JVC WB-S622U, WB-S621U, WB-S623U User Manual

About Fall prevention

©

Connect the reinforcement material or reinforcement angle to this
camera to prevent it from falling.
For the used safety cable, pay particular caution to the length,
strength, pull, material.

When the camera mounting plate is
removed.

(Safety cable not included.)

Safety cable

Installing the Camera

Attach the camera to the camera mounting plate.
Ensure that the Front mark on the camera mounting plate aligns
with the Front mark on the camera.
For TK-C625U/E, VN-C625U, TK-C215V4U/E, TK-C215V12U/E
and TK-C210FWE, attach the ceiling panel assembly to the camera
mounting plate before installing the camera.
Mounting Hole A : For TK-C655E, TK-C676E, VN-C655U,

Mounting Hole B : For TK-C625U/E, VN-C625U, TK-C215V4U/E,

Mounting
Hole A

Ceiling Panel
Assembly
Positioning Hole

TK-C205(A)U/E and TK-C205VP(A)U/E

TK-C215V12U/E and TK-C210FWE

Mounting
Hole B

Specifications

Operating temperature :

–10 ˚C to 50 ˚C(14 ˚F to 122 ˚F)

Mass : Body :

 Accessories

(Same for WB-S621U, WB-S622U and WB-S623U)

• Instructions .............................. 1

• Screw (For mounting camera)

• Ceiling Panel Assy................... 1

WB-S621U; 2.0 k˝,
WB-S622U; 1.8 k˝
WB-S623U; 1.0 k˝

Ceiling Panel Assy :

(Same for WB-S621U, WB­S622U and WB-S623U)

M4 x 20 mm

....4,M4 x 10 mm

 External dimensions [Unit:mm(inches)] *Design and specifications are subject to change without notice.

 WB-S621U

)
3/8

85(3

85(3

3/8

)

4-q6,5(4-q1/4
(Ceiling Mount Hole)

q

140(5

1/2

)

)

1/4

6.7(

q

160(6

1/4

)

2006 Victor Company of Japan, Limited

 Ta bulation of mass (combined mount and Camera)

WB-S621U
Applicable

TK-C625U

TK-C205U

0.57 k˝

TK-C205U

0.57 k˝

TK-C205U

0.57 k˝

q160(6

1/4

TK-C205VPU

TK-C205VPU

TK-C205VPU

332(13

)

)

)
1/4
6(

42

37.4 ˝

....

)
5/8
(1

Camera
Total mass

WB-S622U
Applicable

Camera
Total mass

WB-S623U
Applicable

Camera

4

Total mass

1.3 k˝

3.3 k˝ 2.57 k˝ 3.3 k˝ 3.2 k˝ 4.2 k˝

TK-C625U

1.3 k˝

3.1 k˝ 2.37 k˝ 3.1 k˝ 3.0 k˝ 4.0 k˝

TK-C625U

1.3 k˝

2.3 k˝ 1.57 k˝ 2.3 k˝ 2.2 k˝ 3.2 k˝

 WB-S622U

)

3/4

120(4

)

1/4

6.7

(

 WB-S623U

560(22)

)
3/4

95(3

)
1/4

6.7(

q16

0(6

1/4

)

2.0 k˝

1.3 k˝

1.8 k˝

1.3 k˝

1.0 k˝

1.3 k˝

1/8

)

VN-C625U

1.2 k˝

VN-C625U

1.2 k˝

VN-C625U

1.2 k˝

)
3/4

95(

83,5(3

VN-C655U

2.2 k˝

VN-C655U

2.2 k˝

VN-C655U

2.2 k˝

)

1/4

185(7

1/4

)

Camera Mounting
plate

Mounting
Hole A

Mounting
Hole B

Front Mark

TK-C215V4U

TK-C215V12U

0.47 k˝

0.53 k˝

2.47 k˝ 2.53 k˝

TK-C215V4U

TK-C215V12U

0.47 k˝

0.53 k˝

2.27 k˝ 2.33 k˝

TK-C215V4U

TK-C215V12U

0.47 k˝

0.53 k˝

1.47 k˝ 1.53 k˝

80(3

1/8

)

2- R3
(2- R

60(2

3/8

)

)

1/2

115(4

2-q6(2-

q

1/4

)

(Wall Mounting Hole)

4-q4,5(4-q

1/8

)

(Ceiling Mount Hole)

)
3/4

1

46

(

LWT0267-001D

WB-S621U Pendant Mount
WB-S622U Wall Mount
WB-S623U Ceiling Bracket

Thank you for purchasing this product.

To obtain the best results from your bracket, read these instructions carefully before use; retain the manual for future reference.
This instruction manual is made from recycled paper.
The "INSTRUCTIONS" section below is applicable to WB-S621U/WB-S622U/WB-S623U. Please refer to the installation procedures for the purchased
product during installation.

For Customer Use:

Enter below the Serial No. which is located on the body.
Retain this information for future reference.

Model No.

Serial No.

These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances.

INSTRUCTIONS

(

A

)

IMPORTANT SAFEGUARDS

1. Read all of these instructions.

2. Save these instructions for later use.

3. All warnings on the product and in the operating instructions should be adhered to.

4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.

6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool,
etc.

7. Do not place this appliance on an unstable cart, stand, or table. The appliance may fall, causing serious injury to a child or adult, and
serious damage to the appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance.
Use only with a cart or stand recommended by the manufacturer, or sold with the appliance. Wall or shelf mounting should followthe
manufacturer’s instructions, and should use a mounting kit approved by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.

8. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the
appliance and to protect it from overheating, these openings must not be blocked or covered. The openings should never be
blocked by placing the appliance on a bed, sofa, rug, or other similar surface. This appliance should never be placed near or
over a radiator or heat register. This appliance should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

9. This appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company. For appliance designed to operate from battery power, refer to the operating instructions.

10. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

11. Do not allow anything to rest on the power cord. Do not locate this appliance where the cord will be abused by persons walking on it.

12. Follow all warnings and instructions marked on the appliance.

13. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

14. Never push objects of any kind into his appliance through cabinet slots as they mat touch dangerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on the appliance.

15. Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.

16. Unplug his appliance from the wall outlet and refer servicing to qualified service personnel under following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.

1/8

)

)

3/8

136(5

c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating

instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualifiedtechnician to restore the

appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been damaged.
f. When the appliance exhibits a distinct change in performance - this indicates a need for service.

17. When replacement parts are required, be sure the service technician has used replacement par ts specified by the manufacturer that have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

18. Upon completion of any service or repairs to this appliance, ask the service technician to perform routine safety checks to determine that the appliance
is in safe operating condition.

For USA and CANADA

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, with
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instruc­tions in the literature accompanying the appliance.

in an equi-lateral triangle, is

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.

PORTABLE CART WARNING
(symbol provided by RETAC)

S3125A

Precaution

 This equipment is intended for indoor use only. Do not use it

outdoors or at places that are exposed to rain or moisture.

 Do not attach devices other than TK-C625U/E, TK-C655E, TK-

C676E, TK-C205(A)U/E, TK-C205VP(A)U/E, VN-C625U, VN­C655U, TK-C210FWE, TK-C215V4U/E and TK-C215V12U/E to
this mount/bracket.
The suffix E of model No. specifies the exclusive variant for
European market.

 Install this mount/bracket horizontally. Do not tilt it during use.
 Do not install or use the unit in the following places.

• In a place exposed to rain or moisture.

• In a temperature outsside the operating temperature range
(–10˚C to 50˚C (14˚F to 122˚F)).

• In a place where corrosive gasses are generated.

• In a place subject to vibration.

 When attaching VN-C625U, VN-C655U to this mount/bracket,

please refer to the "INSTRUCTIONS" section of VN-C625U, VN­C655U for procedures to install the converter unit.

 Please refer to the "INSTRUCTIONS" section of the camera in

use for procedures to attach the camera.

Installation Procedures

 These installation should be made by a qualified service person and should conform to all local codes.
 These installation should be in accordance with the National Electrical Code ANSI/NFPA 70.
 Use the appropriate mounting hardware for the surface selected.

Installing the Converter Unit

When using VN-C625U or VN-C655U, attach using the clamping bracket
inside the top cover of the converter unit (supplied with the camera).

Converter Unit

WB-S621U Pendant Mount

1.

When a hole is not
made in the ceiling

Groove

Cable

4. Fall prevention

Safety cable Mount
Hole ( 4.5 mm)

Bolt (M4)

Front Mark

Camera
Mounting Plate

Ceiling Panel Assy

Nut (M4)

Reinforcement Angle

2.

Safety cable

Protruding Part

1.

FRONT Mark

5.

Cables

3.

Ceiling Panel
Assembly
Positioning
Hole

Top cover

Screws
(3 locations)

Make a hole in the ceiling.

To route cables through the ceiling, make a hole of  30 mm ( 1 1/4)
in the ceiling.

2.

Route the safety cable and other cables

Route the safety cable and cables that is attached to the reinforce­ment angle through the pendant mount.
When a hole is not made in the ceiling, route the cables through the
groove of the pendant Mount.

3.

Mount the Pendant Mount to the Ceiling.

Attach the pendant mount to the ceiling.

CAUTION

The camera may drop or images on the screen may appear shaky
if the ceiling material is not strong enough. In this case, reinforce
using a reinforcement materials.

4.

Connect the safety cable.

Upon removing the camera mounting plate, attach the safety cable
(not supplied) to the safety cable mount hole ( 4.5 mm ( 1/8")) at
the interior of the top cover using the M4 Bolt (not supplied) and M4
Nut (not supplied).
When attaching the camera mounting plate, ensure that the Front
mark on the camera mounting plate is facing a direction to the Front
mark on the top cover.

CAUTION

Pay particular caution to the length, strength, pull and material of
the safety cable in use to prevent the plate from falling.

5.

For attaching TK-C625U/E, VN-C625U, TK-C210FWE, TK-C215V4U/E and TK-C215V12U/E
Install the ceiling panel assembly

To install, align the protruding par t of the ceiling panel assembly
with the ceiling panel assembly positioning hole near the Front mark
of the camera mounting plate. Ensure to tighten the screws (3
locations) assembled to the ceiling panel assembly.

NOTE

The screws are assembled to the ceiling panel assembly in such
a way that they will not come off.

6.

Connect the Cables.

Connect cables to the camera.
For details, please refer to "INSTRUCTIONS" section of the camera
in use.

7.

Attach the camera's ceiling mount (outer case). (Not
applicable to TK-C205(A)U/E and TK-C205VP(A)U/E)

Attach the camera's ceiling mount (outer case) to the camera mount­ing plate using the 4 screws (M4 x 10 mm) for TK-C210FWE, TK­C215V4U/E and TK-C215V12U/E, and the other 4 screws (M4 x 20
mm) for the other cameras supplied with the pendant mount. Ensure
that the FRONT mark on the camera mounting plate aligns with the
Front mark on the ceiling mount.

NOTE

It is not necessary to use the adapter ring supplied with TK-C215.

Top cover

Clamping Bracket

WB-S622U Wall Mount

1.

Make a hole

When a hole is not
made in the wall

Groove

1.

Safety
cable

Cables

Cover

Cover Mounting
Screw

Front Mark

Top cover

Front Mark

2.

Camera Mounting

3.

Plate

Ceiling Panel Assy

6.

Connect the cables.

Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use.

7.

Attach the camera's ceiling mount (outer case). (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E)

Attach the camera's ceiling mount (outer case) to the camera mounting plate using the 4 screws (M4 x 10 mm) for TK-C210FWE, TK-C215V4U/
E and TK-C215V12U/E, and the other 4 screws (M4 x 20 mm) for the other cameras supplied with the wall mount. Ensure that the Front mark
on the camera mounting plate aligns with the Front mark on the ceiling mount.

NOTE

It is not necessary to use the adapter ring supplied with TK-C215.

5.

Screws
(3 locations)

Protruding
Part

Ceiling Panel
Assembly
Positioning Hole

To route cables through the wall, make a hole of 30 mm (  1 1/8") in the wall.

2.

Route the safety cable and other cables

Open the cover and route the safety cable and other cables through this wall mount.
Please refer to "About Fall Prevention" for procedures to install the safety cable.
When a hole is not made in the wall, route the cables pulled to the wall stand
through the groove of the Wall Mount.

CAUTION

The camera may drop or images on the screen may appear shaky if the ceiling
material is not strong enough. In this case, reinforce using a reinforcement materials.

3.

Attach the wall mount to the wall

Attach the wall mount to the wall.

4.

Connect the safety cable.

Upon removing the camera mounting plate, attach the safety cable (not
supplied) to the interior of the top cover using the M3 screw. (Refer to "About
Fall Prevention".)
When attaching the camera mounting plate, ensure that the Front mark on the camera
mounting plate is facing a direction to the

5.

For attaching TK-C625U/E, VN-C625U, TK-C210FWE, TK-C215V4U/E and TK-C215V12U/E
Install the ceiling panel assembly

To install, align the protruding part of the ceiling panel assembly with the ceiling panel
assembly positioning hole near the Front mark of the camera mounting plate.
Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly.

NOTE

The screws are assembled to the ceiling panel assembly in such a way that
they will not come off.

Front

mark on the top cover.

WB-S623U Ceiling Bracket

1.

Reinforcement
Angle

Front Mark

Top cover

Camera
Mounting
Plate

Ceiling Panel Assy

6.

Connect the cables.

Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use.

7.

Attach the camera's ceiling mount (outer case). (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E)

Attach the camera's ceiling mount (outer case) to the camera mounting plate using the 4 screws (M4 x 10 mm) for TK-C210FWE, TK­C215V4U/E and TK-C215V12U/E, and the other 4 screws (M4 x 20 mm) for the other cameras supplied with the ceiling bracket. Ensure that
the Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount.

NOTE

It is not necessary to use the adapter ring supplied with TK-C215.

2.

Protruding
Part

Safety cable

Cables

1.

3.

Screws
(3 locations)

When a hole is not
made in the ceiling

Front Mark

Ceiling Panel
Assembly

5.

Positioning Hole

Cap

Make a hole in the ceiling.

To route cables through the ceiling, make a hole of 30 mm ( 1 1/8") in the ceiling.

2.

Route the safety cable and other cables

Route the safety cable and other cables through the ceiling bracket. Please
refer to "About Fall Prevention" for procedures to install the safety cable.
When a hole is not made in the ceiling, route the cables through the hole at
one side of the Ceiling Bracket. Remove the cap covering the hole before
routing the cables through.

CAUTION

The camera may drop or images on the screen may appear shaky if the ceiling
material is not strong enough. In this case, reinforce using a reinforcement materials.

3.

Mount the ceiling bracket to the ceiling.

Mount the ceiling bracket to the ceiling.

4.

Connect the safety cable.

Upon removing the camera mounting plate, attach the safety cable (not supplied)
to the interior of the top cover using the M3 screw. (Refer to "About Fall Prevention".)
When attaching the camera mounting plate, ensure that the Front mark on the camera
mounting plate is facing a direction to the

5.

For attaching TK-C625U/E, VN-C625U, TK-C210FWE, TK-C215V4U/E
Install the ceiling panel assembly

To install, align the protruding part of the ceiling panel assembly with the ceiling panel
assembly positioning hole near the Front mark of the camera mounting plate.
Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly.

NOTE

The screws are assembled to the ceiling panel assembly in such a way that
they will not come off.

Front

mark on the top cover.

and

TK-C215V12U/E