Enter below the Model No. and Serial No.
which are located on the rear, bottom or
side of the cabinet. Retain this information for future reference.
Model No.
Serial No.
LVT0435-001B
[J]
XV-521BK [J] EN
LVT0435-001A
Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de
l'appareil.
2. Ne pas exposer l'appareil à la pluie ni à l'humidité.
Caution –– POWER switch!
Disconnect the mains plug to shut the power off completely. The
POWER switch in any position does not disconnect the mains line. The
power can be remote controlled.
Attention –– Commutateur POWER!
Déconnecter la fiche de secteur pour couper complètement le courant.
Le commutateur POWER ne coupe jamais complètement la ligne de
secteur, quelle que soit sa position. Le courant peut être télécommandé.
IMPORTANT FOR LASER PRODUCTS
IMPORTANT POUR LES PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user service-
able parts inside the Unit; leave all servicing to qualified service
personnel.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: Radiation laser visible quand l'appareil est ouvert ou
que le verrouillage est en panne ou désactivé. Eviter une exposition
directe au rayon.
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n'y a aucune
pièce utilisable à l'intérieur. Laisser à un personnel qualifié le soin
de réparer votre appareil.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED "DIGITAL APPARATUS",
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR: "APPAREILS NUMERIQUES",
NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
XV-521BK [J] EN
LVT0435-001A
Table of contents
Introduction
Introduction
Page 1
Features .................................................................... 1
abbreviations ....................................... Appendix A
Country code list for parental lock ...... Appendix B
XV-521BK [J] EN
SLOW
UP
DOWN
LEFT
CURSOR
RIGHT
AMP
VOL
TV
VOL
TITLE
MENU
TV
ch
AUDIOSUBTITLE
CANCEL
SHIFT
TIME CHOICE
PLAY MODE
TV RETURN
DIGEST STROBE ZOOM
TV 0 TV 100+
TV 7 TV 8 TV 9
TV 4 TV 5 TV 6
TV 1 TV 2 TV 3
DISPLAY
RETURN
TV/VIDEO
ANGLE
3D-PHONIC
OPEN
/CLOSE
DVD POWER
TV POWER
THEATER
POSITION
456
789
10+100
RM-SXV521J REMOTE CONTROL
PLAY
B.SKIP
PAUSE
STOP
ENTER
F.SKIP
B.SEARCH
F.SEARCH
123
¢
4
3
7
8
LVT0435-001A
Introduction
Introduction
Features
Picture functions
7 Strobe function
The unit can display nine continuous still pictures on
the TV screen.
7 Digest function
You can select the desired title from the opening
scenes displayed on the TV screen.
7 Angle function*
Introduction
You can select a desired angle from multiple camera
angles recorded on the DVD VIDEO disc.
7 Zoom function
You can view scenes close-up.
7 Parental lock*
You can restrict the playback of DVD VIDEO discs with
scenes which you do not want children to see, such
as adult or violent films.
7 Theater position
You can select the picture character according to the
lighting of your room.
Supplied accessories
• Audio/video cable (x 1)
• S-video cable (x 1)
• AV compulink cord (x 1)
(except XV-421BK)
• Remote Control Unit (x 1)
Audio functions
7 High quality digital sound
You can enjoy high quality sound with Dolby Digital
or Linear-PCM.
7 Surround function*
The unit is compatible with Dolby Digital surround and
DTS surround.
(DTS surround is available for digital output only.)
7 3D Phonic function
You can enjoy surround sound with your 2-channel
system.
Other functions
7 Multi-language subtitles and sound*
You can select a subtitle or sound language from those
recorded on the DVD VIDEO disc.
7 Multi-disc playback
You can enjoy Audio CD discs and Video CD discs, as
well as DVD VIDEO discs.
7 Operation from the on-screen display
User-friendly on-screen displays allow you to operate
the unit easily.
• R6P(SUM-3)/AA(15F) batteries (x 2)
• Instruction manual (x 1)
• AC power cord (x 1)
Functions with (*) mark only work on a DVD VIDEO disc
that is compatible with each function.
1
XV-521BK [J] EN
LVT0435-001A
About this instruction manual
This instruction manual basically explains operations as follows:
To playback in random order [RANDOM]
You can play titles or tracks in random order by using
the Random function.
TV POWER
OPEN
THEATER
3D-PHONIC
/CLOSE
DVD POWER
POSITION
AUDIOSUBTITLE
TV/VIDEO
ANGLE
DIGEST STROBE ZOOM
123
TV 1 TV 2 TV 3
456
TV 4 TV 5 TV 6
789
TV 7 TV 8 TV 9
10+100
TV RETURN
TV 0 TV 100+
TV
AMP
SLOW
ch
VOLTVVOL
PLAY MODE
DISPLAY RETURN
CANCEL
TIME CHOICE
SHIFT
B.SEARCH
F.SEARCH
PLAY
F.SKIP
B.SKIP
3
¢
4
STOP
ENTER
PAUSE
7
8
MENU
TITLE
UP
LEFT
CURSOR
RIGHT
DOWN
REMOTE CONTROL
The number
indicates the
procedural step.
1
7
While stopped
Press PLAY MODE - CANCEL.
1
The play mode menu appears on the TV screen.
Use CURSOR 2/3 to move to
2
[RANDOM].
Introduction
These symbols
indicate the types of
discs which the
operation can be
Introduction
used for.
3
The number
indicates the
2
following procedural
step(s) in which the
button(s) is(are)
used.
You may also use the
corresponding
buttons on the front
panel of the unit if
available.
Other convenient
procedures, etc.
Additional
supplemental
remarks
REPEATPROGRAMRANDOM
The “RANDOM” indicator appears in the display
window on the front panel.
Press ENTER.
3
The unit starts random playback.
After playing all titles/tracks of the disc, random
playback ends.
The same title or track will not be played back more than once
during random play.
• To stop/quit random playback in the middle
Press STOP to stop playback. The unit is still in
random playback mode, so pressing PLAY starts
random playback again.
To quit random playback, press STOP again while
stopped. The “RANDOM” indicator in the display
window turns off.
NOTE
Some DVD VIDEO discs may not be played back correctly
in random mode.
The names of
buttons on the
remote control unit
(or on the front panel
of the unit) are all
given in uppercase
letters.
2
XV-521BK [J] EN
LVT0435-001B
Introduction
Notes on handling
Important cautions
Installation of the unit
• Select a place which is level, dry and neither too hot
nor too cold (between 5˚C and 35˚C, 41˚F and 95˚F).
• Leave sufficient distance between the unit and the TV.
• Do not use the player in a place subject to vibrations.
Power cord
• Do not handle the power cord with wet hands!
Introduction
• A small amount of power (3.0 watts) is always
consumed while the power cord is connected to the
wall outlet.
• When unplugging the player from the wall outlet,
always pull the plug, not the power cord.
To prevent malfunction of the unit
• There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord and
consult your dealer.
• Do not insert any metallic object into the unit.
• Do not use any non-standard shape disc available on
the market, because it may damage the unit.
• Do not use a disc with tape, seals, or paste on it,
because damage to the unit may result.
Note about copyright laws
• Please check the copyright laws in your country
before recording from DVD VIDEO, Audio CD, and
Video CD discs. Recording of copyrighted material
may infringe copyright laws.
Note about the copyguard system
• The DVD VIDEO disc is protected by the copyguard
system. When you connect the unit to your VCR
directly, the copyguard system activates and the
picture may not be played back correctly.
Safety precautions
Avoid moisture, water and dust
Do not place the unit in moist or dusty places.
Avoid high temperatures
Do not expose the unit to direct sunlight or place it
near a heating device.
When you’re away
When away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
Do not insert foreign objects into the unit
Do not insert wires, hairpins, coins, etc. into the unit.
Do not block the vents
Blocking the vents may damage the unit.
Care of the cabinet
When cleaning the unit, use a soft cloth and follow the
relevant instructions on the use of chemically-coated
cloths. Do not use benzene, thinner or other organic
solvents and disinfectants. These may cause
deformation or discoloring.
If water gets inside the unit
Turn off the power switch and remove the plug from
the wall outlet, then call the store where you made
your purchase. Using the unit in this state may cause a
fire or electrical shock.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
Refer to the corresponding pages indicated in () for details.
Front panel
(For XV-521BK/523GD/525BK)
1 POWER button
2 STANDBY indicator
3 Remote sensor
DVD PLAYER
STANDBY
POWER
3D PHONICSKIP
DOLBY
D I G I T A L
TITLE CHAP. RESUME
EACH
4 Disc tray
THEATER
5 0 (OPEN/CLOSE) button
6 7 (STOP) button
7 # (PLAY) button
8 8 (PAUSE) button
OPEN/CLOSE
0
PLAY
#
STOP PAUSE
7
4¢
8
SHUTTLE
1¡
DVD
/
VDEO CD / CD
Preliminary knowledge
= SHUTTLE knob
Knowledge
Preliminary
9 3D PHONIC button
(For XV-421BK)
1POWER button
2 STANDBY indicator
3 Remote sensor
XV-421 DVD PLAYER
STANDBY
POWER
DOLBY
D I G I T A L
3D PHONICSKIP
9 3D PHONIC button
1 POWER button (17)
Turns the unit on or off (standby).
2 STANDBY indicator
Lights when the power cord is connected and the unit is
on standby. When the unit is turned on, the STANDBY
indicator goes off.
3 Remote sensor
Receives the signal from the remote control unit.
4 Disc tray (17)
Used to load a disc.
5 0 (OPEN/CLOSE) button (17)
Used to open and close the disc tray.
6 7 (STOP) button (18)
Stops playback.
Also used to erase all programmed tracks for the program
play.
7 # (PLAY) button (18)
Starts playback. Also, used as a SELECT button for the PBC
of Video CDs.
8 8 (PAUSE) button (18)
Pauses playback.
0 Display window
4 Disc tray
TITLE CHAP. RESUME
THEATER
EACH
0 Display window
9 3D PHONIC button (32)
Produces a simulated surround effect.
0 Display window
Indicates the current status of the unit.
- 4/¢ (SKIP) buttons (19, 21)
Used to skip a chapter, title or track.
Also, used for the page selection of a menu screen (for
DVD VIDEO/Video CD).
Holding down 4 or ¢ during playback reverses or
advances playback rapidly.
= SHUTTLE knob (19, 25) (for XV-521BK/XV-523GD/
XV-525BK)
Performs rapid advance/reverse playback operations.
Also used for slow-motion playback of a picture (for DVD
VIDEO/Video CD).
~ 1/¡ (SEARCH) button (19, 25) (XV-421BK only)
Pressing 4 or ¢ during playback reverses or advances
playback rapidly. Each press of the button during rapid
playback increases the playback speed.
Also used for slow-motion playback of a picture (for DVD
VIDEO/Video CD).
- 4/¢ (SKIP) buttons
5 0 (OPEN/CLOSE) button
6 7 (STOP) button
7 # (PLAY) button
8 8 (PAUSE) button
OPEN/CLOSE
0
PLAY
#
STOP PAUSE
7
4¢
8
SEARCH
1¡
/
VDEO CD / CD
DVD
- 4/¢ (SKIP) buttons
~ SEARCH buttton
4
XV-521BK [J] EN
LVT0435-001A
Preliminary knowledge
Remote control unit
! Infrared signal-emitting window
Knowledge
Preliminary
0 4 (B.SKIP) - B. SEARCH button
1 3D PHONIC button
2 OPEN/CLOSE button
3 SUBTITLE - DIGEST button
4 AUDIO - STROBE button
5 Numeric buttons
6 SLOW button
7 AMP VOL button
8 SHIFT button
9 PLAY MODE - CANCEL button
- 8 (PAUSE) button
= TITLE button
~ CURSOR (5 UP, ∞ DOWN,
2
LEFT, 3 RIGHT) button
OPEN
3D-PHONIC
/CLOSE
AUDIOSUBTITLE
DIGEST STROBEZOOM
THEATER
POSITION
ANGLE
TV POWER
DVD POWER
TV/VIDEO
123
TV 1TV 2TV 3
456
TV 4TV 5TV 6
789
TV 7TV 8TV 9
10+100
TV RETURN
SLOW
SHIFT
B.SEARCH
B.SKIP
4
PAUSE
8
TV 0TV 100 +
AMP
VOLTVVOL
PLAY MODE
TITLE
LEFT CURSOR RIGHT
CANCEL
DOWN
DISPLAY RETURN
TIMECHOICE
F.SEARCH
PLAY
STOP
UP
3
F.SKIP
ENTER
7
MENU
¢
TV
ch
@ THEATER POSITION button
# DVD POWER - TV POWER button
$ TV/VIDEO button
% ANGLE - ZOOM button
^ TV ch button
& TV VOL button
* RETURN - CHOICE button
( DISPLAY - TIME button
) ¢ (F.SKIP) - F. SEARCH button
_ 3 (PLAY) button
+ ENTER button
¡ 7 (STOP) button
™ MENU button
REMOTE CONTROL
5
XV-521BK [J] EN
LVT0435-001A
Preliminary knowledge
1 3D PHONIC button (32)
Produces a simulated surround effect.
2 OPEN/CLOSE button (17)
Opens and closes the disc tray.
3 SUBTITLE - DIGEST button (23, 31)
Used to display the subtitle selection display on the TV
screen, as well as used to turn the subtitle on or off (for
DVD VIDEO).
Pressing this button while holding down the SHIFT button
displays beginning scenes of each title, chapter or track on
the TV screen (for DVD VIDEO/Video CD).
4 AUDIO - STROBE button (24, 31)
Selects the audio (for DVD VIDEO/Video CD). Pressing this
button while holding down the SHIFT button displays nine
continuous still pictures (for DVD VIDEO/Video CD).
5 Numeric buttons (10, 16)
Used to select a title or track number, as well as used to
enter a time for the Time search and a chapter number for
the Chapter search.
Also used to select a TV channel in conjunction with the
SHIFT button.
6 SLOW button (25)
Used for slow-motion playback of a picture (for DVD VIDEO/
Video CD).
7 AMP VOL button (16)
Used to control the volume of a JVC audio amplifier/
receiver.
8 SHIFT button
Used together with other buttons for activating their second
functions.
9 PLAY MODE - CANCEL button (27)
Displays an on-screen display for controlling the advanced
playback functions. Pressing this button while holding
down the SHIFT button cancels the last selection of the
program.
0 4 (B.SKIP) - B. SEARCH button (19, 21, 23)
Skips back a chapter, title or track. Also used for the page
selection of a menu screen (for DVD VIDEO/Video CD).
Holding down this button during playback reverses
playback rapidly.
Pressing the button while holding down the SHIFT button
during playback also reverses playback rapidly. If you press
the button while holding down the SHIFT button during
rapid reverse playback, the speed increases.
- 8 (PAUSE) button (18)
Pauses playback.
= TITLE button (20)
Displays the title menu of a DVD VIDEO disc on the TV
screen.
~ CURSOR (5 UP, ∞ DOWN, 2 LEFT, 3 RIGHT) buttons
Used to select an item form a menu or on-screen display,
or to change the setting of an item in the on-screen display.
! Infrared signal-emitting window
Point this window toward the remote sensor on the front
panel when pressing buttons.
@ THEATER POSITION button (32)
Selects a picture character from 4 options (for DVD VIDEO/
Video CD).
# DVD POWER - TV POWER button (17)
Turns the unit on or off (standby). Pressing this button while
holding down the SHIFT button turns the TV on or off.
$ TV/VIDEO button (16)
Switches the TV input mode.
% ANGLE - ZOOM button (26, 30)
Changes camera angles during playback of a DVD VIDEO
disc containing multiple camera angles. Pressing this
button while holding down the SHIFT button zooms in the
picture (for DVD VIDEO/Video CD).
^ TV ch button (16)
Changes the TV channels.
& TV VOL button (16)
Adjusts the TV volume.
* RETURN - CHOICE button (20, 35)
Returns to the previous menu (for DVD VIDEO/Video CD).
Pressing this button while holding down the SHIFT button
displays Preference on-screen display on the TV screen.
( DISPLAY - TIME button (33, 34)
Displays the status information (only for DVD disc) or the
time information (for any disc types). When the time
information appears, pressing this button while holding
the SHIFT button changes the time mode.
) ¢ (F.SKIP) - F. SEARCH button (19, 21, 23)
Skips forward a chapter, title or track. Also used for the
page selection of a menu screen (for DVD VIDEO/Video CD).
Holding down this button during playback advances
playback rapidly.
Pressing the button while holding down the SHIFT button
during playback also advances playback rapidly. If you
press the button while holding down the SHIFT button
during rapid advance playback, the speed increases.
_ 3 (PLAY) button (18)
Starts playback. Also used as a SELECT button for PBC of
Video CDs.
+ ENTER button
Executes the selected item in a menu or on-screen display.
¡ 7 (STOP) button (18)
Stops playback.
Also used to erase all the programmed tracks for the
program play.
™ MENU button (20)
Displays a DVD menu on the TV screen.
Knowledge
Preliminary
6
XV-521BK [J] EN
LVT0435-001A
Preliminary knowledge
Display window
3D-PHONIC
TITLE CHAP.
TRACK
1 Title/chapter/track indicator
3 Disc indicator
4 Function indicator
PROGRAM
DVD VCD
EACH
REMAIN
RANDOM
RESUME
2 Time display
REPEAT 1A-B
THEATER
1 Title/chapter/track indicator
Displays title/chapter, or track number.
2 Time display
Shows the cumulative or remaining time of the track or
disc, or the total disc time.
3 Disc indicator
Indicates the type of the disc set in the tray. When a DVD
VIDEO or Video CD disc is set, “DVD” or “VCD” is indicated.
When an Audio CD is set, there is no indication.
4 Function indicator
Activated function indicators light up.
Knowledge
Preliminary
Rear panel
(For XV-521BK/523GD/525BK)
(For XV-421BK)
6 DIGITAL OUT jacks (OPTICAL/COAXIAL)
7 COMPONENT VIDEO OUT jacks (Y/P
COAXIAL
S-VIDEO VIDEO
VIDEO OUT
COMPONENT
Y
AUDIO OUT
P
RPB
RL
AV COMPU LINK
DIGITAL OUT
PCM/STREAM
OPTICAL
3 AUDIO OUT jacks
(LEFT/RIGHT)
2 VIDEO OUT jack
1 S-VIDEO OUT jack
6 DIGITAL OUT jack (COAXIAL)
7 COMPONENT VIDEO OUT jacks (Y/P
DIGITAL OUT
PCM/STREAM
COAXIAL
VIDEO OUT
COMPONENT
P
RPBY
B/PR)
4 AV COMPU LINK jacks
B/PR)
AC IN
1
5AC IN connector
AC IN
1
VIDEO OUT
S-VIDEO VIDEO
2 VIDEO OUT jack
1 S-VIDEO OUT jack
1 S-VIDEO OUT jack (12)
Outputs an S-video signal.
2 VIDEO OUT jack (12)
Outputs a composite video signal.
3 AUDIO OUT jacks (L/R) (12)
Output stereo analog audio signals.
4 AV COMPU LINK jacks (41) (except XV-421BK)
Connect with other JVC equipment supporting the AV
Compulink function to facilitate integrated operations.
7
RL
AUDIO OUT
3 AUDIO OUT jacks (LEFT/RIGHT)
5 AC IN connector (14)
Connects to the wall outlet using the supplied AC power
cord.
6 DIGITAL OUT jacks (14)
Output digital audio signals. You must select the signal type
correctly according to the external device connected to via
the Preference display. The XV-521BK/523GD/525BK
provides both the OPTICAL and COAXIAL connectors, while
XV-421BK provides only the COAXIAL connector.
7 COMPONENT VIDEO OUT jacks (Y/PB/PR) (13)
Output component video signals.
5AC IN connector
XV-M555BK [J] EN
MENU LANGUAGE
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
AUDIO DISPLAY SYSTEM
LANGUAGE
PRESS KEY
MONITOR TYPE
4:3LB
OFF
ON
EXIT
SCREEN SAVER
ON SCREEN GUIDE
AUDIO DISPLAY SYSTEM
LANGUAGE
PRESS KEY
Country Code
US
—
----
EXIT
Set Level
PASS WORD
PRESS KEY ENTER
PARENTAL LOCK
LVT0391-001A
Operational Principles
On-screen displays
The unit provides several on-screen displays.
With some displays, you can set or select preferences
or functions, while the others are display-only.
Opening displays
The Opening display appears automatically in some
conditions.
At the bottom, the following information are indicated
depending on the unit’s status.
• NOW READING: The unit is now reading the disc
information (TOC).
• REGION CODE ERROR!: The DVD VIDEO disc loaded
cannot be played because the region code of the
disc does not match the unit.
• OPEN: The disc tray is now opening.
• CLOSE: The disc tray is now closing.
Opening display
NOW READING
Preliminary knowledge
Knowledge
Preliminary
Preference displays
When the unit is stopped, pressing the RETURNCHOICE button while holding the SHIFT button
accesses the preference display for setting the
preferences.
There are four pages: LANGUAGE, AUDIO, DISPLAY
and SYSTEM as shown in the right.
See page 35 for detailed information.
PARENTAL LOCK displays
When no disc is inserted or a DVD VIDEO disc is
stopped, pressing the ENTER button while holding
down the SHIFT button accesses the PARENTAL LOCK
display in which you can set the level for limiting
playback.
See page 39 for detailed information.
LANGUAGEAUDIO
LANGUAGE
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
PRESS KEY
DISPLAYSYSTEM
LANGUAGE
AUTO STANDBY
RESUME
AV COMPULINK MODE
*
PRESS KEY
* The “AV COMPULINK
MODE” selection is not
available with the XV421BK.
PARENTAL LOCK
AUDIO DISPLAY SYSTEM
AUDIO DISPLAY SYSTEM
DOLBY
/PCM
DIGITAL
Lo / Ro
ON
EXIT
OFF
OFF
DVD 1
EXIT
8
XV-M555BK [J] EN
REPEATPROGRAMRANDOM
CD CONTROL
REPEAT A-B REPEAT TIME SEARCH
1 00:08
TRACK TIME
EACH
REMAIN
LVT0391-001A
Preliminary knowledge
Play mode displays
Pressing the PLAY MODE button accesses the play
mode display in which you can control playback
functions.
Different displays appear depending on the disc type
and the unit’s status.
While stoppedDuring DVD VIDEO playback
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
During Audio CD playbackDuring Video CD playback
VCD CONTROL
REPEAT A-B REPEAT TIME SEARCH PBC CALL
Knowledge
Status displays
Preliminary
Pressing the DISPLAY-TIME button during playback
accesses the status display.
For a DVD VIDEO disc, pressing the DISPLAY-TIME
button toggles between the DVD VIDEO function status
display, and the disc/time display and off.
For a Video CD or Audio CD disc, pressing the DISPLAYTIME button switches the disc/time display on and off.
To prevent the monitor from burning out [SCREEN SAVER]
A television monitor screen may be burned out if a
static picture is displayed for a long time. To prevent
this, the unit automatically activates the screen saver
function if a static picture, such as an on-screen display
or menu, is displayed for over 5 minutes.
DVD VIDEO function statusDisc/time (DVD VIDEO )
1 / 21 / 21 / 2
ENGLISH ENGLISH
Disc/time (Audio CD/Video CD
without PBC)
DVD/Video CD/CD PLAYER
TITLE CHAP.TIMEBITRATE
1252:25:253.3
Disc/time
(Video CD with PBC)
TRACK TIME
1 25:25 PBC
Mbps
• Pressing any button on the unit or the remote
control unit will release the screen saver function
and return to the previous display.
• You can select one of several screen saver modes
available (see page 37).
• The screen saver function is not activated during
Audio CD playback or after stopping Audio CD
playback.
9
XV-M555BK [J] EN
DIGESTSTROBEZOOM
LVT0391-001A
On-screen guide icons
Preliminary knowledge
During DVD playback, you may see icons displayed over the picture. These
have the following meanings.
: Displayed at the beginning of a scene recorded from multiple angles. (See
page 30.)
: Displayed at the beginning of a scene recorded with multiple audio
languages. (See page 31.)
: Displayed at the beginning of a scene recorded with multiple subtitle
languages. (See page 31.)
How to use numeric buttons
123
TV 1TV 2TV 3
456
TV 4TV 5TV 6
789
TV 7TV 8TV 9
10+100
TV RETURN
TV 0TV 100+
You can set the unit not to display on-screen icons above via the preference
settings described on page 38.
About invalid operation icon
When you press a button, if the unit does not accept its operation, appears
on your television screen. Operations are occasionally unacceptable even if
is not displayed.
Note that some operations may not be accepted. For example, some discs
may not allow rapid advance/reverse or slow-motion playback.
To select a track/title number
• To select a number between 1 and 10
Press the corresponding button for the number.
• To select a number higher than 10
Use the +10 button.
Examples:
To select 13+10 → 3
To select 34+10 → +10 → +10 → 4
To select 40+10 → +10 → +10 → 10
Knowledge
Preliminary
To enter a time or chapter number
The method for entering a time for Time search or chapter number for Chapter
search is different from above. See the corresponding sections in this manual
for the details.
To select a TV channel.
Press the corresponding numeric buttons (between 0 and 9) while holding
down the SHIFT button.
10
XV-M555BK [J] EN
LVT0391-001A
Preliminary knowledge
About discs
Playable disc types
Playable and non-playable disc types are as follows:
Playable discs
DVD VIDEOVideo CDAudio CD
The DVD VIDEO Logo is a trademark.
• CD-R and CD-RW discs recorded with the audio CD format can be played back, though some may not be played
back because of the disc characteristics or recording condition.
Knowledge
Preliminary
• DVD VIDEO players and DVD VIDEO discs have their own Region Code numbers. This unit only can play back DVD
VIDEO discs whose Region Code numbers include “1”.
Examples of playable DVD VIDEO discs:
2
ALL
This unit accommodates the NTSC television system and can playback discs recorded with the NTSC system. Note
that the unit cannot playback discs recorded with the PAL system.
• Playing back discs listed as “Non-playable discs” above may generate noise and damage speakers.
• This unit can play back audio recorded in CD-G, CD-EXTRA and CD-TEXT discs.
Disc structure
A DVD VIDEO disc is comprised of “titles,” while an Audio CD, Video CD is comprised of “tracks.” Each title may be
divided into some “chapters.” For example, if a DVD VIDEO disc contains some movies, each movie may have its own
title number, and each movie may be divided into some chapters. In a DVD VIDEO karaoke disc, each song usually has
its own title number and does not have chapters. In general, each title has independent content, while each chapter in
the same title has continuity.
(Example: DVD VIDEO disc)
Title 1Title 2
Chapter 1Chapter 2Chapter 3Chapter 1Chapter 2
(Example: Audio CD/Video CD)
Track 1Track 2Track 3Track 4
11
EN04-11.XV-521BK[J]00.3.27, 10:39 AM11
XV-521BK [J] EN
LVT0435-001A
Getting started
Getting started
Connections
*In the following description, “TV” may be substituted with “monitor” or “projector.”
*Before using the unit, you have to connect the unit to a TV and/or amplifier.
*In the following connection examples, the rear panel drawing of the unit is based on XV-521BK/523GD/525BK. The
XV-421BK rear panel looks different.
Before making any connections
• Do not connect the AC power cord until all other connections have been made.
• Since different components often have different terminal names, carefully read the instructions supplied with the
component you are going to connect.
To connect to a TV
You can enjoy using the unit by simply connecting it to a TV. To improve audio sound quality, connect the audio
outputs to your separate audio equipment. (See the following pages.)
* If the TV has an AV COMPU LINK terminal,
you can use the AV COMPU LINK function
(except XV-421BK).
See “AV COMPU LINK remote control
system” on page 41 for details.
S-video cable
(supplied)
DIGITAL OUT
PCM/STREAM
OPTICAL
COAXIAL
VIDEO OUT
COMPONENT
Y
The unit
R
P
B
P
AV COMPU LINK
started
Getting
S-VIDEO VIDEO
Yellow
RL
AUDIO OUT
Red
White
Yellow
White
TV
IN
S-VIDEO
VIDEO
LEFT
AUDIO
RIGHT
Red
Audio/video cable
(supplied)
: except XV-421BK
Connect the unit to a TV equipped with stereo audio input and video input jacks using the supplied audio/video
cables.
• If your TV has a monaural audio input instead of stereo, you need to use an optional audio cable which converts
stereo audio output to monaural.
• If your TV has an S-video input, you should connect it with the S-VIDEO output of the unit using the supplied Svideo cable in addition to the (standard) video connection to get better picture quality.
NOTES
• Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a VCR may
cause a monitor problem when playing back a copy-protected disc.
• Connect the unit to an NTSC television. Do not connect the unit to a PAL television.
12
XV-521BK [J] EN
LVT0435-001A
Getting started
To connect to a TV with the component video input jacks
You can enjoy high picture quality by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT
VIDEO IN jacks of your TV with the video cables.
OPTICAL
started
Getting
• Connect “Y” to “Y,” “P
NOTES
• When the component video input jacks of the TV are of the BNC type, use an adapter to convert the pin jacks to BNC jacks
(optional).
• If you do not connect the unit with the S-video cable, some functions of your TV may not work.
• Connect the unit to an NTSC television. Do not connect the unit to a PAL television.
Green
Blue
Red
DIGITAL OUT
PCM/STREAM
COAXIAL
S-VIDEO VIDEO
VIDEO OUT
COMPONENT
RL
AUDIO OUT
RPBY
P
: except XV-421BK
B” to ”PB,” and “PR” to “PR” correctly.
Component video
cable (not supplied)
The unit
AV COMPU LINK
WhiteRed
Audio cable
(not supplied)
S-video cable
(supplied)
White
Red
TV
IN
S-VIDEO
VIDEO
LEFT
RIGHT
AUDIO
Blue
RedGreen
YPBP
R
IN
To connect to an audio amplifier or receiver
You can enjoy high-quality audio by connecting the unit's audio output to your amplifier or receiver.
The unit
DIGITAL OUT
PCM/STREAM
OPTICAL
COAXIAL
S-VIDEO VIDEO
VIDEO OUT
COMPONENT
Red
RPBY
P
RL
AUDIO OUT
AV COMPU LINK
White
Audio cable
(not supplied)
• Connect the unit's AUDIO OUT to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier or
receiver.
13
: except XV-421BK
Amplifier or receiver
White
Red
IN
LEFT
AUDIO
RIGHT
Loading...
+ 36 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.