JVC KENWOOD 417101 Users Manual

NXR-900/ NXR-901

800MHz DIGITAL BASE-REPEATER/ 900MHz DIGITAL BASE-REPEATER

INSTRUCTION MANUAL

BASE-RELAIS NUMÉRIQUE 800MHz/ BASE-RELAIS NUMÉRIQUE 900MHz

MODE D'EMPLOI

BASE-REPETIDOR DIGITAL 800MHz/ BASE-REPETIDOR DIGITAL 900MHz

MANUAL DE INSTRUCCTIONES

NXR-900/ NXR-901 INSTRUCTION MANUAL

800MHz DIGITAL BASE-REPEATER/ 900MHz DIGITAL BASE-REPEATER

THANK YOU!

We are grateful you purchased this

KENWOOD

believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency.

KENWOOD

incorporates the latest in advanced technology into all of our products. As a result, we feel strongly that you will be pleased with the quality and features of this product.

PRECAUTIONS

• Do not expose the unit to rain or moisture; to prevent fire or

electric shock.

• Do not open the unit under any circumstances; to avoid risk

of electric shock.

• Do not expose the unit to long periods of direct sunlight, nor

place it close to heating appliances.

• Do not place the unit in excessively dusty and/or humid

areas, nor on unstable surfaces.

• If you detect an abnormal odor or smoke coming from the

unit, disconnect the power from the unit immediately. Contact your

KENWOOD

service center or dealer.

NOTICES TO THE USER

Government law prohibits the operation of unlicensed radio

◆

transmitters within the territories under government control.

Illegal operation is punishable by fine and/or imprisonment.

◆

Refer service to qualified technicians only.

◆

repeater. We

This repeater is intended for use as a fixed base station with

◆

the antenna located outdoors on the rooftop or on an antenna tower. (except USA and Canada)

This repeater is designed for a 13.8 V DC power source!

◆

Never use a 24 V DC or higher source to power the repeater.

Use only the supplied DC cord.

◆

Do not remove the ferrite core attached to the DC cord. Doing

◆

so may cause interference with radio communications.

UNPACKING AND CHECKING EQUIPMENT

The following unpacking information is for use by your

Note: KENWOOD

factory.

Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately.

Front glass B10-2781-XX 1 Dressed screw N08-0563-XX 1 Bracket J29-0725-XX 2 Flat head machine screw N32-4008-XX 4 Handle and screw set K01-0421-XX 1 DC cord E30-3344-XX 1 Lead wire with connector (15 pin) E37-1381-XX 1 Fuse (7.5 A) F05-7521-XX 1 SYNC Cable E30-7701-XX 1 Instruction Manual B62-2410-XX 1

dealer, an authorized

KENWOOD

service center, or the

Item Part Number Quantity

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to

•

which the receiver is connected. Consult the dealer for technical assistance.

•

INSTALLATION

To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws.

Please consult your dealer for installing the repeater and antenna.

MICROPHONE

Connect an optional KMC-30, KMC-35, or KMC-9C microphone to the

MICROPHONE

jack on the front panel.

KENWOOD

OCXO UNIT (KXK-3):Option

The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator (OCXO) unit.

+ 4 hidden pages