JVC VN-C10 User Manual
V.NETWORKS
VN-C10
READ ME FIRST
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. VN-C10
Serial No.
This READ ME FIRST is made from 100 % recycled paper.
LWT0083-001C
IMPORTANT SAFEGUARDS
1. Read all of these instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions should be adhered to.
4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.
6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool, etc.
7. Do not place this appliance on an unstable cart, stand, or table. The appliance may
fall, causing serious injury to a child or adult, and serious damage to the appliance.
Use only with a cart or stand recommended by the manufacturer, or sold with the
appliance. Wall or shelf mounting should follow the manufacturer’s instructions, and
should use a mounting kit approved by the manufacturer. An appliance and cart
combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the appliance and
cart combination to overturn.
8. Slots and openings in the cabinet and the back or bottom are pro-vided for ventilation, and to insure reliable operation of the appliance and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing
the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or heat register. This appliance should not be
placed in a built-in installation such as a bookcase unless proper ventilation is provided.
9. This appliance should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your dealer or local power company. For
appliance designed to operate from battery power, refer to the operating instructions.
10. This appliance system is equipped with a 3-wire grounding type plug (a plug having a third (grounding) pin).
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding plug.
11. For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it form the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
12. Do not allow anything to rest on the power cord. Do not locate this appliance where the cord will be abused by
persons walking on it.
13. Follow all warnings and instructions marked on the appliance.
14. Do not overload wall outlets and extension cords as this can result in fire or electric shock.
15. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
appliance.
16. Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
17. Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the operating instructions. Adjust only those con-
trols that are covered by the operating instructions as improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the appliance to normal
operation.
e. If the appliance has been dropped or the cabinet has been damaged.
f. When the appliance exhibits a distinct change in performance - this indicates a need for service.
18. When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
19. Upon completion of any service or repairs to this appliance, ask the service technician to perform routine
safety checks to determine that the appliance is in safe operating condition.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3125A
2
Safety Precautions
FOR USA AND CANADA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK. DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE.REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash wish arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Information for USA
This device complies with part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
Due to design modifications, data given in this
instruction book are subject to possible change
without prior notice.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
AVERTISSEMENT:
POUR EVITER LES RISQUES
D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA
PLUIE.
INFORMATION (FOR CANADA)
RENSEIGNEMENT
This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Class A est
conforme á la norme NMB-003 du Canada.
(POUR CANADA)
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Information for Europe
Warning:
This is a class A product. In a domestic environment
this product may cause radio interference in which
case the user may be required to take adequate
measures.
3
Thank you for purchasing this product.
(These instructions are for VN-C10U.)
Before beginning to operate this unit, please read the instruction manual carefully in
order to make sure that the best possible performance is obtained.
Contents
Introduction
Preparations
Contents ................................................................................................. 4
Features .................................................................................................5
Items Included ........................................................................................ 5
Required Operating Environment........................................................... 6
Upgrading the Application ......................................................................6
Operating Precautions ........................................................................... 7
Controls, Connectors and Indicators ...................................................... 8
Connection Examples .......................................................................... 10
Preparation Procedure .........................................................................11
Step 1 Connection and Installation
Attaching a Lens ................................................................................12
Connecting the Power Cord............................................................... 13
Connecting a LAN Cable ................................................................... 14
Installing the Camera ......................................................................... 15
Step 2 Setting the Network
Installing the Software ....................................................................... 16
Setting the PC’s IP Address for Windows XP .................................... 17
Setting the PC’s IP Address for Windows 2000 .................................19
Setting the IP Address for VN-C10 with V.Networks Setup Tool ........ 21
Registering the Connected Camera with V.Networks Controller ...................
Step 3 Adjusting the Camera
Back-focus Adjustment ......................................................................24
23
Operations
Others
4
Step 4 Setting with V.Networks Controller
Starting Up V.Networks Controller ..................................................... 25
Function Settings with V.Networks Controller .................................... 26
Step 5 Operations with V.Networks Controller
Operations with V.Networks Controller .............................................. 27
Step 6 Operations with a Web Browser
Required Operating Environment ...................................................... 28
Access Authorization ......................................................................... 29
Starting Up the Web Browser ............................................................ 30
Specifications ..................................................................................... 31
External Dimensions .........................................................................31
Introduction
Features
• VN-C10 uses a 1/3-inch CCD with 380,000 pixels, enabling monitoring of high quality images.
•For the compression method, in addition to the standard JPEG, VN-C10 supports MPEG4 for a
wide range of bit rates. (With MPEG4, up to 4 clients can be connected at one time.)
• Equipped with an image recording function by motion detection and alarm input.
• VN-C10 has a design similar to other CCTV monitoring cameras, allowing peripheral equipment
for such cameras to be also used for VN-C10.
• With a built-in Web server, VN-C10 supports Internet Explorer and Netscape.
• Multicast function. (Only for JPEG)
Items Included
CD-ROM
(The PDF instruction manual inside) Read Me First
Warranty Card Service Information Card
How to Use This Manual
Characters and Symbols used in this Manual
Caution
Note
Operational points special attention should be paid to, because of, for example,
danger involved.
Functional or operational tips.
☞ Pages or items to refer to.
❈ In no case, shall JVC be held liable for any loss or damage to the customer or for any claim
from any third party arising from using this software.
For the purpose of improving the product, the software specifications are subject to change
without prior notice.
The product names that appear in this document are brand names or registered trademarks
of each relevant company. Marks and symbols such as ™, ® and © do not appear in this
document.
To see the content of the PDF instruction manual inside the supplied CD-ROM,
it is required that the Adobe Acrobat Reader is installed in the PC.
5
Introduction
Required Operating Environment
PC Specifications
OS : Windows 2000 (Service Pack 1 or higher)
CPU : Pentium
Memory Capacity : 128 MB or more
Hard Disk Space : 20 MB or more
Display/Video Card : 1024 X 768 pixels or more, True Color (24 bits or 32 bits)
Windows XP Home Edition
Windows XP Professional
III 500 MHz or higher (1 GHz or higher recommended)
LAN Specifications
• 10 BASE-T/100 BASE-TX network connected with IEEE802.3 hubs.
Note
The PC specifications above are only for a reference purpose. They are not meant to guarantee a smooth operation of the application software. Depending on the usage of the PC, there
may be cases where problems occur even if the PC satisfies the technical requirements.
Caution
If the OS specifications of the PC to be used are higher, they precede those described above.
Upgrading the Application
For information on upgrading the application, visit the following website.
http://www.jvc-victor.co.jp/english/pro/vnetworks/index-e.html
6
Operating Precautions
● VN-C10 is designed for indoor use. For outdoor use, prepare a proper housing to cover and
protect the camera.
● The product should not be installed or used in the following locations.
• Locations subject to rain or water.
• Locations with hot air or oil vapors such as in kitchens, etc.
• Locations where the allowed ambient temperature (0 °C to 40 °C) is exceeded.
• Locations exposed to X-ray radiation or where strong electrical or magnetic waves are gener-
ated.
• Locations where corrosive gas is generated.
• Locations with vibrations.
• Locations with excessive dust.
● If VN-C10 and the cables connected to VN-C10 are installed at a location where strong electrical
or magnetic waves are generated, near a radio, TV set, transformer, motor etc., the quality of
image and color may be affected.
● If a high-intensity object (such as a lamp) is shot, the image on the screen may have vertical lines
(smear) or blur (blooming) at its periphery. This is a characteristic of the CCD, and is not a defect.
● Clean the unit with the power turned off. Use a soft cloth like cotton flannel to wipe out dirt. Do not
use paint thinner or benzine as a cleaning agent as this may cause melting or tarnishing of the
unit surface. If dirt is persistent, use a cloth soaked with water-diluted mild detergent and then
wipe it with a dry cloth.
● Because the cable holders of the terminals could come loose, perform cable connection carefully
and securely.
● Insufficient dissipation of heat from the unit may cause damage. Use the unit at a well-ventilated
location. In particular, do not block the unit’s cooling-fan ventilation opening.
● In a narrowband environment, for example, of dial-up connection, smooth running of MPEG4
images cannot be obtained. This is due to the product design, therefore not a defect.
● When this product is installed in an NAT environment, MPEG4 images cannot be viewed. This is
due to the product design, therefore not a defect. (This product uses a network protocol called
RTP for transmitting MPEG4 images. Generally, an NAT router cannot carry out NAT translation
of RTP packets properly.)
● Certain hubs and switches equipped with SNMP functions have a broadcast or multicast control
function. If the function is enabled, multicast images created by this product may not be viewed
properly.
● To save electricity, turn off the power to the system when not in use.
● As local recording images are saved to the volatile memory of the product, the images are
deleted if the power is turned off.
7
Introduction
Controls, Connectors and Indicators
(Front, top and side views)
2
1
3
4
5
8
7
1 Lens mount
The mount for attaching a lens. Either a Cmount or a CS-mount lens can be used.
2 Back-focus adjustment ring
The ring for adjusting back-focus and changing the mount method. For adjusting back-focus or changing the mount method, loosen
the back-focus locking screw (3) by turning it
counterclockwise and, after the operation, fix
it by turning it clockwise. At the factory, VNC10 is optimized for attaching a CS mount
lens.
3 [BF LOCK] locking screw
This serves to fix the back focus-adjustment
ring.
4 Bracket for camera mounting.
At the factory, the bracket is attached on the
bottom of the camera. According to the installation condition, this can be attached at the
top. Use the screws (7 ) for attaching the
bracket to the camera.
6
5 Screw hole (1/4-20UNC)
For attaching the camera to
a fixer or a pan/tilt unit. The
screw length must not exceed 7 mm. If a longer screw
is used, the internal parts of
the camera may be damaged.
6 Fall-preventive holes
For installing the camera securely, use these
holes to prevent it from falling off.
7 Screws for the bracket (x 2: M2.6 X 6 mm)
Screws of the length of 6 mm should be used.
A longer screw may damage the internal parts.
8 [MAC address]
Physical address unique to the unit. Cannot
be changed.
MAX.
7 mm
8
Controls, Connectors and Indicators (continued)
(Side and rear views)
9
0
RESET
9 Ventilation opening
For the internal cooling fan. Install the camera in a way that does not cover the opening.
0 [RESET] button
Press this button to reset VN-C10. If this button is held down for 2 seconds or longer, the
values set with [V.Networks Setup Tool] return to those set at the factory, and VN-C10
restarts.
! [IRIS] terminal
For connecting with a DC IRIS lens.
(A video iris lens cannot be connected.)
@ [POWER] indicator
This indicator starts blinking when the power
is turned on. When the camera is ready for
network connection, this becomes steady on.
If the indicator blinks while the camera is in
use, check the camera and/or the network
equipment.
!
IRIS
@
DC12V
#
AC24V
POWER
$ %
21
G
USA
ONLY
For
For EUROPE
POWER
ONLY
2
INPUT
ISOLATED
CLASS
PUSH
For USA
# [DC 12 V/AC 24 V] Power terminal
For connecting to a DC 12 V or AC 24 V, 50 Hz/
60 Hz, power source. (
$ [ALARM INPUT] terminals
For connecting with an external alarm equipment.
% [ALARM OUTPUT] terminals
For connecting with an external alarm equipment.
^ [10 BASE-T/100 BASE-TX]
For network connection with a LAN cable.
☞ Page 14)
(
OUT COM
1
2
OUTPUT
ALARM
10BASE-T/100BASE-TX
DO NOT CONNECT TO THE
TELEPHONE NETWORK
^
☞ Page 13)
9
Preparations
Connection Examples
LAN Connection
VN-C10
L H
LEVEL
ALC
Av Pk
MAC address
BF LOCK
VN-C10
L H
LEVEL
BF LOCK
ALC
Av Pk
Network Connection
VN-C10
L H
LEVEL
ALC
Av Pk
L H
LEVEL
ALC
Av Pk
MAC address
BF LOCK
VN-C10
MAC address
BF LOCK
FTP Server
LAN
MAC address
PC
LAN INTERNET
PCPC Images are automatically
updated at a regular interval.
Peer-to-Peer Connection
VN-C10
L H
LEVEL
ALC
Av Pk
MAC address
BF LOCK
10
PC
Loading...