Jwin JX-CD915 User Manual

JX-CD915

PORTABLE CD/MP3 DISC PLAYER

WITH FM STEREO RADIO

INSTRUCTION MANUAL

ENGLISH

LOCATION OF CONTROLS

1. SKIP / SEARCH DOWN

2. PLAY / PAUSE (POWER ON)

3. LCD DISPLAY

4. ASP / DIR. UP

5. SKIP / SEARCH UP

6. MODE / PROG

7. STOP / (POWER OFF)

8. OPEN KNOB

9. EQ

154

CAUTION

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.

IMPORTANT : Since movement of the CD mechanism and the sensitive circuitry may

cause interference to the radio tuner nearby, switch this unit off while operating other radio devices.

10. DC JACK

11. HOLD SWITCH

12. BATTERY DOOR

13. TUNING KNOB

14. FUNCTION SWITCH

15. HEADPHONE JACK

16. VOLUME

17. BASS BOOST SWITCH

14 15

9876

— 2 — — 3 — — 4 —

PREPARATIONS BEFORE USING

Battery Installation

1. Open Battery Compartment cover.

2. Insert 2 batteries (LR6, “AA” size, or equivalent) in the correct polarity as indicated. (Heavy duty batteries are recommended.)

3. Close the cover properly.

AC Power Adaptor

1. Plug the DC output of the adaptor to the DC Jack.

2. Connect the adaptor (4.5V/600mA) to a power outlet. Make sure the voltage is compatible.

DISC PLAYING

This CD player is designed to play the 8cm and 12cm compact disc without using adaptor.

Hold Switch

Set the HOLD button to “ON” position, all the buttons will be locked. Before operation, be sure to set the switch to “OFF” position, for normal operation.

Getting Start

1. Insert the headphone/earphone plug to PHONE JACK.

2. Set the FUNCTION SWITCH to CD position, Push the OPEN button to right side, and then the door open, put a disc into the CD compartment with label side upward.

3. Push the disc gently around the centre area until it clicks so that the disc fits into the pivot. (To remove the disc : Pick up the disc, holding the edge, while pressing the pivot gently.)

4. Close the door and press the PLAY/PAUSE button once.

5. The Display will show the total number of tracks of the disc and total playing time, then begin to play the first track.

General Operation

Play/Pause Button — Press once to start playback in the original order.

Stop Button — Press once to stop playback.

Skip / Search Buttons — Press once to skip to next track or

ASP / Directory UP Button — ASP ON / OFF (For CD Disc).

Press again to stop the disc play temporarily.

Press again to turn off power

back to previous track .

— Press continuiously to search forward

or backward .

— Directory UP (For MP3 Disc).

Various Playing Modes

MODE Button — There are 3 kind of function :

A. Repeat Play

During PLAY mode

• Press the MODE/PROG button once to play single track repeatedly.

• The repeat indicator will appear in the display. During PLAY mode

• Press the MODE/PROG button twice (Three times in MP3 disc) to play the entire disc repeatedly.

• The repeat indicator will appear in the display.

• Press the MODE button twice in MP3 disc to play the directory repeatedly.

• The repeat indicator DIR will appear in the display.

NOTE - To cancel REPEAT simply press the MODE/PROG button until the repeat indicator

disappears.

B. Random Play

DURING PLAY mode

• Press the MODE/PROG button 3 times. (4 times in MP3 disc)

• The SHUF indicator will appear in the display.

• Press the PLAY button, all the tracks on a disc to be played in a random sequence.

NOTE - To cancel RANDOM PLAY simply press the MODE/PROG button until the SHUF

indicator disappears.

C. Intro Scan

DURING PLAY mode

• Press the MODE/PROG button 4 times. (5 times in MP3 disc)

• The INTRO indicator will appear in the display.

• Press the PLAY button to play the first 10 seconds of each track on the disc.

NOTE - To cancel INTRO SCAN simply press the MODE/PROG button until the INTRO

indicator disappears.

PROGRAM PLAY (FOR CD DISC)

1. In stop mode, press the MODE/PROG button to make program memory.

2. “ PGM 0P -01” will be displayed, “0” means track number to memory and “P-01” means program number. * “0” flashing appears on the display.

3. Press or button to select the desired track.

4. Press the MODE/PROG button to enter the track into memory, the program numbers which will be increment one step. * The program no. “P-01” has become “P-02” on the display.

5. Repeat step 3 and 4 until memory is full.

6. Press button to start the program play.

7. To stop the program play, press the STOP button.

8. For program play in step “ 7 ” , press the MODE/PROG button & button.

9. To erase the program memory, TURN off the power or open the door.

+ 1 hidden pages