JVC XV-N30BK(MK3), XV-N33SL(MK3), XV-N35SL(MK3), XV-N3SL(MK3) User Manual

DVD VIDEO PLAYER

XV-N30BK/XV-N33SL

Before operation 2

Preparations 3

Basic operations 6

Advanced operations 11

MP3 disc playback 19

VIDEO

INSTRUCTIONS

Changing the initial settings 21

Additional information 26

For Customer Use:

Enter below the Model No. and Serial No.
which are located on the rear, bottom or
side of the cabinet. Retain this information
for future reference.

Model No.

Se ria l No

GNT0024-001D

[J/UJ]

Warnings, Cautions and Others

Mises en garde, précautions et indications diverses

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

For U.S.A.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de
l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

Caution –– STANDBY/ON button!

Disconnect the mains plug to shut the power off completely. The
STANDBY/ON
mains line. The power can be remote controlled.

Attention –– Touche STANDBY/ON

Déconnecter la fiche de secteur pour couper complètement le courant.
La touche STANDBY/ON
de secteur, quelle que soit sa position. Le courant peut être
télécommandé.

button in any position does not disconnect the

!

ne coupe jamais complètement la ligne

IMPORTANT FOR LASER PRODUCTS
IMPORTANT POUR LES PRODUITS LASER

1. CLASS 1 LASER PRODUCT

2. DANGER: Visible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

3. CAUTION: Do not open the top cover. There are no user service-

able parts inside the Unit; leave all servicing to qualified service
personnel.

1. PRODUIT LASER CLASSE 1

2. ATTENTION: Radiation laser visible quand l'appareil est ouvert ou

que le verrouillage est en panne ou désactivé. Eviter une exposition
directe au rayon.

3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n'y a aucune

pièce utilisable à l'intérieur. Laisser à un personnel qualifié le soin
de réparer votre appareil.

WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

For Canada/pour le Canada

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND

For Canada / Pour le Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FORM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES­003 OF THE DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS
RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR: “APPAREILS NUMERIQUES”,
NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.

CAUTION:

• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on
the apparatus.

• When discarding batteries, environmental problems must be consid­ered and local rules or laws governing the disposal of these batteries
must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing
and that no objects filled with liquids, such as vases, shall be placed
on the apparatus.

ATTENTION

• Ne bloquez pas les orifices ou les trous de ventilation.
(Si les orifices ou les trous de ventilation sont bloqués par un journal
un tissu, etc., la chaleur peut ne pas être évacuée correctement de
l’appareil.)

• Ne placez aucune source de flamme nue, telle qu’une bougie, sur
l’appareil.

• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut des
piles.

• N'exposez pas cet appareil à la pluie, à l'humidité, à un égouttement
ou à des éclaboussures et ne placez pas des objets remplis de liquide,
tels qu'un vase, sur l'appareil.

G-1

Supplied accessories

Check that you have all the following accessories supplied to you.
If anything is missing, consult your dealer immediately.

• Audio/video cable (Yellow/White/Red) (× 1)

• Remote control unit (× 1)

• Lithium battery CR2032 (× 1)

• AC power plug adaptor (×1) (for PX model ONLY)

Table of contents

Supplied accessories................................................................1

About this manual.....................................................................1

Precautions ................................................................................1

Before operation................................................... 2

About discs .............................................................................. 2

About this manual

• The display window information and OSD (On Screen Display)
menu items are put in brackets [ ] in the operation procedures.

• Usable disc(s) for each operation/function is (are) referred to by
the icons;

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet. A small
amount of power (0.7 W) is always consumed while the power
cord is connected to the wall outlet.

• When unplugging the unit from the wall outlet, always pull the
plug, not the power cord.

• Do not handle the power cord with wet hands!

Avoid moisture, water and dust

• Do not place the unit in moist or dusty places.

• If water gets inside the unit, turn off the power and remove the
plug from the wall outlet, then consult your dealer. Using the
unit in this state may cause a fire or electrical shock.

Avoid high temperatures

• Do not expose the unit to direct sunlight or place it near a
heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too
cold between 5°C and 35°C (41°F and 95°F).

• Leave sufficient distance between the unit and the TV.

• Do not install the unit in a place subject to vibrations.

To prevent malfunction of the unit

• There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.

• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the unit.

• Do not block the vents. Blocking the vents may damage the unit.

To clean the cabinet

• Use a soft cloth. Follow the relevant instructions on the use of
chemically-coated cloths.

• Do not use benzene, thinner or other organic solvents and
disinfectants. These may cause deformation or discoloring.

Preparations ......................................................... 3

Connections.............................................................................3

Using the remote control unit...................................................5

Basic operations .................................................. 6

Turning on/off the unit..............................................................6

Initial setup ..............................................................................6

Basic playback.........................................................................7

Resuming playback .................................................................8

Various speed playback ..........................................................9

Locating the beginning of a scene or song ............................10

Advanced operations......................................... 11

Playing from a specific position .............................................11

Changing the playback order.................................................12

Repeat playback ....................................................................14

Changing the language, sound and scene angle ..................15

Special picture/sound effect ..................................................16

Menu bar functions ................................................................17

MP3 disc playback ............................................. 19

Operations .............................................................................19

Changing the initial settings ............................. 21

Selecting preferences ............................................................21

Limiting playback by children.................................................24

Additional information ....................................... 26

Names of parts and controls..................................................26

Troubleshooting.....................................................................28

Specifications ........................................................................28

Appendix A: Country/Area code list for Parental Lock........... 29

Appendix B: Table of languages and their abbreviations ......30

Appendix C: Digital output signal chart..................................30

Appendix D: Glossary ............................................................31

1

B

e

f

o

r

e

o

p

e

r

a

t

i

o

n

Before operation

About discs

Playable disc types

Discs with the following marks can be played back on the unit.

DVD VIDEO SVCD Video CD

VIDEO

The DVD Logo is a trademark.
The unit can also play back the following discs:

• DVD-R and DVD-RW discs written in the DVD VIDEO format
and finalized

• CD-R and CD-RW discs written in the SVCD, Video CD or
Audio CD format and finalized

• CD-R and CD-RW discs written in MP3 in accordance with the
“ISO 9660” format (See page 19 for details.)

NOTE

If a disc gets dirty, scratched or warped, or due to the disc
characteristics or recording conditions, it may take considerable
time for the unit to read the content, or the unit may not be able to
play back such discs.

The unit can play back audio signals recorded in MIX-MODE CD,
CD-G, CD-EXTRA and CD TEXT.

Region code of DVD VIDEO

This unit can play back DVD VIDEO discs whose region code
numbers include “1.”

Examples of playable DVD VIDEO discs:

Audio CD

Digital audio formats

The unit supports the following digital audio formats (see page 31
“Glossary” for descriptions of each audio format):

Linear PCM, Dolby Digital, DTS (Digital Theater Systems)

NOTES

• Depending on the unit’s [DIGITAL AUDIO OUTPUT] setting,
digital audio signals may not be output as they are recorded on
the disc. See “DIGITAL AUDIO OUTPUT” on page 23 for
details.

• To play back DTS-encoded DVD VIDEO or DTS-encoded Audio
CD discs correctly, connect the unit to an amplifier with a built-in
DTS decoder. If the unit is connected to an amplifier without a
DTS decoder, playback sound will be distorted.

Notes on discs

• With some DVD VIDEO discs, the unit starts playback
automatically after inserting the disc.

• The image may be sometimes poor or noisy due to defects in
the disc itself.

• With some discs, operations described in this manual may not
be possible.

Care and handling of discs

If a disc gets dirty, dusty, scratched or warped, playback sound
and picture may be deteriorated. Take proper precautions when
handling discs.

Handling

• Do not touch the surface of the disc.

• Do not damage, stick paper to, or use any adhesive on either
the label side or playback side.

2

ALL

NOTE

The unit’s region code is printed on the rear of the unit.

1

51

1

4

3

Color system format

This unit accommodates the NTSC system, and also can play
back discs recorded with PAL system whose Region Code
numbers include “1.”
Note that the PAL video signal on a disc is converted to an NTSC
signal and output.

Unplayable discs

The unit does not play back discs listed below. If you try to play
back these discs, noise may generate causing damage to
speakers.

• DVD-RW discs written in the VR format

• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM, PHOTO CD,
SACD

In addition, the unit does not play:

• Unfinalized discs

• Discs of irregular shape or discs with tape, seals or paste on
either the label side or playback side. Playing back these discs
may damage the unit.

2

2

3

1

5

6

4

Storing discs

• Keep discs in their cases. If discs are piled on top of one
another without their protective cases, they can be damaged.

• Do not put discs in a location where they may be exposed to
direct sunlight, or where the humidity or temperature is high.
Avoid leaving discs in a car!

Cleaning discs

• Wipe with a soft dry cloth, moving from the center outwards. If a
disc is difficult to clean, wipe with a cloth moistened with water.

• Never use record cleaners, petrol, alcohol or any anti-static
agents.

Notes on copyright

Check the copyright laws in your country before recording from
DVD VIDEO, SVCD, Video CD, Audio CD and MP3 discs.
Recording of copyrighted material may infringe copyright laws.

This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.

Preparations

R

IG

H

T

LE

FT

C

O

A

XIA

L

V

ID

EO

S-VID

E

O

YP

B

P

R

O

P

TIC

A

L

P

C

M

/S

T

R

E

A

M

C

O

M

P

O

N

E

N

T

V

ID

E

O

O

U

T

V

ID

E

O

O

U

T

A

U

D

IO

O

U

T

D

IG

IT

A

L

O

U

T

RIG

H

T

LEF

T

C

OA

X

IAL

V

IDEO

S-VID

E

O

Y

P

B

P

R

O

PTIC

A

L

P

C

M

/S

T

R

E

A

M

C

O

M

P

O

N

E

N

T

V

ID

E

O

O

U

T

V

ID

EO

O

U

T

A

U

D

IO

O

U

T

D

IG

IT

A

L

O

U

T

R

IG

H

T

LEFT

C

OA

XIA

L

V

ID

E

O

S-VID

E

O

YP

B

P

R

O

P

TIC

AL

P

C

M

/S

T

R

E

A

M

C

O

M

P

O

N

E

N

T

V

ID

E

O

O

U

T

V

ID

E

O

O

U

T

A

U

D

IO

O

U

T

D

IG

IT

A

L

O

U

T

Connections

Before using the unit, connect the unit to a TV and/or amplifier.

Before making connections

• Do not connect the AC power cord until all other
connections have been made.

• Connect VIDEO OUT of the unit directly to the video input
of your TV. Connecting VIDEO OUT of the unit to a TV via a
VCR may cause a monitor problem when playing back a
copy-protected disc. You may also have a monitor problem
when connecting the unit to an integrated TV/Video
system.

• In the following description, “TV” may be substituted with

“monitor” or “projector.”

• Terminal names used for other components may be different

from those used in the following description.

Connecting to a TV

The following sections A to C describe TV connections where
only a TV is connected to the unit so that you will hear audio from
the TV.

A Connecting to a conventional TV

B Connecting to a TV with an S-video jack

If your TV has an S-VIDEO input, you can get better picture
quality by connecting it with the S-VIDEO output of the unit using
an S-video cable instead of connecting the video input of the TV
to the VIDEO jack of the unit.

TV

The unit

S-VIDEO

VIDEO

F

E

L

AUDIO

H

IG

R

IN

White

Red

T

T

White

Red

Audio cable (not supplied)

S-video cable (not supplied)

Preparations

TV

VIDEO

E

L

AUDIO

IG

R

IN

T

F

T

H

Yellow

White

Red

The unit

White

Yellow

Red

Audio/video cable (supplied)

NOTE

If your TV has a monaural audio input instead of stereo, you need
to use an optional audio cable which converts stereo audio output
to monaural.

NOTE

When using the S-VIDEO output jack, do not connect the
COMPONENT VIDEO OUT jacks on the unit.

C Connecting to a TV with component jacks

You can enjoy picture of high-fidelity color reproduction by
connecting the COMPONENT VIDEO OUT jacks on the unit to
your TV.

TV

The unit

S-VIDEO

VIDEO

F

E

L

AUDIO

H

IG

R

IN

T

T

Y

P

M

O

C

White

B

P

T

N

E

N

O

Red

White

Red

Audio cable (not supplied)

Component video cable (not supplied)

R

P

IN

Red

Blue

Green

Red

Green

Blue

NOTES

• Connect “Y” to “Y,” “PB” to “PB” (CB), “PR” to “PR” (CR) correctly.

• When using the COMPONENT VIDEO OUT jacks, do not
connect the S-VIDEO output jack on the unit.

• When the component video input jacks on the TV are of the
BNC type, use an adapter to convert a pin jack to a BNC jack
(not supplied).

3

Preparations

Preparations

RIG

H

T

LEF

T

C

OA

X

IA

L

V

ID

EO

S-VIDE

O

Y

P

B

P

R

OP

T

IC

AL

P

C

M

/S

TR

E

A

M

C

O

M

P

O

N

E

N

T

V

ID

E

O

O

U

T

V

ID

E

O

O

U

T

A

U

D

IO

O

U

T

D

IG

IT

A

L

O

U

T

RIGH

T

L

E

FT

CO

AX

IA

L

V

ID

EO

S-VID

E

O

Y

P

B

P

R

O

P

T

IC

AL

P

C

M

/S

T

R

E

A

M

C

O

M

P

O

N

E

N

T V

ID

E

O

O

U

T

V

ID

E

O

O

U

T

A

U

D

IO

O

U

T

D

IG

IT

A

L

O

U

T

Connecting to optional audio equipment

Connecting to a stereo audio amplifier/receiver

Connect the unit’s AUDIO OUT (LEFT/RIGHT) jacks to any line­level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier or
receiver.

Amplifier or receiver

IN

T

F

E

L

DVD

T

H

IG

R

White

Red

The unit

White

Red

Connecting to a digital audio device

You can enjoy sound of enhanced quality by connecting the unit’s
DIGITAL OUT (either OPTICAL or COAXIAL) jack to a digital
input of an amplifier, etc., using an optical or coaxial digital cable.
The digital audio signal on a disc will be transferred directly from
the unit. If the connected digital audio equipment is a Dolby
Digital or DTS decoder or an amplifier with a built-in decoder, you
can enjoy high-quality surround sound.

NOTE

Sound recorded on DTS-encoded DVD VIDEO or DTS-encoded
Audio CD discs are not output from the analog (AUDIO OUT
LEFT/RIGHT) jacks of the unit.

Audio cable (not supplied)

NOTES

• Connect the unit and the digital audio device by using either an
optical digital cable or a coaxial digital cable.

• It is not recommended to use the digital jacks for dubbing.
When recording the sounds (DVD VIDEO, SVCD, Video CD or
Audio CD) played back on the unit, record them through the
analog jacks.

• Depending on the disc, no signal may be output from the
DIGITAL OUT. Make an analog connection in this case.

• Set [DIGITAL AUDIO OUTPUT] in the [AUDIO] preference
display correctly according to the connected digital audio
equipment. If setting made for [DIGITAL AUDIO OUTPUT] is
incorrect, loud noise may be generated causing damage to
the speakers (see page 23).

Digital equipment

IN

L

A

IC

T

P

O

IN

DIGITAL

L

IA

X

A

O

C

Coaxial digital cable
(not supplied)

When using the DIGITAL OUT
(OPTICAL) jack, remove the

T

F

E

L

DVD

T

H

IG

R

protection cap. Do not lose the
removed cap.
When the DIGITAL OUT
(OPTICAL) jack is not used,
replace the protection cap in the
jack.

Optical digital cable
(not supplied)

Audio cable (not supplied)

The unit

4

Preparations

Connecting the power cord

When all the audio/video connections have been made, connect
the AC power plug to the wall outlet. Make sure that the plugs are
inserted firmly.
The STANDBY indicator lights in red.

NOTE

(only for PX model)
Use the supplied AC power plug adaptor when inserting the
larger plug to the wall outlet.

Warning

• Disconnect the power cord:

- if you are not going to use the unit for a long time.

- before cleaning the unit.

- before moving the unit.

• Do not:

- connect or disconnect the power cord with wet hands.

- pull the power cord when disconnecting it, as this may
damage the cord and cause fire, electric shock, or other
accidents.

Caution

• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.

Precautions of the safe use of battery

• Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a doctor
immediately.

• Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
Doing any of these things may cause the battery to give off
heat, crack, or start a fire.

• Do not leave the battery with other metallic materials.
Doing this may cause the battery to give off heat, crack, or start
a fire.

• When throwing away or saving the battery, wrap it in tape and
insulate; otherwise, the battery may start to give off heat, crack,
or start a fire.

• Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to give off heat, crack, or start
a fire.

• Dispose of batteries in the proper manner, according to federal,
state, and local regulations.

Remote sensor

Point the top of the remote control unit toward the remote sensor
as directly as possible. If you operate it from a diagonal position,
the operating range (approx. 5 m) may be shorter.

Remote sensor

Preparations

Using the remote control unit

To install battery

1 While pushing the lock lever (1), pull out the

battery holder (2).

2 Place the supplied battery on the battery

holder with the + side facing up.

Lithium coin battery
(product number: CR2032)

3 Insert the battery holder back into position.

5

Basic

operati

ons

Basic operations

STANDBY indicator

730

STANDBY/ON

STANDBY/
ON

ANGLE

5/∞/2/3

ENTERCHOICE

3

7

About invalid operation icon

When you press a button, and if the unit does not accept its
operation, appears on your TV screen. Operations are
occasionally unacceptable even if is not displayed.

Note that some operations may not be accepted. For example,
some discs may not allow rapid advance/reverse or slow­motion playback.

Turning on/off the unit

Press STANDBY/ON on the remote control
unit or press STANDBY/ON on the front
panel.

The STANDBY indicator on the front panel, which lights in
red during standby, goes off.

The opening display appears on the TV screen, and the following
messages may appear at the bottom of the opening display.

Initial setup

When you turn on the unit for the first time after purchase, the
following message appears on the TV screen.

EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
YES - PRESS ENTER NO - CANCEL

You can set the display language, TV monitor type and digital
output before using the unit, by following the procedure below.

1 Press ENTER.

The first page of the DVD PLAYER SET UP display appears.
The pull-down menu of the [ON SCREEN LANGUAGE] is
already open.

DVD PLAYER SET UP

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

SELECT

ENGLISH

ENGLISH

OFF

ENGLISH

ENGLISH
SPANISH
FRENCH

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM

ON SCREEN LANGUAGE options

2 Press 5/∞ to select the desired language.

You can select the on-screen language for the preference
displays, etc. from among ENGLISH, SPANISH and
FRENCH.

3 Press ENTER.

The second page is shown, in which the pull-down menu of
the [MONITOR TYPE] is already open.

DVD PLAYER SET UP

MONITOR TYPE

PICTURE SOURCE

SCREEN SAVER

SELECT

4:3 L.B.

16:9 NORMAL

AUTO

16:9 AUTO
4:3 LB

ON

4:3 PS

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM

MONITOR TYPE options

NOW READING

Message area

• NOW READING (The unit is reading the disc information.)

• REGION CODE ERROR! (The region code of the DVD VIDEO
disc does not match the unit. The disc cannot be played back.)

•OPEN

•CLOSE

•NO DISC

NOTE

Even if you turn off the unit, the unit is not disconnected from the
AC power source as long as it is connected to the wall outlet. This
state is called standby mode. In this state, the unit consumes a
very small amount of power.

6

4 Press 5/∞ to select the desired monitor type.

For a normal (conventional) TV, select [4:3 LB] or [4:3 PS].
For a wide-screen TV, select [16:9 NORMAL] or [16:9 AUTO]
(see page 22) .

5 Press ENTER.

The third page is shown, in which the pull-down menu of the
[DIGITAL AUDIO OUTPUT] is already open.

DVD PLAYER SET UP

DIGITAL AUDIO OUTPUT

ANALOG DOWN MIX

D RANGE CONTROL

OUTPUT LEVEL

SELECT

DIGITAL AUDIO OUTPUT options

DOLBY DIGITAL/PCM

PCM ONLY

DOLBY PROLOGIC

DOLBY DIGITAL/PCM
STREAM/PCM

ON

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM

6 Press 5/∞ to select a desired digital output

signal type.

Set this item correctly when you connect the unit to an
external surround decoder or D/A converter. (If you do not
connect the unit to such a device, you do not have to set this
item.)

• When connecting to a Dolby Digital decoder, select
[DOLBY DIGITAL/PCM].

• When connecting to a DTS decoder, select [STREAM/
PCM].

• When connecting to other digital device, select [PCM
ONLY].

7 Press ENTER.

The TV screen returns to the opening display.

To bring up the DVD PLAYER SET UP display later

Press CHOICE for a few seconds until the DVD PLAYER SET UP
display appears.

Basic operations

Basic playback

1 Press 0 to open the disc tray.
2 Place a disc in the disc tray.

With the label side up

E

SIV
ES
R
G

RO
P

To change the brightness of the display window

Press and hold DISPLAY.
You can select the display window brightness from three levels.
Release DISPLAY at the desired brightness.

• To insert an 8-cm disc, place it in the inner recess.

3 Press 3.

The unit starts playback from the beginning.

If a menu is shown on the TV screen

When inserting a DVD VIDEO, SVCD or Video CD disc, a menu
may be shown on the TV screen. From the menu, you can select
a desired item to be played back.

For DVD VIDEO

1Press 5/∞/2/3 to select a desired item.
2Press ENTER.

The unit starts playback of the selected item.

For SVCD/Video CD

Press the numeric buttons to select a desired item.
The unit starts playback of the selected item.

NOTES

• Do not insert an unplayable disc. (See page 2.)

• When inserting a disc on the disc tray, be sure to position the
disc inside the recess. Otherwise, the disc may be damaged
when the disc tray is closed, or you may not be able to remove
the disc from the unit.

About PBC (Playback Control)

Some SVCD/Video CD discs support the PBC function.
The PBC function allows you to enjoy menu-driven operation
and high-resolution still images which have a resolution four
times greater than moving pictures.

• To play a PBC-compatible SVCD/Video CD disc without
activating the PBC function, press the numeric buttons
instead of 3 to start playback.

• To activate the PBC function again,

1) press TOP MENU or MENU,

or

2) press 7 to stop playback, then press 3.

Basic

operations

7

Basic operations

Basic

operati

ons

K

QUICK PLAYBAC

7380

To stop playback completely

Press 7.

Hint

If you press 0 during playback, the unit stops playback and
opens the disc tray.

4¢

DISPLAY

1/¡

4

7

ON SCREEN

3
¢

8

To check the playback status

You can see the current selection number (the title/chapter
number for DVD VIDEO or track number for SVCD/Video CD/
Audio CD), time information (the track or chapter time while
stopped, or elapsed track or chapter time during playback) and
the transport status (stop, playback, pause, etc.) on the TV
screen.

Press ON SCREEN.

Example: for DVD VIDEO

Transfer rate

8.5Mbps

Note that pressing ON SCREEN again brings up the menu bar
under the status bar, from which you can access various
functions. See page 17 for details about the menu bar.

To turn off the status bar

Press ON SCREEN repeatedly until the status bar goes off.

Current chapter

number

TITLE 33 TOTAL 1:25:58CHAP 33

Current title number

Current transport

status

Current chapter

time

To stop playback temporarily

Press 8.

To resume playback, press 3. (See the following item.)

About On-screen guide icons

You may see the following icons displayed over the picture.
They have the following meanings.

: Appears at the beginning of a scene recorded from

multiple angles (see page 15).

: Appears at the beginning of a scene recorded with

multiple audio languages (see page 15).

: Appears at the beginning of a scene recorded with

multiple subtitle languages (see page 15).

Resuming playback

The unit can memorize the position on a disc where you interrupt
playback, and resume playback from that position later.
There are three resume modes; ON, OFF and DISC RESUME.
The mode is initially set to ON when you purchased the unit.

• You can select the mode using the preference display (see
page 23).

When the resume mode is “ON”

When you press 7, the unit stops playback and memorizes the
interrupted position. The TV screen shows [RESUME STOP] and
the “RESUME” indicator lights up in the display window.
The memory of the interrupted position is not cleared if you turn
off the unit.
When you turn off the unit after setting the resume function,
simply press 3. The unit is turned on, and playback starts from

the interrupted position. If you turn on the unit by pressing
STANDBY/ON then press 3, playback starts from the beginning
of the disc.
Note that the memory is cleared if you open the disc tray.

To change the display window contents

Press DISPLAY.

Example: for DVD VIDEO
Each time you press DISPLAY, the total time display and the
title/chapter number display appear alternately.

Total time

8

Title number

Chapter number

When the resume mode is “DISC RESUME”

When you press 7, the unit stops playback and memorizes the
interrupted position. The TV screen shows [RESUME STOP] and
the “RESUME” indicator lights up in the display window.

The memory of the interrupted position is not cleared if you open
the disc tray or turn off the unit.

Hint

The unit memorizes interrupted positions for the last 30 discs
played. Storing a new interrupted position will erase the
interrupted position stored for the first disc.

To clear the memory

Press 7 while the disc is stopped.

Basic operations

To resume playback

When the resume mode is “ON”

While the disc you interrupted playback is
still on the disc tray, press 3.

The unit resumes playback from the position where playback
was interrupted. The TV screen shows “RESUME PLAY.”

To play back from the beginning

Press 7 before pressing 3 to start playback.

When the resume mode is “DISC RESUME”

1 Press 0 to insert a disc for which the unit has

stored an interrupted position.

The TV screen shows [RESUME STOP].

2 Press 3.

The TV screen shows [RESUME PLAY] and the unit resumes
playback from the position where playback was interrupted.

To play back from the beginning

After inserting the disc, press 7 before pressing 3 to start
playback.

NOTES

• If you change the [RESUME] setting from [DISC RESUME] to
[OFF] or [ON], you cannot resume playback of a disc whose
“resuming” position is stored. However, when you again set
[RESUME] to [DISC RESUME], you will then be able to resume
playback of the disc.

• If you interrupt the playback of a disc for which an interrupted
position has already been stored, the memory will be updated
with the new interrupted position.

• For a double-sided DVD VIDEO disc, the unit regards each side
as a different disc. Therefore, to resume playback of such a
disc, the disc must be inserted with the same side down.

• When the unit memorizes an interrupted point for a disc, it also
memorizes Audio, Subtitle and Angle settings.

• The unit may not resume playback exactly from the intterupted
point. In the case of an SVCD/Video CD disc with PBC function,
the unit may resume playback from a point slightly earlier or
later than the point where playback was interrupted.

NOTES

• x1.5 Quick Playback can also be achieved by pressing ¡

once. (See next section.)

• At the x1.5 Quick Playback mode, the digital sound is output in
stereo linear PCM format. Note that the sound of a DTS­encoded DVD VIDEO disc is not output.

• Depending on a disc, the sound may not be in tune, or the
sound quality may alter during the x1.5 Quick Playback mode.

To advance or reverse playback rapidly
while monitoring

During playback, press ¡ or 1 on the
remote control unit.

You can select from 1.5 times, 5 times, 20 times and 60 times
normal speed. Pressing 3 returns the unit to normal
playback.

During playback, hold down ¢ or 4.

Playback is advanced or reversed at 5 times normal speed.

NOTE

During rapid playback, the sound will be muted except when
playing an Audio CD, and when playing a DVD VIDEO or Video
CD at 1.5 times normal speed.

To advance a still picture frame by frame

While paused, press 8.

Each time you press 8, the still picture advances to the next
frame.
Pressing 3 returns to normal playback.

To play back in slow motion

Basic

operations

Various speed playback

x1.5 Quick Playback with sound

During playback, press QUICK PLAYBACK on
the unit.

The lamp on the QUICK PLAYBACK button turns on, and the
disc is played back at about 1.5 times normal speed.
The sound is not muted, and the subtitle does not go off.

To return to the normal playback

Press QUICK PLAYBACK again.
The lamp on the button goes off.

You can select from 1/32 times, 1/16 times, 1/4 times and 1/2
times normal speed.

During playback, press 8, then press ¡ (to
play forward slow motion), or 1 (to play
reverse slow motion, for DVD VIDEO disc
only).

Pressing 3 returns to normal playback.

NOTES

• During slow motion playback, the sound will be muted.

• Reverse slow motion playback is not possible for an SVCD and
Video CD.

9

Basic operations

Basic

operati

ons

4¢

Numeric buttons

Locating the beginning of a scene or
song

For DVD VIDEO: During playback, you can skip a chapter or title,

depending on the disc configuration.

For SVCD/Video CD: During playback without PBC function, you

can skip a track.

For Audio CD: During playback or while in stop mode, you can

skip a track.

To skip forward, press ¢.

To skip backward, press 4.

4

¢

To replay the previous scenes (One touch
replay function)

During DVD VIDEO playback, press .

The playback position moves back 10 seconds before the
current position.

NOTES

• This function works only within the same title, though it works
between chapters.

• This function may not work with some DVD VIDEO discs.

Using the numeric buttons

For DVD VIDEO/Audio CD: During playback or while in stop

mode

For SVCD/Video CD: During playback without PBC function or

while in stop mode

Press the numeric buttons to specify the
number.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

The unit starts playback from the beginning of the selection.

NOTES

• Depending on the disc type and the unit status, what is
specified differs:

Unit status Disc type What is specified

While stopped DVD VIDEO title

SVCD/Video CD/Audio CD track

During playback DVD VIDEO chapter

SVCD/Video CD/Audio CD track

• During DVD VIDEO playback, if a menu is shown on the TV
screen, the numeric buttons may be used for selecting an item
in the menu.

About screen saver function

A television monitor may have an image burned into it if a static
image is displayed for a long time. To prevent this, the unit
automatically activates the screen saver function if a static
picture, such as an on-screen display or menu, is displayed for
over 5 minutes.
When the screen saver function is activated, the TV screen
gets darker.
Pressing any buttons will release the screen saver function.

10

Advanced operations

RETURNTITLE/GROUP

Locating a desired scene from the menu of
a SVCD/Video CD with PBC

Numeric buttons

TOP MENU

5/∞/2/3

4

MENU

ENTER

3
¢

Playing from a specific position

Locating a desired scene from the DVD
menu

DVD VIDEO discs generally have their own menus which show
the disc contents. These menus contain various items such as
titles of movies, names of songs, or artist information, and display
them on the TV screen. You can locate a desired scene using the
DVD menu.

1 While a DVD VIDEO disc is inserted, press

TOP MENU or MENU.

The menu appears on the TV screen.

2 Press 5/∞/2/3 to select a desired item, then

press ENTER.

The unit starts playback of the selected item.

Hints

• Some DVD VIDEO discs may also have a different menu which
appears when MENU is pressed.

• See the instructions of each DVD VIDEO disc for its particular
menu.

• With some discs, you can select items by entering the
corresponding number using the numeric buttons, which may
cause the unit to automatically start playback.

Some SVCD/Video CD discs support the PBC function. PBC is
an abbreviation of “Playback Control.” Some SVCD/Video CD
discs recorded with PBC have their own menus, such as a list of
the songs of the disc. You can locate a specific scene by using
the PBC menu.

1 In stop mode, press 3 or TOP MENU.

A disc menu appears on the TV screen.

2 Press the numeric buttons to select the

desired item.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

The unit starts playback of the selected item.
To return to the menu, press RETURN.

Hint

If something like [NEXT] or [PREVIOUS] appears on the TV
screen, pressing ¢ advances to the next page, and pressing
4 returns to the previous page.

Specifying a desired title

1 During playback, press TITLE/GROUP.

[--] is shown in the title display area of the display window.

2 Press the numeric buttons to specify a title to

be played.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

The unit starts playback from the specified title.

NOTE

This function may not work with some DVD VIDEO discs.

Advanced

operations

NOTE

The MENU button does not work while stopped.

11

Advanced operations

Advanced

ope

rations

CANCEL

Numeric
buttons

5/∞/2/3

ENTER

3

ON SCREEN

7

Locating a desired position in the current
title or track (Time search)

You can play a disc from the desired position by specifying the
time from the beginning of the current title (for DVD VIDEO) or
the disc (for SVCD/Video CD/Audio CD).

For DVD VIDEO/Audio CD: During playback or while in stop

mode

For SVCD/Video CD: In any condition except SVCD/Video CD

playback with PBC

1 Press ON SCREEN twice.

The menu bar appears on the TV screen.

2 Press 2/3 to move to , then press

ENTER.

The pull-down menu for entering time appears.

Screen example for DVD VIDEO

CHAP.

TITLE 33 TOTAL 1:25:58CHAP 33

1/3 1/3OFF 1/5

TIME 25:58TRACK 33

8.5Mbps

TIME _:__:__

Screen example for Audio CD

OFF PROG. RND.

TIME __:__

3 Press the numeric buttons (0 to 9) to enter

the desired time.

The specified time is displayed in the pull-down menu.

Example (for DVD VIDEO)

To play back from 2(H):34(M):00(S)
Press 2, 3, then 4.

TIME 2:34 __:

Example (for SVCD/Video CD/Audio CD)

To play back from 23(M):40(S)
Press 2, 3, then 4.

TIME 23 4_:

You do not have to press “0” to enter the trailing zeros (for the
last two digits in the example above).

To correct a mistake

Press 2 repeatedly to move back to the digit where you
entered a wrong number, and reenter the correct one.

4 Press ENTER.

The unit starts playback from the specified time.

To dismiss the menu bar

Press ON SCREEN.

Hint

“10” and “+10” buttons are not used with this function.

NOTES

• Some DVD VIDEO discs do not contain time information, and
the time search function cannot be used.

• The time search function cannot be used during program
playback.

Changing the playback order

To play back in a specific order (Program
play)

By programming tracks, you can play up to 99 tracks in any order.
You may program the same track more than once.

1 In stop mode, press ON SCREEN twice.

The menu bar appears on the TV screen.

2 Press 2/3 to move to .

Screen example for Audio CD

OFF PROG. RND.

PROG.

TIME 25:58TRACK 33

3 Press ENTER.

The program table appears.
The PROG indicator lights up in the display window.

12

Advanced operations

4 Press the numeric buttons to specify tracks

in the desired order.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

The total program time

PROGRAM

No. TrackDisc
1 2 1
2 3 5
3 7 4
4 4 2
5 3 3
6 5 4
7 6 6
8
9
10

USE NUMERIC KEYS TO PROGRAM TRACKS.
CANCEL DELETES THE LAST STEP.

To correct the program

Press 5/∞ to move
press CANCEL. The track is erased and the subsequent
programmed tracks move up.
Pressing 7 clears all the programmed tracks.

to the track to be corrected, then

Total Program Time 00:25:12

7 DELETES ALL.

Selected track number

5 Press 3 to start program playback.

With an Audio CD disc, the program table remains on the TV
screen during program playback. (Pressing ON SCREEN
brings up the status bar.)
When all of the programmed tracks have finished playback,
the unit stops and the program table appears again.
Note that the program remains.

• During program playback, you cannot edit the program
contents.

To play back in random order (Random play)

1 In stop mode, press ON SCREEN twice.

The menu bar appears on the TV screen.

2 Press 2/3 to move to .

Screen example for Audio CD

OFF PROG. RND.

RND.

TIME 25:58TRACK 33

3 Press ENTER.

The unit starts random playback.
With an SVCD/Video CD disc, the menu bar is automatically
dismissed.
During random playback, the RND indicator lights up in the
display window.
After playing all tracks of the disc, the unit stops the disc and
exits the random playback mode.

To stop and quit random playback

Press 7. The unit stops playback and exits the random playback
mode.

Advanced

operations

To check the program contents

During playback, press 7. Playback stops and the program table
is shown.
When the unit is playing back an Audio CD and the program table
is not shown, you can bring up the table by carrying out steps 1 to

3.
During SVCD/Video CD playback, you can check the program
contents via the menu bar.

To stop program playback

Press 7.

To clear the program

While stopped and the program table is shown, press 7.

To exit the program mode

After clearing the program, press ON SCREEN.

NOTE

When the disc tray is opened or the unit is turned off, the program
is cleared.

13

Advanced operations

Advanced

ope

rations

To repeat a desired part (A-B repeat
playback)

SUB TITLE

ANGLE

5/∞/2/3

AUDIO

ENTER

ON SCREEN

Repeat playback

To repeat the current selection or all tracks

For DVD VIDEO: During playback
For SVCD/Video CD/Audio CD: In any condition except SVCD/

Video CD playback with PBC

1 Press ON SCREEN twice.

The menu bar appears on the TV screen.

2 Press 2/3 to move to , then press

ENTER.

The pull-down menu for repeat mode selection appears.

3 Press 5/∞ to select the desired repeat mode.

For DVD VIDEO

CHAPTER: current chapter repeat
TITLE: current title repeat
A-B: see “To repeat a desired part (A-B repeat playback)” on

this page.

For SVCD/Video CD/Audio CD

TRACK: current track repeat
ALL: all track repeat
A-B: see “To repeat a desired part (A-B repeat playback)” on

this page.

First make sure:

• The unit is in playback mode except SVCD/Video CD playback
with PBC.

1 Press ON SCREEN twice.

The menu bar appears on the TV screen.

2 Press 2/3 to move to , then press

ENTER.

The pull-down menu for repeat mode selection appears.

3 Press 5/∞ to select [A-B].
4 Press ENTER at the beginning of the part you

want to repeat (point A).

The pull down menu disappears.

The repeat icon shows .

A-

5 Press ENTER at the end of the part you want

to repeat (point B).

The repeat icon shows .
The unit locates “A” and starts repeat playback between “A”
and “B.”
The “ ” indicator lights in the display window.

To quit A-B repeat playback

Press 2/3 to move to , and press ENTER. The A­B repeat mode turns off, then normal playback continues.

NOTE

The A and B points must be set in the same title/track.

A-B

A-B

If you select the repeat mode while stopped, press 3 to start
repeat playback.
The “ ” indicator lights in the display window.

To quit repeat playback

Select [OFF] at step 3 above.

Hint

When the program playback mode is active with an SVCD, Video
CD or Audio CD, the repeat mode changes in the same manner.

Note, however, that in the “ ” mode the unit repeats all the
programmed tracks instead of all tracks on the disc.

NOTE

The repeat playback may not work with some discs, even if you
select one of the repeat modes.

14

Changing the language, sound and
scene angle

To select the subtitle language (SUBTITLE)

Some DVD VIDEO and SVCD discs contain more than one
subtitle language. You can choose a desired one from them.

Hint

At the beginning of the part where the subtitles are recorded,
appears on the TV screen (except when the [ON SCREEN
GUIDE] preference is set to [OFF]).

1 During playback, press SUBTITLE.

The subtitle selection window appears on the TV screen.

1/3

ENGLISH

2 Press 5/∞ or SUBTITLE to select the subtitle.

Each time you press 5/∞ or SUBTITLE, the subtitle
language changes.

3 Press ENTER.

Subtitles are displayed in the selected language.
The subtitle selection window is dismissed.

NOTES

• An SVCD disc can have up to four subtitles. Pressing 5/∞

cycles through those channels regardless of whether the
subtitles are recorded or not.

• The Subtitle selection window will automatically disappear if
you do not change the subtitle for several seconds.

• For DVD VIDEO, the selected language may be abbreviated on
the TV screen. See “Appendix B: Table of languages and their
abbreviations” on page 30.

To change the audio language or sound
(AUDIO)

Advanced operations

2 Press 5/∞ or AUDIO to select the desired

audio.

Each time you press 5/∞ or AUDIO, the audio changes.

For DVD VIDEO (example)

1/3 ENGLISH 2/3 FRENCH 3/3 SPANISH

For SVCD

ST1 ST2 L- 1 R-1 L- 2 R-2

For Video CD

ST (Stereo) L R

3 Press ENTER.

You can hear the selected audio.
The audio selection window is dismissed.

NOTES

• The audio selection window will automatically disappear if you
do not change the audio for several seconds.

• For DVD VIDEO, the selected language may be abbreviated on
the TV screen. See “Appendix B: Table of languages and their
abbreviations” on page 30.

To select a scene angle of DVD VIDEO
(ANGLE)

You can enjoy a variety of scene angles if the DVD VIDEO disc
contains “multi-angle” parts, where multiple cameras were used
to shoot the same scene from different angles.

Hint

At the beginning of a “multi-angle” part, appears on the TV
screen (except when the [ON SCREEN GUIDE] preference is set
to [OFF]).

1 During playback, press ANGLE.

The angle selection window appears on the TV screen.

1/3

1

Advanced

operations

The audio selection setting allows you to change the audio
language of a movie, or to listen to karaoke with or without the
vocal.

Hint

At the beginning of the part where multiple audio tracks are
recorded, appears on the TV screen (except when the [ON
SCREEN GUIDE] preference is set to [OFF]).

1 During playback, press AUDIO.

The audio selection window appears on the TV screen.

1/3

ENGLISH

2 Press 5/∞ or ANGLE to select the desired

angle.

Each time you press 5/∞ or ANGLE, the angle changes.

3 Press ENTER.

You can see the picture from the selected angle.
The angle selection window is dismissed.

NOTE

The angle selection window will automatically disappear if you do
not change the angle for several seconds.

15

Advanced operations

Advanced

ope

rations

3D PHONIC

ZOOM

5/∞/2/3

ENTER

VFP

ON SCREEN

Special picture/sound effect

To zoom in pictures

1 During playback or while paused, press

ZOOM.

Pressing ZOOM causes the unit to zoom in on the image.
At the top left of the screen, the information for the current
magnification appears for about 5 seconds.
Each time you press ZOOM, the magnification is doubled (up
to 64 times).

ZOOM x 4

When a picture of a DVD VIDEO disc is viewed on a normal
TV screen (4:3, Letter Box), black bars may appear at the top
and bottom of the screen. In this case, if you select the
“ZOOM × 1.8” mode, the black bars become almost invisible.
When a 1:2.35 or 1:1.85 DVD VIDEO source is played back,
however, the black bars are visible on the screen.

2 Press 5/∞/2/3 to move the zoomed position.

To return to the normal playback

Press ENTER.

NOTE

While zoomed, the picture may look coarse.

2 Press 2/3 to select the desired preset.

Each time you press the button, the VFP mode changes as
follows.
Set the video type most suitable to the current program or the
room conditions.

NORMAL CINEMA USER 1 USER 2

Selected preset

USER 1

GAMMA

BRIGHTNESS

CONTRAST

SATURATION

TINT

SHARPNESS

Y DELAY

Parameter

[NORMAL]: for watching TV in a general room.
[CINEMA]: for watching a movie software in a room with

suppressed light.

[USER 1] [USER 2]: you can adjust parameters that affect

the picture character and store the settings as a user
preset. See the next step.

+ 4

+ 4

+13

+13

+13

+ 3

+ 2

3 To define a user setting, press 5/∞ to select a

parameter to be edited from the following.

•GAMMA

Adjust this if the neutral color is bright or dark. The
brightness of dark and bright portion is maintained.
Available range: –4 (darkest) to +4 (brightest)

• BRIGHTNESS

Adjust this if the picture is bright or dark on the whole.
Available range: –16 (darkest) to +16 (brightest)

• CONTRAST

Adjust this if the far and near position is unnatural.
Available range: –16 to +16

• SATURATION

Adjust this if the picture is whitish or blackish.
Available range: –16 (blackest) to +16 (whitest)

•TINT

Adjust this if the appearance of flesh tone is unnatural.
Available range: –16 to +16

• SHARPNESS

Adjust this if the picture is indistinct.
Available range: 0 to +3

•Y DELAY

Adjust this if the picture looks separately/overlapped.
Available range: –2 to +2

4 Press ENTER.

A window for setting parameters appears.

To adjust the picture character (VFP)

The VFP (Video Fine Processor) function allows you to adjust the
picture character according to the type of programming, picture
tone or personal preferences.

1 During playback, press VFP.

The VFP mode selection window appears on the TV screen.

16

SATURATION + 4

Selected parameter

5 Press 5/∞ to adjust the level of the

parameter.

The higher value enhances the effect.

6 Press ENTER.

Repeat steps 3 to 6 if you want to set other parameters.

To dismiss the VFP mode selection window

Press VFP.

NOTES

• The window for VFP mode selection and parameter setting
disappear if no operation is made for about 10 seconds.

• While zoomed, the VFP function cannot be used.

To simulate surround sound (3D PHONIC)

Using the 3D PHONIC function, you can get a simulated
surround effect from your stereo system.

1 During playback, press 3D PHONIC.

The 3D PHONIC window appears on the TV screen.

2 Press 2/3 to select the desired mode.

Each time you press the button, the 3D PHONIC mode
changes as follows:

ACTION DRAMA THEATER NONE

+ 5ACTION 4

Advanced operations

Menu bar functions

To bring up the menu bar

1 When a disc is inserted, press ON SCREEN.

A status bar for the type of disc inserted will appear on the TV
screen.
See page 8 for details about the status bar.

2 Press ON SCREEN again.

A menu bar for the type of disc inserted will appear under the
status bar.

(for DVD VIDEO)

8.5Mbps

(for SVCD)

OFF

(for Video CD)

OFF

TITLE 33 TOTAL 1:25:58CHAP 33

CHAP.

PROG. RND.

1/3 1/3OFF 1/5

ST1

STPROG. RND.

TIME 25:58TRACK 33

-/4

TIME 25:58TRACK 33

Selected effect mode

•ACTION

Suitable for action movies and sports programs in which the
sound source moves.

• DRAMA

Natural and warm sound. You can enjoy movies in a relaxed
mood.

•THEATER

You can enjoy sound effects like in a theater.

3 Press 5/∞ to adjust the effect level.

You can set the effect level from [1] to [5].
The higher value enhances the effect.

To dismiss the 3D PHONIC window

Press 3D PHONIC.

NOTES

• The 3D PHONIC window disappears if no operation is made for
about 10 seconds.

• The 3D PHONIC function works correctly only when playing
back a DVD VIDEO disc recorded with Dolby Digital.

• When playing back a DVD VIDEO disc recorded with Dolby
Digital that does not contain the rear signal, you can change the
3D PHONIC setting, but you will not be able to achieve a correct
3D effect.

• The 3D PHONIC function does not affect the Dolby Digital
bitstream signal from the DIGITAL OUT jack.

• When the 3D PHONIC function is active, the [ANALOG DOWN
MIX] setting in the [AUDIO] setting display is not available.

(for Audio CD)

TIME 25:58TRACK 33

OFF PROG. RND.

To dismiss the menu bar and status bar

Press ON SCREEN.

Basic operation procedure

1 Press 2/3 to select the icon you want to

work with.

The selected icon is pointed by .

2 Press ENTER.

With many icons, an appropriate pull-down window appears,
however, there are some exceptions.

NOTES

• A mark or text on the menu icon for the function or mode
currently selected is shown in green.

• Some functions are not available during playback. (You cannot
move to the associated icon when it is not available.)

Advanced

operations

17

Advanced operations

Advanced

ope

rations

Menu bar functions for DVD VIDEO

Time mode selection

During playback, selects the time mode shown in the display
window and in the status bar.

Press ENTER to select the time mode from the following.

• TOTAL: Current title elapsed time

• T.REM: Current title remaining time

• TIME: Current chapter elapsed time

• REM: Current chapter remaining time

Repeat mode (See also page 14)

Selects the repeat mode during playback.

1. Open the pull-down window.

2. Press 5/∞ to select the repeat mode from the following.

• CHAPTER: Current chapter repeat

• TITLE: Current title repeat

• A-B: A-B repeat

• OFF: Repeat mode deactivated

3. Press ENTER to make the selected repeat function active.

Time search (See also page 12)

Specifies a time from the beginning of the current title as the
point from which to begin playback.

CHAP.

During playback, specifies a desired chapter to be played back
from.

1. Open the pull-down window.

2. Press numeric buttons (0 to 9) to enter a desired chapter
number. (For example, to specify “10,” press 1, then 0.)

3. Press ENTER to begin playback from the specified chapter.

Chapter search

Menu bar functions for SVCD/Video CD/
Audio CD

Time mode selection

Selects the time mode shown in the display window and in the
status bar.

Press ENTER to select the time mode from the following.

• TIME: Current track elapsed time

• REM: Current track remaining time (while in stop mode,

• TOTAL:Disc elapsed time

• T.REM:Disc remaining time (while in stop mode, disc total time)

Selects the repeat mode.

1. Open the pull-down window.

2. Press 5/∞ to select the repeat mode from the following.

3. Press ENTER to make the selected repeat function active.

Specifies a time from the beginning of the disc as the point from
which to begin playback.

PROG.

While stopped, specifies the playback order of tracks.

While stopped, activates random playback.

current track total time)

Repeat mode (See also page 14)

• TRACK:Current track repeat

• ALL: All track repeat

• A-B: A-B repeat

• OFF: Repeat mode deactivated

Time search (See also page 12)

Program playback (See also pages 12 and 13)

RND.

Random playback (See also page 13)

Audio selection (See also page 15)

During playback, selects the audio language or sound track.

1. Open the pull-down window.

2. Press 5/∞ to select a desired audio language or sound track.

3. Press ENTER to begin playback with the selected audio.

Subtitle selection (See also page 15)

During playback, selects the subtitle language.

1. Open the pull-down window.

2. Press 5/∞ to select a desired subtitle language.

3. Press ENTER to begin playback with the selected subtitle.

Angle selection (See also page 15)

During playback, selects a desired scene angle in a multi-angle
part.

1. Open the pull-down window.

2. Press 5/∞ to select a scene angle.

3. Press ENTER to begin playback with the selected scene angle.

Audio selection (See also page 15)

During SVCD/Video CD playback, selects the audio channel(s).

1. Open the pull-down window.

2. Press 5/∞ to select a desired audio channel(s).

3. Press ENTER to play back with the selected audio channel(s).

Subtitle selection (See also page 15)

During SVCD playback, selects the subtitle.

1. Open the pull-down window.

2. Press 5/∞ to select a desired subtitle.

3. Press ENTER to begin playback with the selected subtitle.

18

MP3 disc playback

Basic operations

Use the following buttons to control MP3 disc playback.

ENTER: Starts playback while stopped.

3: Starts playback while stopped or paused.
7: Stops playback.
8: Pauses playback.
4/¢: Skips back or forward a track during playback.

Selects the previous or next track while stopped.

5/∞/2

4

7

3
¢

8

Operations

The unit can play back MP3 files on a personally recorded CD-R/
RW disc or commercially available CD. We refer to a disc that
contains MP3 files as an “MP3 disc” in this manual.

About MP3 discs

On an MP3 disc, each song is recorded as a file (track). Files are
sometimes grouped into folders by artists, album, etc.

• Each file is regarded as a track.

• A folder which has one or more files is regarded as a group.

• A folder which does not directly contain any tracks is ignored.

• Files which do not belong to any folder are grouped into “group

1.”

• The unit recognizes up to 150 tracks per group, and up to 99

groups per disc. If there are files other than MP3 files, they also
count in the 150-file total.

Max. 99 groups per disc

Track 1.mp3
Track 2.mp3
Track 3.mp3

Group 2

Group 4

Group 1

Track 4.mp3
Track 5.mp3
Track 6.mp3

If you press 3 during playback, or press 7 to stop playback
followed by 3, the unit starts playback from the beginning of the
current track.

NOTES

• The unit does not support “packet writing” discs.

• The unit does not support the ID3 tag.

• The unit supports discs recorded with multiple sessions.

• Some discs may not play due to disc characteristics or
recording conditions.

• Programmed and random playback functions do not work with
MP3 discs.

• The unit only can play back tracks with the following file
extensions; “.MP3,” “.Mp3,” “.mp3” and “.mP3.”

• Time required for reading the disc contents may vary for
different discs, depending on the numbers of groups (folders)
and tracks (files) recorded, etc.

• You cannot advance or reverse playback by pressing ¡ or
1, or by holding down ¢ or 4 during MP3 disc playback.

Selecting the desired group and track

When inserting an MP3 disc, after the disc contents are read, the
MP3 CONTROL display automatically appears on the TV screen.
You can specify the desired group/track from the display using
the following procedure.

1 Make sure that the black (cursor) bar is in the

left (group) column.

If it is in the right column, press 2 to move it to the left
column.

2 Press 5/∞ to move the bar to a desired

group.

On the right column, tracks in the selected group are shown.

3 Press 4/¢ to select a desired track, then

press ENTER or 3.

or

Press the numeric buttons to directly specify
a desired track number.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

The unit starts playback from the selected track.

playback

MP3 disc

Max.150 tracks
per group

Group 3

Notes for making your own MP3 disc using a CD-R/
CD-RW disc

• Select “ISO 9660” as the disc format.

• We recommend you record your material at a 44.1 kHz
sampling rate, using the 128 kbps data transfer rate.

19

MP3 disc playback

MP3 disc

playback

p

TITLE/GROUP

4

7

Numeric buttons

5/∞/3

3
¢

2 Press the numeric buttons to specify a

desired group number.

To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.

Specify the Group number within several seconds after
pressing TITLE/GROUP (i.e. while the display window shows
[--]).
The unit starts playback from track 1 of the selected group.

3 Press the numeric buttons to specify a

desired track number.

The unit starts playback from the specified track.
You can also use 4/¢ or 5/∞ to specify a track, instead
of the numeric buttons.

Repeat playback

1 During playback or while stopped, press ON

SCREEN.

The repeat mode selection window appears on the TV
screen.

Current track elapsed time

MP3/WMA CONTROL
Group : 01 / 10
spring

summer
fall
winter
sea
mountain
camp
picnic
skiing
flower

Group column

Time : 00:03:08
Track : 01 / 06 (Total 28)
begonia.mp3

german chamomile.mp3
kiwi fruit.mp3
orchard grass.mp3
petunia.mp3
north pole.mp3

Track column of the

Selected track

current group

Hint

You can also select a desired track by pressing 3 to move the
black bar to the right (track) column then using 5/∞.

NOTES

• If an MP3 file name includes any 2-byte character, the unit
cannot show the file name correctly.

• Only MP3 files are shown on the MP3 CONTROL display.

• The order of groups/tracks shown in the MP3 CONTROL
display may differ from the order shown on your personal
computer when you set the disc on your computer.

OFF

2 Press 5/∞ to select the desired repeat mode.

TRACK: repeats the current track
GROUP:repeats all tracks in the current group
ALL: repeats all tracks on the disc

3 Press ENTER.

(TV screen)

Selected repeat mode

MP3/WMA CONTROL REPEAT TRACK
Group : 01 / 10

spring

summer
fall

If you select the repeat mode while stopped, you need to
press ENTER or 3 to start playback.

To stop repeat playback

Press 7. Note that the repeat mode remains active.

To quit repeat playback

Select [OFF] in step 2 above.

Track : 01 / 06 (Total 28)

begonia.mp3

german chamomile.mp3
kiwi fruit.m

3

Direct selection

You can select a desired group directly by specifying the group
number.

1 During playback or while stopped, press

TITLE/GROUP.

[--] is shown in the group display area of the display window.

20

Changing the initial settings

How to set preferences

1 Press CHOICE.

One of the preference on-screen displays appears on the TV
screen.
You can see four icons at the top right of the on-screen
display for the settings.

5/∞/2/3

: LANGUAGE menu

ENTERCHOICE

Selecting preferences

This section refers to the settings which are already made when
you purchase the unit. Read this section when you want to
connect this unit to a wide-vision TV set, or when you want to
otherwise change the settings according to your preferences and
viewing environment.

About the Preference display

The Preference display consists of the LANGUAGE, PICTURE,
AUDIO and OTHERS setting displays, each having setting items.

LANGUAGE

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

ENGLISH

ENGLISH

OFF

ENGLISH

: PICTURE menu

: AUDIO menu

: OTHERS menu

2 Press 2/3 to select the appropriate icon.

The appropriate display appears on the TV screen.

3 Press 5/∞ to move to select the item you

want to edit.

The color of the selected item changes.

4 Press ENTER.

A pull-down menu appears over the selected item.

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

SELECT

ENGLISH

ENGLISH

OFF

ENGLISH

ENGLISH
SPANISH
FRENCH

USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

Selected item

PICTURE

AUDIO

OTHERS

SELECT

PICTURE

MONITOR TYPE

PICTURE SOURCE

SCREEN SAVER

SELECT

AUDIO

DIGITAL AUDIO OUTPUT

ANALOG DOWN MIX

D RANGE CONTROL

OUTPUT LEVEL

SELECT

OTHERS

RESUME

ON SCREEN GUIDE

AUTO STANDBY

PARENTAL LOCK

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

4:3 LB

AUTO

ON

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

STREAM/PCM

STEREO

NORMAL

STANDARD

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

ON

ON

OFF

5 Press 5/∞ to select from the options then

press ENTER.

The selected option is set.

• For details about each setting, see the following.

To dismiss a preference display

Press CHOICE.

NOTES

• While an MP3 disc is inserted, you cannot bring up any
preference display.

• When a preference display is shown on a wide TV screen, the
upper and lower parts of the preference display sometimes may
be cut off. If this happens, adjust the picture size control of the
TV.

Changing the

initial settings

SELECT

USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

21

Changing the initial settings

Changing t

he

initial settings

LANGUAGE menu

MENU LANGUAGE

You can select the default menu language to be displayed if it is
contained on a DVD VIDEO disc.

Setting options

ENGLISH, SPANISH, FRENCH, CHINESE, GERMAN, ITALIAN,
JAPANESE, language code from AA to ZU

• If the disc does not have a menu in the selected language, the
disc’s default language will be used.

• For details about language codes, see “Appendix B: Table of
languages and their abbreviations” on page 30.

• You cannot change the setting during playback.

AUDIO LANGUAGE

You can select the default audio language to be played if it is
contained on a DVD VIDEO disc.

Setting options

ENGLISH, SPANISH, FRENCH, CHINESE, GERMAN, ITALIAN,
JAPANESE, language code from AA to ZU

• If the disc does not have the selected language, the disc’s
default language will be used.

• For details about language codes, see “Appendix B: Table of
languages and their abbreviations” on page 30.

• You cannot change the setting during playback.

SUBTITLE

You can select the default subtitle language to be displayed if it is
contained on a DVD VIDEO disc.

Setting options

OFF, ENGLISH, SPANISH, FRENCH, CHINESE, GERMAN,
ITALIAN, JAPANESE, language code from AA to ZU

• If the disc does not have a subtitle in the selected language, the
disc’s default language will be used.

• For details about language codes, see “Appendix B: Table of
languages and their abbreviations” on page 30.

• You cannot change the setting during playback.

[16:9 AUTO] (Wide television screen): select when you

connect the unit to a wide-screen (16:9) TV.

[4:3 LB] (Letter Box conversion): select when you connect the

unit to a normal (4:3) TV.
When playing back a DVD VIDEO disc recorded in wide
picture format, the picture is shown with black bars at the top
and bottom.

[4:3 PS] (Pan Scan conversion): select when you connect the

unit to a normal (4:3) TV.
When playing back a DVD VIDEO disc recorded in wide
picture format, the picture is zoomed to fill the screen
vertically, and the left and right sides of the image are
chopped off.
Note, however, that the picture will be shown in the 4:3 LB
mode even if you select the 4:3 PS mode depending on the
disc.

ON SCREEN LANGUAGE

You can select the on-screen display language of the unit.

Setting options

ENGLISH, SPANISH, FRENCH

• Some on-screen messages are shown in English regardless of
the setting.

• You cannot change the on-screen language shown on the MP3
display.

PICTURE menu

MONITOR TYPE

You can select the monitor type to match your TV when you play
back DVD VIDEO discs recorded for wide-screen televisions.

Setting options

16:9 NORMAL, 16:9 AUTO, 4:3 LB, 4:3 PS
[16:9 NORMAL] (Wide television screen): select when you

connect the unit to a wide-screen (16:9) TV whose aspect
ratio is fixed to 16:9 (the unit automatically adjusts the screen
width of the output signal correctly when playing back a 4:3
source).
If you play a 4:3 DVD VIDEO source using the [16:9
NORMAL] mode, the picture character changes slightly due
to the process for converting the picture width.

PICTURE SOURCE

This mode selects whether the content on the disc is processed
by field (video source) or by frame (film source). You can obtain
optimal picture quality according to the source type to be played
back by selecting an appropriate option.

Setting options

AUTO, FILM, VIDEO(NORMAL), VIDEO(ACTIVE)
[AUTO]: select when playing back a disc containing both video

and film source materials.
The unit recognizes the picture type (film or video source) of
the current disc according to the disc information. Normally,
select this option.

[FILM]: select when playing back a film source disc.
[VIDEO(NORMAL)]: select when playing back a video source

disc with relatively a few movements.

[VIDEO(ACTIVE)]: select when playing back a video source disc

with relatively a lot of movements.

SCREEN SAVER

You can set the screen saver function to ON or OFF. (See page

10.)

Setting options

ON, OFF

22

Changing the initial settings

AUDIO menu

DIGITAL AUDIO OUTPUT

To connect the unit’s digital output to an external device equipped
with a digital input, this item must be set correctly.
See “Appendix C: Digital output signal chart” on page 30 for
details about the relation between the setting and output signals.

Setting options

PCM ONLY, DOLBY DIGITAL/PCM, STREAM/PCM
[PCM ONLY]: select when you connect the DIGITAL OUT jack of

the unit to the linear PCM digital input of other audio
equipment.

[DOLBY DIGITAL/PCM]: select when you connect the digital

input of a Dolby Digital decoder or an amplifier with a built-in
Dolby Digital decoder.
When this option is selected, playing back a disc recorded by
the MPEG Multichannel format outputs a linear PCM digital
signal.

[STREAM/PCM]: select when you connect the digital input of an

amplifier with a built-in DTS, MPEG Multichannel or Dolby
Digital decoder, or the stand-alone unit of such a decoder.

• With some DVD VIDEO discs that are not fully copy-protected,
a 20 or 24 bit digital signal may be output.

• A signal recorded with the 96 kHz or higher sampling frequency
is output from the DIGITAL OUT jack with the 48 kHz sampling
frequency.

• The unit does not provide the DTS decoding function.

• When playing a DVD VIDEO or Audio CD disc with DTS, use a
DTS decoder to get correct signals from your speakers.

• DTS-encoded signal is output only from the unit’s DIGITAL OUT
jacks.

• If the unit is not connected to audio equipment with a DTS
decoder, DTS-encoded signal output from the DIGITAL OUT
jacks is distorted.

ANALOG DOWN MIX

To correctly play the audio on a DVD VIDEO disc recorded with
surround multichannel audio, you must set this item properly
according to your audio system configuration.
(This function does not work when the 3D PHONIC function is
activated.)

Setting options

DOLBY SURROUND, STEREO
[DOLBY SURROUND]: select when listening to multichannel

surround audio with the unit’s analog AUDIO OUT terminals
connected to a surround decoder.

[STEREO]: select when listening to conventional two-channel

stereo audio with the unit’s AUDIO OUT terminals connected
to a stereo amplifier/receiver or television set, or in case you
want to record the audio from a DVD VIDEO disc to MiniDisc,
cassette, etc.

D. RANGE CONTROL

This setting provides optimal audio quality from the analog
AUDIO OUT terminals for listening to DVD VIDEO discs recorded
in Dolby Digital format, at low or middle volume.

Setting options

WIDE RANGE, NORMAL, TV MODE
[WIDE RANGE]: when selected, audio is played back with the

widest dynamic range so that you can enjoy powerful
playback sound.

[NORMAL]: normally, select this option.
[TV MODE]: select if DVD VIDEO disc sound level is lower than

TV program sound level. Thus you can hear sound at a lower
volume clearly.

OUTPUT LEVEL

This setting allows you to attenuate the level of the signal output
from the unit’s analog AUDIO OUT terminals.

Setting options

STANDARD, LOW

• If the sound output from the speaker is distorted, select [LOW].

OTHERS menu

RESUME

You can select the resume playback mode.
See pages 8 and 9 for details about the resume playback
function.

Setting options

ON, OFF, DISC RESUME
[ON]: when selected, the unit can resume playback of the disc

from the position where playback was last interrupted, if the
disc is still in the disc tray.

[OFF]: when selected, the resume function is deactivated.
[DISC RESUME]: when selected, the unit can resume playback

of the last 30 discs played. The unit retains a memory of the
interrupted positions of the last 30 discs played, even though
they have been removed from the disc tray.

ON SCREEN GUIDE

The unit can display “on-screen guide” icons or characters on the
picture, which show what is happening to the disc or the unit.

Example of “on-screen guide” icons: , ,

Setting options

ON, OFF
[ON]: when selected, the on-screen guide is activated.

AUTO STANDBY

When the unit is stopped for more than 30 minutes or 60 minutes,
the unit enters standby mode automatically.

Setting options

60, 30, OFF

PARENTAL LOCK

When this option is selected, pressing ENTER on the remote
control unit brings up the PARENTAL LOCK display shown below.
This allows you to restrict children from playing DVD VIDEO
discs.

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

• See page 24 for details about the parental lock setting.

US

NONE

_ _ _ _

USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

Changing the

initial settings

23

Changing the initial settings

Changing t

he

initial settings

Numeric buttons

5/∞

ENTER

Limiting playback by children

This function restricts playback of DVD VIDEO discs which
contain violent (and other) scenes according to the level set by
the user. For example, if a movie which includes violent scenes
supports the parental lock feature, such scenes which you do not
want to let children view can be cut or replaced with other
scenes.

4 Press 5/∞ to select the country code.

Select the code of the country whose standards were used to
rate the DVD VIDEO disc content.
See “Appendix A: Country/Area code list for Parental Lock”
on page 29.

PARENTAL LOCK

SELECT

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

US

UG
UM

NONE

US

_ _ _ _

UY
UZ
VA
VC

USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

5 Press ENTER.

moves to [SET LEVEL].

6 Press ENTER to bring up the pull-down

menu.

In the pull-down menu, [NONE] and levels [8] to [1] are
available.
[NONE] does not restrict playback. Level [1] is the strictest
level. Discs rated higher than the selected level are restricted.

PARENTAL LOCK

SELECT

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

US

NONE
8

NONE

7

_ _ _ _

6
5
4
3

USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

To set Parental Lock for the first time

1 Bring up the OTHERS menu.
2 Press 5/∞ to move to select [PARENTAL

LOCK] then press ENTER.

The Parental Lock on-screen display appears on the TV
screen.

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

US

NONE

_ _ _ _

USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.

3 While is pointing to [COUNTRY CODE],

press ENTER to bring up the pull-down
menu.

7 Press 5/∞ to select a desired parental lock

level, then press ENTER.

moves to [PASSWORD].

8 Press the numeric buttons (0 to 9) to enter a

4-digit password.

PARENTAL LOCK

SELECT

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

US

NONE

1234

NEW PASSWORD?
TO EXIT, PRESS CHOICE.

...

PRESS 0 ~ 9 KEY

9 Press ENTER.

The parental lock feature is set.

moves to [EXIT]. Pressing ENTER again returns to the

[OTHERS] menu of the preference display.

Hint

If you want to change the password at step 8, do it before
pressing ENTER.

24

Changing the initial settings

To change the settings

You can change the parental lock settings later.

1 Bring up the OTHERS menu.
2 Press 5/∞ to move to select [PARENTAL

LOCK] and press ENTER.

The parental lock on-screen display appears on the TV
screen.

3 While is pointing to [PASSWORD], press

the numeric buttons to enter your current 4­digit password then press ENTER.

moves to [COUNTRY CODE] if you enter the correct
password.
If you enter a wrong password, “WRONG! RETRY...” appears
on the TV screen, and you cannot go to the next step.
If you forget your password, enter “8888.” The current
password is deleted and you can set a new password.

4 To change the [COUNTRY CODE] or [SET

LEVEL], press ENTER to bring up the
associated pull-down menu when is
pointing to the desired item.

5 Press 5/∞ to select the desired option then

press ENTER.

If you change the country code, you must reselect the
parental lock level.

6 While is pointing to [PASSWORD], press

the numeric buttons to enter a 4-digit
password.

The password entered in this step becomes the new
password. If you want to keep the same password as before,
enter the same password.

7 Press ENTER.

moves to [EXIT]. Pressing ENTER again returns to the
[OTHERS] menu of the preference display.

To temporarily release the Parental Lock

If the parental level is set to a strict value, some discs may not
play at all.
When you insert such a disc and try to play it, the following
parental lock on-screen display appears on the TV screen, asking
you whether you want the parental lock to be temporarily
released or not.

1 Press 5/∞ to move to [TEMPORARY

RELEASE], then press ENTER.

PARENTAL LOCK

TEMPORARY RELEASE

NOT RELEASE

PASSWORD

SELECT

_ _ _ _

USE 5∞ TO SELECT, USE ENTER TO CONFIRM

2 Press the numeric buttons (0 to 9) to enter

your 4-digit password.

The Parental Lock is released, and the unit starts playback.
If you enter a wrong password, “WRONG! RETRY...” appears
on the TV screen. Enter the correct password.

NOTE

When you enter the wrong password 3 times at step 2 above,
moves to [NOT RELEASE] automatically and 5/∞ do not work.

NOTE

If you enter the wrong password more than 3 times in step 3
above, moves to [EXIT] automatically and 5/∞ do not work.

25

Changing the

initial settings

Addit

ional

information

Additional information

7

8 9

Names of parts and controls

Front panel

1 23 7654

-=8 9 0

1 STANDBY indicator (6)
2 0 button (7)
3 7 button (7, 8)
4 3 button (7, 9)
5 8 button (8, 9)
6 4 button (9, 10)

Display window

1

1 Audio format indicators
2 Resume/Program/Random indicators
3 Group indicator
4 Title indicator
5 Track indicator

7 ¢ button (9, 10)
8 STANDBY/ON button (6)

9 Remote sensor (5)
0 Display window (see the illustration below)

- Disc tray (7)
= QUICK PLAYBACK button (9)

3 4 5 62

6 Chapter indicator
7 Repeat mode indicator
8 3(play) / 8(pause) indicators
9 Multi-information window

26

Remote control unit

Additional information

#

1
2

3

4

5
6

7

8

9
0

­=

~
!
@

DISPLAY

3D PHONIC

CHOICE

TITLE/

GROUP RETURN CANCEL

213

546

879

010 +10

ANGLE

SUB TITLE AUDIO ZOOM

TOP MENU MENU

SLOW

PREVIOUS SELECT

VFP ON SCREEN

CLEAR

STANDBY/ON

ENTER

NEXT

$
%

^

&
*
(

)
_

+

¡

1 DISPLAY button (8)
2 TITLE/GROUP button (11, 20)
3 3D PHONIC button (17)
4 Numeric buttons
5 SUBTITLE button (15)
6 ANGLE button (15)
7 TOP MENU button (7, 11)
8 Cursor selection (5 Up, ∞ Down, 2 Left, 3 Right) buttons
9 CHOICE button (7, 21)
0 ¡/SLOW + button (9)

- 1/SLOW – button (9)
= 4/PREVIOUS button (9, 10, 11, 19)
~ 3/SELECT button (7, 9, 11, 13, 19 )
! button (10)
@ 7/CLEAR button (7, 8, 13, 20)

# Infrared signal window (5)
$ STANDBY/ON button (6)

% RETURN button (11)
^ CANCEL button (13)
& AUDIO button (15)
* ZOOM button (16)
( MENU button (11)
) ENTER button
_ VFP button (16)
+ ON SCREEN button (8, 12, 14, 17, 20)
¡ ¢/NEXT button (9, 10, 11, 19)

8 button (8, 9)

27

Additional

information

Additional information

Addit

ional

information

Troubleshooting

Power

Power does not come on.

\ Power plug is not inserted securely. Plug in securely.

Operation

“REGION CODE ERROR!” is shown on the TV screen.

\ Region code of the inserted disc does not match the unit.

Check the region code of the disc printed on the disc jacket.

Operation is not possible.

\ Microcomputer malfunction due to lightning or static electricity.

Turn off the power and unplug the power cord, then connect
the power cord again.

\ Moisture condensation caused by a sudden change of

temperature or humidity. Turn off the power, then turn it on a
few hours later.

\ The disc does not allow the operation, or an unplayable disc is

inserted. Check and replace the disc (see page 2).

[LOCK] is displayed on the display window and the disc tray
does not open.

\ When you press 0 while pressing down 7 on the unit in

standby mode, the tray lock function is activated. The disc tray
cannot be opened or closed in this status. To release this
status, press 0 while pressing down 7 on the unit in standby
mode.

Picture

Picture is noisy.

\ The unit is connected to a VCR directly and the copyguard

function is activated. Connect the unit so that the picture
signal flows directly to the TV.

Picture is distorted when using COMPONENT VIDEO OUT or
S-VIDEO output jack(s).

\ Both the component connection and S-video connection are

made. Disconnect the unused one.

Audio

DVD VIDEO disc playback sound level is lower than TV
broadcast sound level.

\ Set the [D.RANGE CONTROL] preference to [TV MODE] (see

page 23).

Analog audio output is distorted.

\ Set the [OUTPUT LEVEL] preference to [LOW] (see page 23).

Sound is abnormal when DTS-encoded source is played
back.

\ Connect audio equipment with a built-in DTS decoder to the

unit.

\ Play back a source other than DTS-encoded one.

MP3

No sound comes out.

\ MP3 disc is recorded with the “packet writing.” It cannot be

played.

Files (tracks) are not played in the recorded order.

\ This unit plays the files in the alphabetic order. So, the

playback order can vary.

Specifications

Specifications and appearance are subject to change without
prior notice.

General

Readable discs DVD VIDEO, DVD-R (Video format), DVD-

Video format NTSC

Other

Power requirements

Power consumption

Mass 2.1 kg (4.7 lbs)
Dimensions (W × H × D)

Video outputs

COMPONENT (pin jacks)

VIDEO OUT (pin jack)

S-VIDEO OUT (S jack)

Horizontal resolution

Audio outputs

ANALOG OUT (pin jack)

DIGITAL OUT (COAXIAL)

DIGITAL OUT (OPTICAL)

Audio characteristics

Frequency response

Dynamic range 16 bit: More than 98 dB

Wow and flutter Unmeasurable (less than ± 0.002%)
Total harmonic distortion

• Notes for PX modes (Check the specification indication
on the rear panel.)

Power requirements AC 110 V to 240 V , 50 Hz/60 Hz
Power consumption 10 W (POWER ON), 0.7 W

• Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarkes of Dolby
Laboratories.

• “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, inc.

RW (Video format), SVCD, Video CD, Audio
CD (CD-DA), MP3 format, CD-R/RW (CD­DA, SVCD, Video CD, MP3 format)

AC 120 V , 60 Hz

10 W (POWER ON), 0.7 W (STANDBY
mode)

435 mm × 53 mm × 248.4 mm

3

/16 inch × 2-1/8 inch × 9-13/16 inch)

(17-

Y Output: 1.0 Vp-p (75 Ω)

B/PR Output: 0.7 Vp-p (75 Ω)

P

1.0 Vp-p (75 Ω)

Y Output: 1.0 Vp-p (75 Ω)
C Output: 286 mVp-p (75 Ω)

500 lines or more

2.0 Vrms (10 kΩ)

0.5 Vp-p (75 Ω termination)

–21 dBm to –15 dBm (peak)

CD (sampling frequency 44.1 kHz):

DVD (sampling frequency 48 kHz):

DVD (sampling frequency 96 kHz)

20 bit: More than 100 dB
24 bit: More than 100 dB

less than 0.006%

2 Hz to 20 kHz

2 Hz to 22 kHz
(4 Hz to 20 kHz for DTS and Dolby
Digital bitstream signals)

2 Hz to 44 kHz

(STANDBY mode)

28

Additional information

Appendix A: Country/Area code list for Parental Lock

AD Andorra

AE United Arab Emirates

AF Afghanistan

AG Antigua and Barbuda

AI Anguilla

AL Albania

AM Armenia

AN Netherlands Antilles

AO Angola

AQ Antarctica

AR Argentina

AS American Samoa

AT Austria

AU Australia

AW Arub a

AZ Azerbaijan

BA Bosnia and Herzegovina

BB Barbados

BD Bangladesh

BE Belgium

BF Burkina Faso

BG Bulgaria

BH Bahrain

BI Burundi

BJ Benin

BM Bermuda

BN Brunei Darussalam

BO Bolivia

BR Brazil

BS Bahamas

BT Bhutan

BV Bouvet Island

BW Botswana

BY Belarus

BZ Belize

CA Canada

CC Cocos (Keeling) Islands

CF Central African Republic

CG Congo

CH Switzerland

CI Côte d’Ivoire

CK Cook Islands

CL Chile

CM Cameroon

CN China

CO Colombia

CR Costa Rica

CU Cuba

CV Cape Verde

CX Christmas Island

CY Cyprus

CZ Czech Republic

DE Germany

DJ Djibouti

DK Denmark

DM Dominica

DO Dominican Republic

DZ Algeria

EC Ecuador

EE Estonia

EG Egypt

EH Western Sahara

ER Eritrea

ES Spain

ET Ethiopia

FI Finland

FJ Fiji

FK Falkland Islands

FM Micronesia (Federated

States of)

FO Faroe Islands

FR France

FX France, Metropolitan

GA Gabon

GB United Kingdom

GD Grenada

GE Georgia

GF French Guiana

GH Ghana

GI Gibraltar

GL Greenland

GM Gambia

GN Guinea

GP Guadeloupe

GQ Equatorial Guinea

GR Greece

GS South Georgia and the

South Sandwich

GT Guatemala

GU Guam

GW Guinea-Bissau

GY Guyana

HK Hong Kong

HM Heard Island and

McDonald Islands

HN Honduras

HR Croatia

HT Haiti

HU Hungary

ID Indonesia

IE Ireland

IL Israel

IN India

IO British Indian Ocean

Territory

IQ Iraq

IR Iran (Islamic Republic of)

IS Iceland

IT Italy

JM Jamaica

JO Jordan

JP Japan

KE Kenya

KG Kyrgyzstan

KH Cambodia

KI Kiribati

KM Comoros

KN Saint Kitts and Nevis

KP Korea, Democratic

People's Republic of

KR Korea, Republic of

KW Kuwait

KY Cayman Islands

KZ Kazakhstan

LA Lao People's Democratic

Republic

LB Lebanon

LC Saint Lucia

LI Liechtenstein

LK Sri Lanka

LR Liberia

LS Lesotho

LT Lithuania

LU Luxembourg

LV Latvia

LY Libyan Arab Jamahiriya

MA Morocco

MC Monaco

MD Moldova, Republic of

MG Madagascar

MH Marshall Islands

ML Mali

MM Myanmar

MN Mongolia

MO Macau

MP Northern Mariana Islands

MQ Martinique

MR Mauritania

MS Montserrat

MT Malta

MU Mauritius

MV Maldives

MW Malawi

MX Mexico

MY Malaysia

MZ Mozambique

NA Namibia

NC New Caledonia

NE Niger

NF Norfolk Island

NG Nigeria

NI Nicaragua

NL Netherlands

NO Norway

NP Nepal

NR Nauru

NU Niue

NZ New Zealand

OM Oman

PA Panama

PE Peru

PF French Polynesia

PG Papua New Guinea

PH Philippines

PK Pakistan

PL Poland

PM Saint Pierre and Miquelon

PN Pitcairn

PR Puerto Rico

PT Portugal

PW Palau

PY Paraguay

QA Qatar

RE Réunion

RO Romania

RU Russian Federation

RW Rwanda

SA Saudi Arabia

SB Solomon Islands

SC Seychelles

(for page 24)

SD Sudan

SE Sweden

SG Singapore

SH Saint Helena

SI Slovenia

SJ Svalbard and Jan Mayen

SK Slovakia

SL Sierra Leone

SM San Marino

SN Senegal

SO Somalia

SR Suriname

ST Sao Tome and Principe

SV El Salvador

SY Syrian Arab Republic

SZ Swaziland

TC Turks and Caicos Islands

TD Chad

TF French Southern

Territories

TG Togo

TH Thailand

TJ Tajikistan

TK Tokelau

TM Turkmenistan

TN Tunisia

TO Tonga

TP East Timor

TR Turkey

TT Trinidad and Tobago

TV Tuvalu

TW Taiwan

TZ Tanzania, United Republic

of

UA Ukrain e

UG Uganda

UM United States Minor

Outlying Islands

US United States

UY Uruguay

UZ Uzbekistan

VA Vatican City State (Holy

See)

VC Saint Vincent and the

Grenadines

VE Venezuela

VG Virgin Islands (British)

VI Virgin Islands (U.S.)

VN Vietnam

VU Vanuatu

WF Wallis and Futuna Islands

WS Samoa

YE Yemen

YT Mayotte

YU Yugoslavia

ZA South Africa

ZM Zambia

ZR Zaire

ZW Zimbabwe

Additional

information

29

Additional information

Addit

ional

information

)

Appendix B: Table of languages and their abbreviations

AA Afar FA Persian KM Cambodian OM (Afan) Oromo SU Sundanese

AB Abkhazian FI Finnish KN Kannada OR Oriya SV Swedish

AF Afrikaans FJ Fiji KO Korean (KOR) PA Panjabi SW Swahili

AM Ameharic FO Faroese KS Kashmir i PL Polish TA Tamil

AR Arabic FY Frisian KU Kurdish PS Pashto, Pushto TE Telugu

AS Assamese GA Irish KY Kirghiz PT Portuguese TG Tajik

AY Aymara GD Scots Gaelic LA Latin QU Quechua TH Thai

AZ Azerbaijani GL Galician LN Lingala RM Rhaeto-Romance TI Tigrinya

BA Bashkir GN Guarani LO Laothian RN Kirundi TK Turkmen

BE Byelorussian GU Gujarati LT Lithuanian RO Rumanian TL Tagalog

BG Bulgarian HA Hausa LV Latvian, Lettish RU Russian TN Setswana

BH Bihari HI Hindi MG Malagasy RW Kinyarwanda TO Tongan

BI Bislama HR Croatian MI Maori SA Sanskrit TR Turkish

BN Bengali, Bangla HU Hungarian MK Macedonian SD Sindhi TS Tsonga

BO Tibetan HY Armenian ML Malayalam SG Sangho TT Tatar

BR Breton IA Interlingua MN Mongolian SH Serbo-Croatian TW Twi

CA Catalan IE Interlingue MO Moldavian SI Singhalese UK Ukrainian

CO Corsican IK Inupiak MR Marathi SK Slovak UR Urdu

CS Czech IN Indonesian MS Malay (MAY) SL Slovenian UZ Uzbek

CY Welsh IS Icelandic MT Maltese SM Samoan VI Vietnamese

DA Danish IW Hebrew MY Burmese SN Shona VO Volapuk

DZ Bhutani JI Yiddish NA Nauru SO Somali WO Wolof

EL Greek JW Javanese NE Nepali SQ Albanian XH Xhosa

EO Esperanto KA Georgian NL Dutch SR Serbian YO Yoruba

ET Estonian KK Kazakh NO Norwegian SS Siswati ZU Zulu

EU Basque KL Greenlandic OC Occitan ST Sesotho

(for pages 15 and 22

Appendix C: Digital output signal chart

Disc type

PCM ONLY DOLBY DIGITAL/PCM STREAM/PCM

DVD with 48/44.1 kHz, 16/20/24 bit
linear PCM

DVD with 96 kHz, 16/22/24 bit
linear PCM

DVD with DTS No output DTS bitstream

DVD with Dolby Digital 48 kHz, 16 bit, stereo linear PCM Dolby Digital bitstream

DVD with MPEG Multichannel 48 kHz, 16 bit, stereo linear PCM MPEG bitstream

SVCD/Video CD/Audio CD 44.1 kHz, 16 bit, stereo linear PCM

Audio CD with DTS No output DTS bitstream

CD-R/RW with MP3 Linear PCM

48/44.1 kHz, 16 bit, stereo linear PCM

48 kHz, 16 bit, stereo linear PCM (Down sampling)

Output

(for page 23)

30

Appendix D: Glossary

Additional information

Aspect ratio

A ratio which defines the shape of the rectangular picture in a TV.
It is the width of the picture relative to the height. A conventional
TV picture is 4:3 in aspect ratio.

Bitstream

The digital form of multichannel audio data (e.g., 5.1-channel)
before it is decoded into its various channels.

Chapter/title

Chapter is the smallest division and title is the largest division on
DVD VIDEO. A chapter is a division of a title and similar to a track
for Video CD or Audio CD.

Component video

Video signals with three channels of separate information that
makes up the picture. There are some types of component video,
such as R/G/B and Y/C

Composite video

A single video signal commonly used in most consumer video
products that contains all luminance, color, and synchronization
information.

Dolby Digital (AC3)

A six-channel system consisting of left, center, right, left rear,
right rear and LFE (Low-Frequency Effect channel, for use with a
sub-woofer) channels. All processing is done in the digital
domain. Not all Dolby Digital discs contain six (5.1) channels of
information.

Dolby Surround/Dolby Pro Logic

Dolby Surround records four channels of front and rear audio in
two channels in a way that allows a decoder to recover the
original four channels for playback. Because the audio is
recorded in two channels, it can be played back naturally by a
two-channel stereo system.
Dolby Pro Logic introduces directional circuits in decoder-side
processing (increasing the level of specific channels and lowering
the level of silent channels) for greater spatial perspective, and
adds a center speaker used primarily for dialog. The result is
enhanced channel separation.

B(PB)/CR(PR).

PAL (Phase Alternation by Line)

A color television system format used extensively in Western
Europe.

PBC

PBC stands for “Playback control” and is a method of controlling
disc play for Video CDs (VCD). You are able to interact with the
disc through menus.

S-video

A video signal which improves picture quality over standard
composite connections. Used on Super VHS, DVD, high end TV
monitors, etc.

Trac k

The smallest division on SVCD, Video CD and Audio CD discs.

Down-mix

Internal stereo mix of multichannel surround audio by a DVD
player. The down-mix signals are output from analog AUDIO OUT
connectors.

DTS

A Digital Surround audio encoding format configured with six
(5.1) channels, similar to Dolby Digital. It requires a decoder,
either in the player or in an external receiver. DTS stands for
Digital Theater Systems.
Not all DTS discs contain six (5.1) channels of information.

Dynamic range

The difference between the loudest and softest sounds.

Linear PCM audio

PCM stands for “pulse code modulation.” Linear PCM is the usual
method for digitally encoding audio without compression, and is
used for the audio tracks on DVD VIDEO discs, Audio CDs, etc.

MP3

MP3 is an audio data compression format, which stands for
MPEG-1 Audio Layer 3. Using MP3, you can achieve a data
reduction of about 1:10.

NTSC (National television system committee)

A black and white and color television system format used in the
U.S.A., Canada, Mexico and Japan.

Additional

information

31

LIMITED WARRANTY

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date
of original retail purchase for the period as shown below. ("The Warranty Period")

PARTS LABOR

CONSUMER VIDEO 1-90

1 YR 90 DAYS

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service
centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen
size 25 inches and above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: [phone].

If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the
name and location of which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model number
or serial number has been altered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;

3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;

4. Damage that occurs in shipment, due to act of God, and cosmetic damage;

5. Signal reception problems and failures due to line power surge;

6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;

7. Accessories;

8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);

There are no express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT­ABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.

JVC COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information
for future reference.

Model No. : Serial No. :

Purchase data : Name of dealer :

1700 Valley Road
Wayne, NJ 07470

Authorized Service Centers

®

QUALITY

SERVICE

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1 [phone]

http://www.jvc.com

Dear Customer,
In order to receive the most satisfaction from your purchase,please read the instruction booklet before
operating the unit.In the event that repairs are necessary, please call 1 [phone] for your nearest
authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.

Do not service the television yourself

Caution

To prevent electrical shock,do not open the cabinet.There are no user serviceable
parts inside.Please refer to qualified service personnel for repairs.

Accessories

To purchase accessories for your JVC product,please call toll free:1 [phone] or
on the web at www.JVC.com

BT-51005-5
(0301)

VICTOR COMPANY OF JAPAN, LIMITED

EN.

©2003 VICTOR COMPANY OF JAPAN, LIMITED

0603KTYBICJSC

J

V

C