JVC KENWOOD 452501 Users Manual

TKR-D710 TKR-D810

VHF DIGITAL REPEATER

UHF DIGITAL REPEATER

INSTRUCTION MANUAL

B5A-1121-00 (K)

VHF DIGITAL REPEATER/ UHF DIGITAL REPEATER

TKR-D710/ TKR-D810

INSTRUCTION MANUAL

THANK YOU!

We are grateful you purchased this KENWOOD repeater. We believe this easy-to-program repeater will be highly eﬀ ective in your communications system, and will keep personnel operating at peak eﬃ ciency.

◆

Do not install the repeater in explosive atmospheres (inﬂ ammable

gas, dust particles, metallic powders, grain powders, etc.).

PRECAUTIONS

• Do not expose the unit to rain or moisture; to prevent ﬁ re or electric shock.

• Do not open the unit under any circumstances; to avoid risk of electric shock.

• Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances.

• Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces.

•

Do not put the plastic bag used for packing of this equipment on the place which reaches a small child's hand. It will become a cause of suffocation if it wears ﬂ atly.

•

Always switch the transceiver power off before installing optional accessories.

• If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your

KENWOOD service center or dealer.

NOTICES TO THE USER

Government law prohibits the operation of unlicensed radio

◆

transmitters within the territories under government control.

Illegal operation is punishable by ﬁ ne and/or imprisonment.

◆

Refer service to qualiﬁ ed technicians only.

◆

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modiﬁ cations to this equipment may cause harmful interference unless the modiﬁ cations are expressly approved by the party responsible/JVC KENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modiﬁ cation is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to

•

which the receiver is connected.

Consult the dealer for technical assistance.

•

Firmware Copyrights

The title to and ownership of copyrights for ﬁ rmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation.

This repeater is intended for use as a ﬁ xed base station with

◆

the antenna located outdoors on the rooftop or on an antenna tower.

This repeater is designed for a 13.6 V DC power source!

◆

Never use a 24 V DC or higher source to power the repeater.

Use only the supplied DC cord.

◆

Do not remove the ferrite core attached to the DC cord. Doing

◆

so may cause interference with radio communications.

UNPACKING AND CHECKING EQUIPMENT

Note:

The following unpacking information is for use by your

KENWOOD

factory.

dealer, an authorized

KENWOOD

service center, or the

Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, ﬁ le a claim with the carrier immediately.

Item Part Number Quantity

Hardware ﬁ xture Front glass Name plates Cushion Cushion Foot Foot Grommet Handle Screws Screws DC cord Lead wire with connector (15 pin) Fuse Instruction Manual

J21-8559-XX 1 B10-2635-XX 1 B11-1259-XX 1 G13-1801-XX 4 G13-1802-XX 4

J02-0475-XX 2

J02-0492-XX 2

J59-0302-XX 2 K01-0418-XX 1 N30-4006-XX 2 N35-3006-XX 5 E30-3427-XX 1 E31-3228-XX 1 F05-1537-XX 1 B5A-1121-XX 1

INSTALLATION

To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws.

Please consult your dealer for installing the repeater and antenna.

The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and #8,359,197.

+ 4 hidden pages