JVC KENWOOD 35753110 User Manual

INSTRUCTION MANUAL

GRP

POWER

VOL

BUSY

SCAN OPT OSTA B CMON

CALL

MON

SCN

GRP

VOL

POWER

BUSY

VHF FM TRANSCEIVER

TK-5710 series

THANK YOU!

We are grateful you chose KENWOOD for your land mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency.

KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product.

MODELS COVERED BY THIS MANUAL

••

•TK-5710:VHF FM Transceiver

••

•TK-5710H:VHF FM Transceiver

••

NOTICES TO THE USER

◆

GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL.

◆

ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH.

◆

REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.

SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.

WARNING!

◆

EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)

Turn OFF your transceiver while taking on fuel or while parked in a gasoline service station. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area.

◆

INJURY FROM RADIO FREQUENCY TRANSMISSIONS

Do not operate your transceiver when somebody is within two to three feet of the antenna, to avoid the possibility of radio frequency burns or related physical injury.

◆

DYNAMITE BLASTING CAPS

Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. Operating the transceiver within 150 meters (500 feet) of dynamite blasting caps may cause them to explode. If you are carrying blasting caps in your vehicle, make sure they are enclosed in a metal box with a padded interior. Do not transmit while the caps are being placed into or are being removed from the container.

Note:

This instruction manual covers only the basic functions of the transceiver. Consult your dealer

for more detailed information.

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer for technical assistance.

PREPARATION

WARNING!

◆

VARIOUS ELECTRONIC EQUIPMENT IN YOUR VEHICLE MAY MALFUNCTION IF THEY ARE NOT PROPERLY PROTECTED FROM THE RADIO FREQUENCY ENERGY WHICH IS PRESENT WHILE TRANSMITTING. ELECTRONIC FUEL INJECTION, ANTI-SKID BRAKING, AND CRUISE CONTROL SYSTEMS ARE TYPICAL EXAMPLES OF EQUIPMENT THAT MAY MALFUNCTION. IF YOUR VEHICLE CONTAINS SUCH EQUIPMENT, CONSULT THE DEALER FOR THE MAKE OF VEHICLE AND ENLIST HIS AID IN DETERMINING IF THEY WILL PERFORM NORMALLY WHILE TRANSMITTING.

◆

ALTHOUGH THE REMOTE PANELS ARE WATER RESISTANT, THE MAIN TRANSCEIVER BODY IS NOT. MOUNT IT IN A PLACE WHERE IT WILL NOT GET WET.

Note:

The following preparation instructions are for use by your

KENWOOD

service facility, or the factory.

■ Tools Required

Note

: Before installing the transceiver, always check how far the mounting screws will extend below the mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts.

The following tools are required for installing the transceiver:

• 6 mm (1/4 inch) or larger electric drill

• Drill bits (sizes listed below) and circle cutters

eziStiBllirD esopruP

)hcni23/5(mm2.4swercsgnippat-flesmm61x5

)hcni8/1(mm2.3swercsgnippat-flesmm61x4

KENWOOD

dealer, an authorized

■ Power Cable Connection

CAUTION:

CHECK THE BATTERY POLARITY AND VOLTAGE OF THE VEHICLE BEFORE INSTALLING THE TRANSCEIVER.

THE TRANSCEIVER OPERATES IN 12 V NEGATIVE GROUND SYSTEMS ONLY!

1 Check for an existing hole, conveniently located in the firewall, where the

power cable can be passed through.

• If no hole exists, use a circle cutter to drill the firewall, then install a rubber grommet.

2 Run the two power cable leads through the fire wall and into the engine

compartment, from the passenger compartment.

3 Connect the red lead to the positive (+) battery terminal and the black lead

to the negative (–) battery terminal.

• Locate the fuse as close to the battery as possible.

4 Coil and secure the surplus cable with the provided retaining band.

• Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied.

■ Installing the Transceiver

WARNING!

SUPPLIED MOUNTING BRACKET, SO THE TRANSCEIVER WILL NOT BREAK LOOSE IN THE EVENT OF A COLLISION.

FOR PASSENGER SAFETY, INSTALL THE TRANSCEIVER SECURELY, USING THE

1 Mark the position of the holes in the dash by using the mounting bracket

as a template. Drill the holes, then attach the mounting bracket using the supplied 5 x 16 mm screws.

• Be sure to mount the transceiver in a location where the controls will be within easy reach of the user, and where there is sufficient space at the rear of the transceiver for cable connections.

2 Connect the antenna and the supplied power cable to the transceiver.

3 Slide the transceiver into the mounting bracket and secure it using the

supplied hex-headed screws.

4 Mount the microphone hanger, using the supplied 4 x 16 mm screws, in a

location where it will be within easy reach of the user.

• The microphone and microphone cable should be mounted in a place where they will not interfere with the safe operation of the vehicle.

5 Connect one plug of the microphone cable to the jack on the base of the

microphone, and the other plug to the microphone jack on the front panel of the transceiver. Place the microphone on the hanger.

Microphone

hanger

Mounting bracket

Microphone cable

Power input

connector

Antenna

connector

Power cable

Transceiver

Red wire

Black wire

Fuse

Fuse holder

Hex headed

screw

Battery

GETTING ACQUAINTED

■ Basic Front Panel (KCH--14)

POWER

GRP

BUSY

VOL

q POWER switch

!0!0

!1!1

Press to switch the power ON (or OFF).

w GRP (Group) keys

Press GRP Up to increase the group selection by one step. Press GRP Down to decrease the group selection by one step. (See page 11 for

other programmable functions for these keys.)

e TX, BUSY indicators

The TX (red) indicator lights while transmitting. The BUSY (green) indicator lights while the selected channel is in use.

r Microphone connector

Insert the microphone plug into this connector and secure it using the attached screw. To remove the microphone, release the screw, then turn the connector clockwise until it becomes free.

t VOL (Volume) control

Turn clockwise to increase the volume, and counterclockwise to decrease it.

y CH (Channel) control

Turn clockwise to increase the channel selection (default setting), and counterclockwise to decrease it. (Alternatively, this control can be programmed with group up/down.)

u PF1 key

uu ii

i PF2 key

ii oo

o PF3 key

oo !0!0

!0 PF4 key

!0!0 !1!1

!1 PF5 key

!1!1

Press these PF (programmable function) keys to activate their programmable functions {page 11}. The default is set as No Function.

■ Basic Panel Display

!0!0

!1!1

!2!2

!3!3

qqqqq

wwwww

eeeee

rrrrr

ttttt

yyyyy

uuuuu

iiiii

eht,rebmunlennahC/puorGgnitarepoehtsyalpsiD

.sutatsreviecsnartehtdna,emanlennahC/puorG

.rebmunlennahcropuorggnitarepoehtsyalpsiD

:sutatslennahcehtsyalpsidoslA 1P asetacidni

;lennahc1ytiroirP 2P ;lennahc2ytiroirPasetacidni

PP ;lennahc2dna1ytiroirPasetacidni CH ;lennahCemoHasetacidni At klaTsetacidni

;edomdnuorA LCr ;lennahCllaceRasetacidni

1r ~ 51r .slennahcetomersetacidni

enoT-2roFMTDybdeviecersillacanehwsehsalF

fignittimsnartretfadnagnirudsraeppA.gnilangis

.relaedehtybtes

gninnacsehtnisipuorgdetcelesehtnehwsraeppA

”itluM“ottesneebsahnacspuorgfiecneuqes

.)nacsehtgnittesrofrelaedruoytlusnocesaelp(

.FFOdenrutsihcleuqsgnilangisnehwsraeppA

.ssergorpnisigninnacselihwsraeppA

.rekaepsAPottessituptuooiduanehwsraeppA

sidraobrelbmarcslanoitpoehtnehwsraeppA

.delbane

ooooo

.ecneuqesgninnacs

0!0!0!0!0!

1!1!1!1!1!

2!2!2!2!2!

3!3!3!3!3!

.delbane

.NOsiAxuAnehwsraeppA

.NOsiBxuAnehwsraeppA

.NOsiCxuAnehwsraeppA

ehtnisilennahcdetcelesehtnehwsraeppA

sienoTelbatceleSrotarepOnehwsraeppA

+ 14 hidden pages