Jwin JX-R86 User Manual

DIGITAL VOICE RECORDER

JWIN JX-R86 USER MANUAL

TABLE OF CONTENTS

1. Warnings and instructions

2. Descriptions of the user interface and indications on LCD

3. How to install batteries

4. How to use recording function

5. How to change recording quality (SP, LP)

6. How to change recording sensitivity

7. How to set voice-operated recording (VOR) function

8. How to switch directory to directory

9. How to play a recorded message

10. How to record with other devices (CD / Cassette players)

11. How to record your conversation from a phone call

12. How to check the memory capacity on the recorder

13. How to delete one of the recorded messages

14. How to delete all recorded messages

15. How to set the time and date

16. How to set the alarm function

17. How to set the time-recording function

18. How to use the repeat function

19. How to use the bookmark function

20. How to use the comparison function

21. Additional functions

22. Specification

1. WARNINGS AND INSTRUCTIONS

a. Please do not drop on the floor or put the unit where it can be exposed to high

force impact. This will damage the unit beyond its repairable capacity.

b. Please do not keep this unit in places with extreme heat or cold. Any direct

exposure to extreme temperatures will permanently damage the unit

c. High pressure on the surface of the LCD screen will result in damaging the

message indicators of the screen.

2. DESCRIPTIONS OF USER INTERFACE AND INDICATIONS ON LCD

 INDICATIO NS ON LCD

a. Volume indication
b. Key-lock indication
c. Low battery indication
d. Alarm indication
e. Voice-operated recording (VOR) indication
f. Displaying numbers and symbols
g. Pause indication
h. Recording indication
i. Play indication
j. Recording quality indication
k. Directory indication

 USER INTERFACE OF JX-R86

a. Ext. MIC jack
b. Built-in MIC
c. LED indicator for recording
d. LCD display
e. PLAY / OK key
f. VOL – / Search / Skip backward key
g. VOL + / Search / Skip forward key
h. REC / STOP key
i. REP / POWER key
j. FOL key
k. Built-in speaker
l. Hook for the hand strip
m. Earphone jack
n. Battery compartment

3. HOW TO INSTALL THE BATTERIES

a. Open the battery compartment cover (14).
b. Insert two “AAA” batteries into the compartment according to the polarities

indicated in the compartment.

Note:

Old batteries or weakened batteries may cause quality failure in recording.

4. HOW TO USE RECORDING FUNCTION

a. Press and hold the REC/STOP key for about 2 seconds to enter the recording

mode. You will see the record indication on the LCD display.
b. Press the PLAY/OK key to pause recording while in the recording process.
c. Press the PLAY/OK key again if wish to continue recording while in the pause

mode.
d. Press the REC/STOP key to stop recording.

Note:

The total number of the recorded voice message indicator will increase automatically
by 1

5. HOW TO CHANGE THE RECORDING QUALITY (SP, LP)

a. Press and hold the PLAY/OK key for about 2 seconds to enter the setup mode.
b. Use the VOL + or VOL – key to locate the “SEL COdEC” menu.
c. Press the PLAY/OK key to enter the “SEL COdEC” setup page.
d. Use the VOL + or VOL – key to switch from “SP” to “LP” or from “LP” to “SP”.
e. Press the PLAY/OK key to confirm your choice on the quality selection.
f. Press the REC/STOP key to exit the setup mode completely.

Note:

The SP is used for the high record quality, and the LP is used for the lower record
quality with longer recording time option.

6. HOW TO CHANGE THE RECORDING SENSITIVITY

a. Press and hold the PLAY/OK key for about 2 seconds to enter the setup mode.
b. Use the VOL + or VOL – key to locate the “rEC SENSE” menu.