JVC X-D401S User's Guide
AUDIO / VIDEO CONTROL RECEIVER
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
RX-D401S / RX-D402B
INSTRUCTIONS
LVT1436-001A
[J]
Warnings, Cautions, and Others
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
For U.S.A
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
Mises en garde, précautions et indications diverses
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution–– STANDBY/ON button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON button in any position does not disconnect the
mains line. The power can be remote controlled.
Attention—Touche STANDBY/ON!
Déconnectez la fiche d’alimentation secteur pour couper
l’alimentation complètement. La touche STANDBY/ON,
dans n’importe quelle position, ne déconnecte pas le système
du secteur. L’alimentation ne peut pas être télécommandé.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
For U.S.A
Declaration of Conformity:
Trade Name: JVC
Model Number: RX-D401S/RX-D402B
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party: JVC Americas Corp.
Address: 1700 Valley Road, Wayne
New Jersey 07470
Telephone Number: 973-317-5000
For Canada/pour le Canada
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance
from your unit, and retain this manual for future reference.
Features
Hybrid Feedback Digital Amplifier
RX-D401S/RX-D402B features the JVC-exclusive Hybrid
Feedback Digital Amplifier. Premium-grade parts and devices,
and special internal construction assure you will enjoy superior
sound.
Compatible with HDMI*
The HDMI (High Definition Multimedia Interface) is the standard
interface for the next-generation TV. By connecting the source
components, this receiver, and TV with the HDMI cables, digital
video signals and audio signals (including Dolby Digital, DTS)
are transmitted through the cables. You can enjoy digital video
and sound without AD/DA conversion with easy connection.
As RX-D401S/RX-D402B supports up to HDMI version 1.1, this
receiver can digitally transmit 5.1-channel PCM with sampling
rates of 96 kHz and 2-channel PCM with sampling rates of 192
kHz. (These PCM signals are referred to as “multi channel
PCM” in this instruction.) You can enjoy digital sound without
deterioration. In addition, this receiver is compatible with
HDCP** (High-Bandwidth Digital Content Protection), and
HDCP contents can be viewed if you connect a HDCPcompatible TV to this receiver.
* HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
** HDCP is the abbreviation of “High-Bandwidth Digital Content
Protection,
licenced by Digital Content Protection, LLC.
” and is the high-reliable copy control technology
Precautions
Power sources
• When unplugging the receiver from the wall outlet, always pull
the plug, not the AC power cord.
• Do not handle the AC power cord with wet hands.
• If you are not going to operate the receiver for an extended
period of time, unplug the AC power cord from the wall outlet.
Ventilation
The seven high power amplifiers built in this receiver will generate
heat inside the cabinet.
For safety, observe the following carefully:
• Make sure there is good ventilation around the receiver. Poor
ventilation could overheat and damage the receiver.
• Do not block the ventilation openings or holes. (If the ventilation
openings or holes are blocked by a newspaper or cloth, etc., the
heat may not be able to get out.)
Others
• Should any metallic object or liquid fall onto the unit, unplug the
unit and consult your dealer before operating any further.
• Do not use this receiver in a bathroom or places with water.
• Do not place any containers filled with water or liquids (such as
cosmetics or medicines, flower vases, potted plants, cups, etc.)
on top of this receiver.
• Do not disassemble the unit since there are no user serviceable
parts inside.
If anything goes wrong, unplug the AC power cord and consult
your JVC dealer.
7.1 channel DAP (Digital Acoustic Processor)
Sound field simulation technology allows precise ambience
recreation of existing theatres and halls. Thanks to the highperformance DSP (Digital Signal Processor) and high-capacity
memory, you can enjoy 7.1-channel surround by playing 2channel or multi-channel software.
DCDi technology
DCDi (Directional Correlational Deinterlacing) technology,
developed by Faroudja, eliminates jagged edges generated in
progressive scan conversion. With DCDi, you can enjoy clear
and smooth video images on your display. For RX-D401S/RXD402B, this function is applied only when the NTSC analog
video signals are transmitted to the receiver.
1
Table of Contents
Parts identification ................................................ 3
Getting started ...................................................... 6
Before Installation .................................................................. 6
Checking the supplied accessories ....................................... 6
Putting batteries in the remote control ................................... 6
Connecting the FM and AM antennas ................................... 7
Connecting the speakers ....................................................... 8
Connecting video components .............................................. 9
Connecting the power cord .................................................. 14
USB connection ................................................................... 15
Basic operations ................................................. 16
1Turn on the power ............................................................ 16
2 Select the source to play.................................................. 16
3 Adjust the volume ............................................................ 17
Selecting the digital decode mode ....................................... 18
Tu r ning off the sounds temporarily ...................................... 18
Changing the display brightness.......................................... 18
Tu r ning off the power with the Sleep Timer ......................... 19
Basic settings ...................................................... 20
Setting the speaker information easily
—Quick Speaker Setup ................................................. 20
Basic setting items ............................................................... 21
Operating procedure ............................................................ 22
Setting the speakers ............................................................ 22
Activating the EX/ES/PLIIx setting—EX/ES/PLIIx ............... 24
Selecting the main or sub channel—DUAL MONO ............. 24
Setting bass sound .............................................................. 24
Using the Midnight mode—MIDNIGHT MODE .................... 25
Setting the digital input (DIGITAL IN) terminals
—DIGITAL IN 1/2/3 ........................................................ 25
Setting the Audio delay level—AUDIO DELAY .................... 26
Memorizing the volume level for each source
—ONE TOUCH OP ....................................................... 26
Selecting the source for HDMI terminal and COMPONENT
VIDEO jacks—HDMI SELECT/CMPNT SELECT ......... 26
Selecting the output video signals—VIDEO OUTPUT ........ 26
Sound adjustments ............................................. 27
Basic adjustment items ........................................................ 27
Operating procedure ............................................................ 27
Adjusting the speaker output levels ..................................... 28
Adjusting the equalization patterns
—D EQ 63Hz/250Hz/1kHz/4kHz/16kHz........................ 28
Adjusting the bass sounds ................................................... 29
Adjusting the sound parameters for the
Surround/DSP modes ................................................... 29
Tuner operations ................................................. 31
Tuning in to stations manually .............................................. 31
Using preset tuning .............................................................. 31
Selecting the FM reception mode ........................................ 32
Creating realistic sound fields ........................... 33
Reproducing theater ambience ........................................... 33
Introducing the Surround modes ......................................... 33
Introducing the DSP modes ................................................. 35
Using the Surround/DSP modes ......................................... 36
Activating the Surround/DSP modes ................................... 37
AV COMPU LINK remote control system .......... 38
Operating other JVC products ........................... 40
Operating other manufacturers’ products ........ 42
Troubleshooting .................................................. 45
Specifications ...................................................... 47
2
A/V CONTROL RECEIVER
REMOTE CONTROL RM-SRXD401J
TV/VIDEO
AUDIO
TV
DBS/CATV
DVR/DVD
FM
USB
VCR
TV
DBS
DVR/DVD
AM
VCR
TV VOL
CHANNEL
VOLUME
MUTING
TUNING/REW
FF/TUNING
SETTING DVD MENU
ADJUST
EXIT
AUDIO INPUT
VIDEO INPUT
DECODE MODE
D.EQ FREQ
D.EQ LEVEL
C.TONE SLEEP
EFFECT
LIVENESS
TEST
L – FRONT – R
L – SURR – R
CENTER
SUBWFR
L – S. BACK – R
1
2
3
4
5
6
7
89
10
0
10
RETURN
B.BOOST MEMORY
FM MODE
DIMMER
100
DVR
DVD
MIDNIGHT
EX/ES/PL x
SURROUND
SET
8
2
3
;
5
6
7
l
1
4
9
p
e
r
h
g
f
d
s
o
t
y
i
u
q
w
j
k
a
Remote control
Parts identification
See pages in parentheses for details.
1 TV/VIDEO button (40, 42)
2 Standby/on buttons (16, 40– 44)
AUDIO, TV , DBS/CATV , VCR , DVR/DVD
3 Source selecting buttons (16, 31, 40– 44)
TV, DBS, VCR, DVR/DVD, FM, AM, USB
4 TV VOL (volume) +/– button (40, 42)
5 CHANNEL +/– button (40– 44)
6 • Operating buttons for video components (40, 41, 43, 44)
, 3, REW, 4, 7, 8, FF, ¢
• Operating buttons for tuner (31, 32)
( TUNING, TUNING 9
7 SETTING button (20, 22)
8 • Cursor buttons* (3, 2, 5, ∞) (20, 22, 27, 41, 44)
• SET button* (20, 22, 27, 41, 44)
9 ADJUST button (27)
p VIDEO INPUT button (17)
q AUDIO INPUT button (16)
w DECODE MODE button (18)
e EX/ES/PLIIx button (24)
r Adjusting buttons for Digital Equalizer (28)
D.EQ FREQ, D.EQ LEVEL +/–
t Adjusting buttons for Surround/DSP modes’ parameters
C (center).TONE, EFFECT, LIVENESS (29, 30)
y Adjusting buttons for speaker and subwoofer output levels (28)
FRONT L +/–, FRONT R +/–, CENTER +/–, SUBWFR +/–,
SURR L +/–, SURR R +/–, S.BACK L +/–, S.BACK R +/–
u SURROUND button (37)
i VOLUME +/– button (17)
o DVR/DVD mode selector (41, 44)
; MUTING button (18)
a DVD MENU button* (41, 44)
s EXIT button (20, 22, 27)
d • Numeric buttons (32, 40– 44)
1 – 10, 0, +10, 100+
• RETURN button (40)
• FM MODE button (32)
f MEMORY button (31)
g DIMMER button (18)
h B (bass).BOOST button (29)
j SLEEP button (19)
k MIDNIGHT button (25)
l TEST button (28)
* These buttons can be used for operating a JVC DVD recorder
or DVD player with the mode selector set to “DVR” or “DVD”
(see page 41).
If these buttons do not function normally, use the remote control
supplied with your DVD recorder or DVD player. Refer also to
the manuals supplied with the DVD recorder or DVD player for
details.
• When operating a DVD recorder (for JVC products
ONLY), set the mode selector (o) to “DVR.”
• When operating a DVD player, set the mode selector (o)
to “DVD.”
To open the cover of the remote
control, push here then slide
downward.
3
See pages in parentheses for details.
AUDIO/VIDEO CONTROL RECEIVER
STANDBY/ON
DIMMER
SETTING ADJUST SURROUND
DVR / DVD VCR DBS TV USB FM/AM
SOURCE
SELECTOR
/ MULTI JOG
MASTER
VOLUME
SET / TUNER PRESET
PHONES USB
HDMI
45 6
qer
89 p
321 7
w
DIGITAL EQ
LINEAR PCM
L
LSSBRS
S.WFR
PL
NEO : 6
DSP
3D-PHONIC
LFE
CR
96 / 24
AUTO SURR
C.TONE
VIRTUAL SB
B.BOOST
TUNED
STEREO
SLEEP
AUTO MUTING
INPUT ATT
HEADPHONE
MHz
kHz
x
MIDNIGHT
DIGITAL
DIGITAL AUTO
ANALOG
DUAL MONO
SBSSB
ONE TOUCH OPERATION
CC CONVERTER 1 2
1 2 3 76
%@#~!
-
=$
45 0
98
^&*(
Front panel
1 STANDBY/ON button and standby lamp (16)
2 DIMMER button (18)
3 SETTING button (20, 22)
4 ADJUST button (27)
5 SURROUND button (37)
6 HDMI lamp (9)
7 Source lamps
DVR/DVD, VCR, DBS, TV, USB, FM/AM
Display window
8 • SET button (20, 22, 27)
• TUNER PRESET button (32)
9 • SOURCE SELECTOR (16, 32)
• MULTI JOG (20, 22, 27, 32, 37)
p MASTER VOLUME control (17)
q PHONES jack (17)
w USB terminal (15)
e Display window (see below)
r Remote sensor (6)
1 ANALOG indicator (17)
= Digital signal format indicators (18, 33, 34)
2 DUAL MONO indicator (24)
3 AUTO SURR (surround) indicator (37)
4 HEADPHONE indicator (17, 35)
5 Tuner operation indicators (31)
TUNED, STEREO
6 DIGITAL EQ indicator (28)
7 AUTO MUTING indicator (32)
8 C (center).TONE indicator (30)
9 ONE TOUCH OPERATION indicator (26)
0 INPUT ATT (attenuate) indicator (29)
- SLEEP indicator (19)
~ Signal and speaker indicators (19)
! NEO:6 indicator (34)
@ VIRTUAL SB indicator (36)
# 3D-PHONIC indicator (34, 35)
$ DSP indicator (35)
% and indicator (33 – 36)
^ Main display
& B (bass).BOOST indicator (29)
* MIDNIGHT indicator (25)
( Frequency unit indicators
4
DIGITAL AUTO, LINEAR PCM, , , 96/24
MHz (for FM stations), kHz (for AM stations)
Rear panel
AV
COMPU LINK-
III
Y
P
B
P
R
COMPONENT VIDEO
VIDEO
AUDIO
MONITOR
OUT
DVR/DVD
IN
TV
IN
DBS
IN
OUT(REC) IN(PLAY)
VCR DVR
OUT(REC)
DVR/DVD
IN(PLAY)
VCR(DBS)
IN
MONITOR
OUT
DVR
OUT(REC)
VCR
OUT(REC) IN(PLAY)
DBS
IN
DVR/DVD
IN(PLAY)
VIDEO
S-VIDEO
L
R
DIGITAL IN
2(DBS)
1(DVR/DVD)
LEFTRIGHT LEFTRIGHT
LEFTRIGHT
ANTENNA
COAXIAL
AM LOOP
FM 75
AM EXT
SUBWOOFER
OUT
3(VCR)
DIGITAL OUT
PCM/STREAM
SURROUND
SPEAKERS
CAUTION:SPEAKER
IMPEDANCE 6
-
16
SURROUND BACK
SPEAKERS
DVD
MULTI IN
FRONT
CENTER
SUBWOOFER
SURR-L
SURR-R
CENTER
SPEAKER
FRONT
SPEAKERS
VCR(DBS) IN
DVR/DVD IN MONITOR OUT
HDMI
134
6
7
89p w
5
2
q
1 Power cord (14)
2 HDMI terminals (9)
VCR (DBS) IN, DVR/DVD IN, MONITOR OUT
3 AV COMPU LINK-III terminals (38)
4 DIGITAL IN terminals (14)
• Coaxial: 1(DVR/DVD)
• Optical: 2(DBS)
• Optical: 3(VCR)
5 DIGITAL OUT terminal (14)
6 ANTENNA terminals (7)
7 SUBWOOFER OUT jack (8)
8 VIDEO jacks (10 – 13)
VIDEO (composite video) jacks, S-VIDEO jacks
• Input: DBS IN, VCR IN (PLAY), DVR/DVD IN (PLAY)
• Output: VCR OUT (REC), DVR OUT (REC), MONITOR OUT
9 COMPONENT VIDEO (Y, PB, PR) jacks (10 – 13)
VCR (DBS) IN, DVR/DVD IN, MONITOR OUT
p AUDIO jacks (10 – 13)
• Input: TV IN, DBS IN, VCR IN (PLAY), DVR/DVD IN (PLAY)
• Output: VCR OUT (REC), DVR OUT (REC)
q DVD MULTI IN jacks (11)
CENTER, SUBWOOFER, SURR – L, SURR – R
w Speakers terminals (8)
SURROUND BACK SPEAKERS, SURROUND SPEAKERS,
CENTER SPEAKER, FRONT SPEAKERS
5
Getting started
123
Before Installation
General precautions
• Be sure your hands are dry.
•Turn the power off to all components.
• Read the manuals supplied with the components you are going
to connect.
Locations
• Install the receiver in a location that is level and protected from
moisture and dust.
• The temperature around the receiver must be between –5˚C
and 35˚C (23˚F and 95˚F).
• Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
• Leave sufficient distance between the receiver and the TV.
Handling the receiver
• Do not insert any metal object into the receiver.
• Do not disassemble the receiver or remove screws, covers, or
cabinet.
• Do not expose the receiver to rain or moisture.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• When you are away on travel or otherwise for an extended
period or time, remove the plug from the wall outlet. A small
amount of power is always consumed while the power cord is
connected to the wall outlet.
Putting batteries in the remote control
Before using the remote control, put two supplied batteries first.
1
Press and slide the battery cover on the back
of the remote control.
2
Insert batteries.
Make sure to match the polarity: (+) to (+) and (–) to (–).
3
Replace the cover.
If the range or effectiveness of the remote control decreases,
replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell
batteries.
• Supplied butteries are for initial setup. Replace for continued
use.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
When using the remote control, aim the remote control directly at
the remote sensor on the front panel.
Remote sensor
The receiver has a built-in cooling fan which operates
while the receiver is turned on. Be sure to leave enough
ventilation to obtain sufficient cooling effect.
CAUTION:
Do not connect the AC power plug to the wall outlet until all
connections are completed.
Checking the supplied accessories
Check to be sure you have all of the following supplied
accessories. If anything is missing, contact your dealer
immediately.
• Remote control (× 1)
• Batteries (× 2)
• AM loop antenna (× 1)
• FM antenna (× 1)
6
ANTENNA
COAXIAL
FM 75
AM EXT
AM LOOP
ANTENNA
Connecting the FM and AM antennas
Do not connect the AC power plug to the wall outlet until all connections are completed.
AM loop antenna
(supplied)
Snap the tabs on the
loop into the slots of
the base to assemble
the AM loop antenna.
If FM reception is poor, connect an
outdoor FM antenna (not supplied).
If AM reception is poor, connect
an outdoor single vinyl-covered
wire (not supplied).
AM antenna connection
Connect the AM loop antenna supplied to the AM LOOP terminals.
Connect the white cord to the AM EXT terminal, and connect the
black cord to the H terminal.
Tu rn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinyl-covered
wire (not supplied) to the AM EXT terminal. Keep the AM loop
antenna connected.
FM antenna connection
Connect the FM antenna supplied to the FM 75 Ω COAXIAL
terminal as a temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable with a
connector, disconnect the supplied FM antenna.
FM antenna (supplied)
NOTES
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown on the
right.
• Make sure the antenna conductors do not touch
any other terminals, connecting cords and power
cord. This could cause poor reception.
7
FL
FR
SL
SR
SBL
C
SW
SBR
(*SB)
LEFTRIGHT LEFT
RIGHT
LEFTRIGHT
SUBWOOFER
OUT
SURROUND
SPEAKERS
CAUTION:SPEAKER
IMPEDANCE 6
-
16
SURROUND BACK
SPEAKERS
CENTER
SPEAKER
FRONT
SPEAKERS
Connecting the speakers
12 3
+
–
1
2
+
–
1324
Do not connect the AC power plug to the wall outlet until all connections are completed.
Speaker Layout Diagram
Right surround
back speaker
(SBR)
*Left surround
back speaker
(SBL)
Right surround
speaker (SR)
CAUTIONS:
• Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals (6 Ω – 16 Ω).
• DO NOT connect more than one speaker to one speaker
terminal.
Connecting the speakers
Turn off all components before making connections.
Connecting the center speaker and the front speakers
Center
speaker (C)
Powered
subwoofer
(SW)
Left surround
speaker (SL)
Right front
speaker
(FR)
Left front
speaker
(FL)
Connecting the surround speakers and the surround back
speakers
1
Twist and remove the insulation at the end of each
speaker cord.
1
Twist and remove the insulation at the end of each
speaker cord.
2
Turn the knob counterclockwise.
3
Insert the speaker cord.
•For each speaker, connect the (+) and (–) terminals on the
rear panel to the (+) and (–) terminals marked on the
speakers.
4
Turn the knob clockwise.
8
2
Open the terminal (1), then insert the speaker cord
(2).
•For each speaker, connect the (+) and (–) terminals on the
rear panel to the (+) and (–) terminals marked on the
speakers.
3
Close the terminal.
*When using a single speaker for the surround back speaker
You can enjoy the surround sound by one surround back
speaker. When using one surround back speaker,
– set “S BACK OUT” to “SB OUT <1SPK>” (see page 23) and
– connect the surround back speaker to the left surround back
speaker terminal. (No sound comes from the speaker if
you connect it to the right surround back speaker
terminal.)
Connecting the powered subwoofer
By connecting a subwoofer, you can enhance the bass or
reproduce the original LFE signals recorded in digital software.
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cord
with RCA pin plugs (not supplied).
• Refer also to the manual supplied with your subwoofer.
After connecting all the speakers and/or a subwoofer, set the
speaker setting information properly to obtain the best possible
surround effect. For details, see pages 20 to 24.
NOTE
You can place a subwoofer wherever you like since bass sound is
non-directional. Normally place it in front of you.
VCR(DBS) IN
DVR/DVD IN MONITOR OUT
HDMI
Connecting video components
Do not connect the AC power plug to the wall outlet until all connections are completed.
HDMI connection
IMPORTANT:
The HDMI video signals from the HDMI terminal are transmitted only through the HDMI MONITOR OUT terminal.
Therefore, if the TV is connected to the receiver through the VIDEO jack (MONITOR OUT), S-VIDEO jack (MONITOR OUT), or
COMPONENT VIDEO jacks (MONITOR OUT) and a playing video component is connected to the receiver through the HDMI terminal
(VCR (DBS) IN or DVR/DVD IN), you cannot view the playback picture on the TV.
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
HDMI cable
(not supplied)
DVD recorder or
DVD player
TV
VCR (or DBS)
Converting video signals into HDMI signals
This receiver can convert composite video, S-video, and component video signals into HDMI signals. To use this function, you need
to make the following procedure beforehand:
1 Connect your TV and this receiver with the HDMI cable.
2 Set the “VIDEO OUTPUT” (see page 26) setting to “VIDEO <HDMI>.”
3 Set the “VIDEO INPUT” (see page 17) setting according to the connection method for each video component.
NOTES
• When playing back audio and video with the HDMI connection, the HDMI lamp on the front panel lights up.
• Set the “AUDIO INPUT” setting to “HDMI” when you enjoy sound with the HDMI connection. See “Selecting the audio input setting” on
pages 16 and 17.
• With input video signals converted into HDMI signals, the playback picture may be distorted when you change the playback mode
(fast-forward, rewind, or pause, for example).
• When connecting a VCR or DBS to HDMI VCR (DBS) IN terminal, select “HDMI SELECT” (see page 26) correctly according to the
component you connect. If you do not, you cannot view the playback picture on the TV.
• By using a HDMI-DVI conversion cable, you can connect the source components or the TV with DVI output. When connecting those
components or TV, change the “AUDIO INPUT” setting to other than “HDMI.” (See pages 16 and 17.)
• This receiver is compatible with standard video formats. If non-standard video formats are coming in, the picture may not appear
properly on TV.
• The picture on the TV may not be the same aspect ratio as the ratio set on the source components.
• With the “AUDIO INPUT” set to “HDMI” (see pages 16 and 17), the sound may be transmitted to the speakers of the TV as well. To use
the speakers connected to the receiver only, set the TV volume to “0.”
• When enjoying multi channel PCM sound with the “AUDIO INPUT” set to “HDMI” (see pages 16 and 17), some functions are not
available. See page 11 for details.
• When you enjoy HDCP contents, sound and picture may not be transmitted to the speakers and TV for a few seconds in the beginning
for confirmation.
9
ı
ΉÏÌ
Ç
Å
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
Y
P
B
P
R
COMPONENT VIDEO
MONITOR
OUT
DVR/DVD
IN
VCR(DBS)
IN
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
FRONT
Audio/video connection
In addition to the HDMI terminal, this receiver is equipped with three
video terminals—composite video, S-video, and component video
terminals, and two audio jacks—analog discrete 5.1 channel audio input
jacks (DVD MULTI IN), and stereo audio jacks.
• If your video components have S-video (Y/C-separation) and/or
component video (Y, P
B, PR) jacks, connect them using an S-
video cable (not supplied) or component video cable (not
supplied). By using these terminals, you can get a better picture
quality in the order:
Component > S-video > Composite
IMPORTANT:
The video signals from one type of these input jacks are
transmitted only through the video output jacks of the same
type. Therefore, if a recording video component and a playing
video component are connected to the receiver through the video
terminals of different type, you cannot record the picture. In
addition, if the TV and a playing video component are connected
to the receiver through the video terminals of different type, you
cannot view the playback picture on the TV.
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a DVD recorder or DVD player with its stereo output jacks:
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
DO NOT use a TV through a VCR or a TV with a built-in
VCR; otherwise, the picture may be distorted.
CAUTION:
If you connect a sound-enhancing device such as a graphic
equalizer between the source components and this receiver, the
sound output through this receiver may be distorted.
If your video components have AV COMPU LINK terminal
See also page 38 for detailed information about the connection
and the AV COMPU LINK remote control system.
: signal current
Green
Component video cable (not supplied)
Blue
Red
DVD recorder or
DVD player
White
Red
Red
White
Stereo audio cable
(not supplied)
Composite video cable
(not supplied)
S-video cable (not supplied)
Composite video cable (not supplied)
NOTES
• Select the audio and video input setting according to the connection method.
See pages 16 and 17 for details.
• You can enjoy digital sound if using a digital coaxial or optical cable. When
shipped from the factory, the digital coaxial terminal (DIGITAL IN 1 (DVR/
DVD)) on the rear of the receiver is set for a DVD recorder and DVD player.
For details of digital audio connection, see page 14.
10
Å To component video output
• Connect Y, P
B, and PR correctly.
ı To left/right audio channel output
Ç Only for DVD recorder: To left/right audio
channel input
Î To composite video output
‰ To S-video output
Ï Only for DVD recorder: To S-video input
Ì Only for DVD recorder: To composite
video input
Å
Ï
Ó
ı
Ç
Î
‰
Ì
Ô
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
FRONT
COMPONENT VIDEO
MONITOR
OUT
DVR/DVD
IN
VCR(DBS)
IN
DVD
MULTI IN
CENTER
SUBWOOFER
SURR-L
SURR-R
È
Y
P
B
P
R
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a DVD recorder or DVD player with its analog discrete output jacks (DVD MULTI IN):
If your DVD recorder or DVD player has analog 5.1 channel output jacks, use the connection below. When a DVD Audio disc is played
back, the original high-quality sounds can be reproduced by using this connection.
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
: signal current
Green
Component video cable (not supplied)
Blue
Red
S-video cable (not supplied)
Composite video cable (not supplied)
Monaural audio cable
(not supplied)
Monaural audio cable
(not supplied)
White
Red
Red
White
Stereo audio cable
(not supplied)
Stereo audio cable
(not supplied)
Composite video cable
(not supplied)
DVD recorder or
DVD player
Å To left/right surround channel audio output
ı To center channel audio output
Ç To component video output
• Connect Y, P
B, and PR correctly.
Î To subwoofer output
‰ To left/right front channel audio output
When you enjoy sound recorded in DVD-Audio...
You can enjoy sound recorded in DVD-Audio both with analog
or digital methods.
– With analog method:
• connect your DVD recorder or DVD player to this receiver
according to the diagram above.
• select “A MULTI” setting for “AUDIO INPUT.” (See pages 16
and 17.)
– With digital method:
• connect your DVD recorder or DVD player and TV to this
receiver with the HDMI cables. (See page 9.)
• select “HDMI” setting for “AUDIO INPUT.” (See pages 16
and 17.)
Ï Only for DVD recorder: To left/right front channel
audio input
Ì To composite video output
Ó To S-video output
È Only for DVD recorder: To S-video input
Ô Only for DVD recorder: To composite video input
NOTES
• When using the headphones, you can listen to the front
channel sounds (left and right) only. 3D HEADPHONE mode
(see page 35) is not available.
• When selecting “A MULTI” setting for “AUDIO INPUT” or when
multi channel PCM signals (see page 34) are coming in with
selecting “HDMI” setting for “AUDIO INPUT,” the following items
are not available:
– DECODE MODE (see page 18)
– EX/ES/PLllx (see page 24)
– DUAL MONO (see page 24)
– SUBWOOFER OUT (see page 24)
– CROSSOVER (see page 25)
– LFE ATT (see page 25)
– Midnight Mode (see page 25)
– AUDIO DELAY (see page 26)
– DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz (see page 28)
– BASS BOOST (see page 29)
– INPUT ATT (see page 29)
– Sound parameters for Surround/DSP modes (see pages 29
and 30)
– Surround/DSP modes (see pages 33 to 37)
• When you enjoy sound recorded in DVD-Audio through the
HDMI connection, use a DVD recorder or DVD player
compatible with HDMI version 1.1.
11
VCR
OUT(REC) IN(PLAY)
AUDIO
OUT(REC) IN(PLAY)
VCR
Å
ı
ΉÏÌÇ
Y
P
B
P
R
COMPONENT VIDEO
MONITOR
OUT
DVR/DVD
IN
VCR(DBS)
IN
Å
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a VCR
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
Green
Blue
Red
White
Red
: signal current
Component video cable (not supplied)
VCR
White
S-video cable (not supplied)
Composite video cable (not supplied)
NOTES
• Select the audio and video input setting according to the
connection method. See pages 16 and 17 for details.
• When connecting a VCR to the component video input jacks,
select “CMPNT SELECT” (see page 26) to “VCR.” If you do not,
you cannot view the playback picture on the TV or the AV
COMPU LINK remote control system (see page 38) cannot
operate properly.
• You can enjoy digital sound if using a digital coaxial or optical
cable. When shipped from the factory, the digital optical terminal
(DIGITAL IN 3 (VCR)) on the rear of the receiver is set for a
VCR. For details of digital audio connection, see page 14.
Red
(not supplied)
Composite video
cable (not supplied)
Å To component video output
Stereo audio cable
• Connect Y, P
B, and PR correctly.
ı To left/right audio channel output
Ç To left/right audio channel input
Î To composite video output
‰ To S-video output
Ï To S-video input
Ì To composite video input
12
Å
ı
Î
Ç
Y
P
B
P
R
COMPONENT VIDEO
MONITOR
OUT
DVR/DVD
IN
VCR(DBS)
IN
B
N
/
COMPONENT VIDEO
MONITOR
OUT
DVR/DVD
IN
VCR(DBS)
IN
Y
P
B
P
R
U
Å
ı
ÎÇ
Do not connect the AC power plug to the wall outlet until all connections are completed.
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
7 Connecting a DBS tuner
: signal current
Green
Blue
Red
DBS
IN O
Component video cable (not supplied)
White
Stereo audio cable (not supplied)
Red
DBS tuner
VIDEO
VIDEO
S-VIDEO
VC
DBS
OUT(REC)
IN
NOTES
• Select the audio and video input setting according to the connection method. See pages 16
and 17 for details.
• When connecting a DBS tuner to the component video input jacks, select “CMPNT SELECT”
(see page 26) to “DBS.” If you do not, you cannot view the playback picture on the TV.
• You can enjoy digital sound if using a digital coaxial or optical cable. When shipped from the
factory, the digital optical terminal (DIGITAL IN 2 (DBS)) on the rear of the receiver is set for a
DBS tuner. For details of digital audio connection, see page 14.
Composite video cable
(not supplied)
S-video cable (not supplied)
Å To left/right audio channel
output
ı To component video output
• Connect Y, P
B, and PR
correctly.
Ç To composite video output
Î To S-video output
7 Connecting a TV
Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video components.
Green
Blue
Component video cable (not supplied)
: signal current
Red
TVIND
I
L
White
Red
MONITOR
DVD
OUT
LAY)
R
S-video cable (not supplied)
Composite video cable (not supplied)
NOTES
• Select the audio input setting according to the connection method. See pages
16 and 17 for details.
•You can enjoy digital sound if using a digital coaxial or optical cable. For details
of digital audio connection, see page 14.
• Set the “VIDEO OUTPUT” setting to “OTHER.” See page 26 for details.
Stereo audio cable
(not supplied)
TV
Å To component video input
• Connect Y, P
ı To left/right audio channel output
Ç To S-video input
Î To composite video input
B, and PR correctly.
13
DIGITAL OUT
PCM/STREAM
DIGITAL IN
2(DBS)
1(DVR/DVD)
3(VCR)
Digital audio connection
This receiver is equipped with three DIGITAL IN terminals—one
digital coaxial terminal and two digital optical terminals—and one
DIGITAL OUT terminal.
To reproduce the digital sound, use the digital audio connection in
addition to the analog audio connection methods described on
pages 10 to 13.
Digital coaxial cable (not supplied)
Digital optical cable (not supplied)
Turn off all components before making connections.
• When you connect other components, refer also to their
manuals.
7 Digital input terminals
When the component has a digital coaxial output
terminal, connect it to the 1(DVR/DVD) terminal,
using a digital coaxial cable (not supplied).
7 Digital output terminal
You can connect any digital components which have an optical
digital input terminal.
Connecting digital recording equipment to the
DIGITAL OUT terminal enables you to perform
digital-to-digital recording.
NOTES
• The digital signal format transmitted through the DIGITAL OUT
terminal is the same as that of the input signal. For example,
when the DTS signals are input, the DTS signals are
transmitted.
• The digital signal coming through the USB terminal, and HDMI
input terminal cannot be output from the DIGITAL OUT terminal.
When the component has a digital optical output
terminal, connect it to the 2(DBS) or 3(VCR)
terminal, using a digital optical cable (not supplied).
Before connecting a digital
optical cable, unplug the
protective plug.
NOTES
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components:
– 1(DVR/DVD): For DVD recorder or DVD player
– 2(DBS): For DBS tuner
– 3(VCR): For VCR
If you connect other components, change the digital input
(DIGITAL IN) terminal setting correctly. See “Setting the digital
input (DIGITAL IN) terminals—DIGITAL IN 1/2/3” on page 25.
• Select the correct digital input mode. See “Selecting the audio
input setting” on pages 16 and 17.
Connecting the power cord
When all the audio/video connections have been made, connect
the AC power plug to the wall outlet. Make sure that the plugs are
inserted firmly. The standby lamp lights in red.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
NOTES
•Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen
interference.
• The preset settings such as preset channels and sound
adjustment may be erased in a few days in the following cases:
– When you unplug the power cord.
– When a power failure occurs.
• When you unplug the power cord with the receiver on and
connect the power cord again, the receiver enters standby
mode.
14
Loading...