JVC KENWOOD V2T001 Users Manual

Warnings, Cautions, and Others

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

For Canada/pour le Canada

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND

For U.S.A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC RF radiation exposure limits set forth  for an uncontrolled environment. To maintain compliance with FCC RF  exposure compliance requirements, please avoid direct contact to the  transmitting antenna during transmitting. This transmitter must not be co-located or operating in conjunction with  any other antenna or transmitter.

Mises en garde, précautions et indications diverses

CAUTION

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

For U.S.A

Declaration of Conformity: Trade Name: JVC Model Number: RX-D301S/RX-D302B

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received,

including interference that may cause undesired operation. Responsible Party: JVC Americas Corp. Address: 1700 Valley Road, Wayne

New Jersey 07470

Telephone Number: 973-317-5000

Caution–– STANDBY/ON button!

Disconnect the mains plug to shut the power off completely. The

STANDBY/ON button in any position does not disconnect the

mains line. The power can be remote controlled.

Attention—Touche STANDBY/ON!

Déconnectez la fiche d’alimentation secteur pour couper l’alimentation complètement. La touche STANDBY/ON, dans n’importe quelle position, ne déconnecte pas le système du secteur. L’alimentation ne peut pas être télécommandé.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

safety_RX-D301S[J]_f.p65 05.2.22, 16:441

For USB wireless transmitter

including interference that may Cause undesired operation.

FCC Radiation Exposure Statement:

For Canada/pour le Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

For Canada/pour le Canada

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

USB Connection

ANTENNA

USB WIRELESS

LEARNING

IDON

USB

USB WIRELESS TRANSMITTER

IDCHANNEL

POWER PLAYERID

USB WIRELESS TRANSMITTER

POWER PLAYERID

USB WIRELESS TRANSMITTER

This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA terminal on the rear. You can enjoy sound reproduced through your PC with either of the following methods: 1 connecting a USB wireless antenna (supplied) to the USB

WIRELESS ANTENNA terminal and a USB wireless transmitter (supplied) to your PC. (USB WIRELESS)

2 connecting your PC to the USB terminal with a USB cable (not

supplied). (USB TERMINAL) When you connect your PC for the first time, follow the procedure below.

• Remember you cannot send any signal or data to your PC from

this receiver.

• Use USB extension cable (supplied) if it is difficult to connect

the transmitter directly to the USB connector or the transmitter becomes obstacle to other USB connectors.

IMPORTANT:

• Check if your PC equipped with the CD-ROM drive is running

on Windows® 98 SE*, Windows® Me*, Windows® 2000* or Windows® XP* and prepare its CD-ROM.

• Check your PC’s BIOS setting—whether USB is available, and

whether USB IRQ is set to “AUTO” or to available IRQ number.

Preparation

1 (For USB WIRELESS)

Be sure to make this procedure after purchasing the receiver.

1. Connect the antenna to the USB WIRELESS ANTENNA

terminal on the rear panel.

• Tighten the screw with the antenna upright.

USB wireless

antenna

(supplied)

2. Turn on your PC.

• If the PC has been turned on, quit all the applications now running.

3. Connect the USB wireless transmitter to the USB connector of the PC.

Before connecting the transmitter to the PC, remove the cover of the transmitter. When you connect the transmitter, the USB drivers are installed. The POWER and PLAYER lamp on the transmitter light up.

4. Turn on the receiver, then slide the USB WIRELESS switch on the rear to “ID LEARNING,” and select the source as “USB WIRELESS.”

When you slide the switch, the lamp in the switch starts flashing.

5. Set the volume to minimum.

IMPORTANT:

Always set volume to “0” when connecting or disconnecting the other equipment.

6. Press and hold ID on the transmitter to make a wireless communication with the receiver.

When you press and hold the button, the ID lamp on the transmitter flashes.

When the receiver recognizes the transmitter, the “L” and “R” indicators (see page 16) light up on the display. The lamp on the rear stops flashing and lights up.

7. Slide the switch on the receiver to “ON.”

• If you do not, no sound signal is transmitted to the receiver.

NOTES

• The signal-reachable distance is about 30 m (100 ft.), but it may

differ depending on the operating conditions and circumstances.

• The PLAYER lamp on the transmitter keeps flashing when

starting the playback software in your PC.

• If no signals are transmitted from the transmitter for about 30

minutes, the transmitter enters “sleep” mode. The “L” and “R” indicators go off from the display.

• Though the transmitter may become hot, it is not a malfunction.

2 (For USB TERMINAL)

1. Turn on your PC.

• If the PC has been turned on, quit all the applications now

running.

2. Turn on the receiver, and select the source as “USB TERMINAL.”

3. Set the volume to minimum.

IMPORTANT:

Always set volume to “0” when connecting or disconnecting the other equipment.

4. Connect the receiver to the PC using a USB cable (not supplied).

USB wireless

transmitter (supplied)

11-13D301J2.p65 05.2.23, 18:3012

USB cable (not supplied)

• Use “USB series A plug to B plug” cable when connecting.

+ 3 hidden pages