description of the appliance
Instructions for use
Programming timer
You may control the kitchen hood by operating the
controls as shown in the diagram.
Filter saturation indicators
Remote control(Optional)
16
ENG
During cleaning and maintenance work,
make sure the safety instructions set out
on page 14 are complied with.
• If your kitchen hood is made from stainless
steel, use proprietary cleaners mentioned
in the product instructions.
• Never use metallic scourers, nor abrasive
or corrosive products.
• Dry the kitchen hood using a cloth that
does not produce fibres.
• The use of vapour cleaners is not
recommended.
To remove the filters from their fittings, press
lightly on the locks and then pull them off.
The metal filters can be cleaned by soaking
them in hot water with neutral detergent until
the fat dissolves and then rinsing them under
the tap or using special anti-grease products.
They can also be washed in a dishwasher. In
this case, it is advisable to stack them
vertically to avoid food residues to stick to
them.
Cleaning in a dishwasher may damage the
metallic surface (blackening it), although this
will not affect its fat retention capacity.
Once clean, leave them to dry off and then fit
them onto the kitchen hood.
Fig. 1 (Page 19)
Proceed as follows:
• Press the glass upwards and carefully
open downwards until the end stop.
• Unscrew the lamp cap trimming cover.
• Change the broken/ burnt out lamp.
Maximum lamp power is 20 W (G-4).
• Screw in the lamp cap trimming cover.
• Bring the glass back upwards to its initial
position and carefully press for fitting it.
Cleaning and maintenance
_________________________________________________________
Problem solving
Proceed with the following checks before calling the Technical Service:
Cleaning the hood body
Cleaning the metal filters
Changing light bulbs
17
ENG
Sizes and specifications
MIN
815
A
1100
B
700
D
1651115
MAX
C
E
330
F
410
G
760
H
490
A
B
D C
FE
G
H
KÜPPERSBUSCH reserves the right to make changes and corrections to its products as
it deems necessary, without altering their basic characteristics.
* Check Characteristics label inside the hood.
18
ENG
1 150/ 120 mm reduction.
1 Anti-recoil valve.
6 Lock screws (Ø8 x 45).
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
10 are complied with.
To obtain optimum performance, the external
conduct must not be more than FOUR
METRES long, have no more than two 90°
angles and its diameter must be at least Ø120.
1) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
2) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
3) Mount the upper chassis (A6) onto the
support (O) using the screws (Q) (M6 x 16).
4) Place the parts (A+B) if the inner tube (not
supplied) is Ø120.
5) Attach the inner tube with a clamp (not
supplied) to (B) or on to the motor's air outlet
vent as the case may be.
6) Introduce the upper tubecover (A8) into the
lower tubecover (A9).
7) Fit the lower (A9) and upper (A8) tubecover
units onto the lower body (A7) and the
decorative parts (U).
8) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
9) Connect the upper part of the inner tube (not
supplied) to the exit.
10) Raise the upper tubecover (A8) and attach
it to the upper unit with the screws (G) (M4 x
12).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 1 (Page 19)
1) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
2) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
3) Mount the diffuser (A5) with the screws (A4)
(M4 x 12) on to the side rectangles of the upper
body (A6).
4) Mount the upper chassis (A6) onto the
support (O) using the screws (Q) (M6 x 16).
5) Attach the inner tube with a clamp (not
supplied).
6) Introduce the upper tubecover (A8) into the
lower tubecover (A9).
7) Fit the lower (A9) and upper (A8) tubecover
units onto the lower body (A7) and the
decorative parts (U).
8) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
9) Connect the upper part of the inner tube (not
supplied) to the exit.
10) Raise the upper tubecover (A8) and attach
it to the upper unit with the screws (G) (M4 x
12).
11) Press the glass upwards and carefully
open downwards until the end stop. Remove
the metal filters.
12) Put the filters into the lateral draught
section of the motor making the holes in the
filters match up (A11) with the pivots (A12) of
the motor carcass.
13) Place the metal filters. Bring the glass back
upwards to its initial position and carefully
press for fitting it.
Active charcoal filters (Optional)
Installation
Accesories supplied
19
ENG
FIG. 1
FIG. 2
Loading...